Page 1
Marshall Electronics
Model No. V-LCD17HR
Rack Mountable High Definition LCD Monitor
Operating Instructions
Edition 2 Revision 1W
Page 2
2
This page intentionally left blank
Page 3
3
Table of Contents
Installation and Initial Setup ------------------------------------------------------------------------------------------------------4
Top and Front Panel Features ----------------------------------------------------------------------------------------------------5
Rear Panel Features----------------------------------------------------------------------------------------------------------------- 6
Compatible Input Formats--------------------------------------------------------------------------------------------------------- 6
MAIN MENU AND NAVIGATION-------------------------------------------------------------------------------------------------- 7
VIDEO CONFIGURATION SUBMENU ...................................................................................................................................................... 7
MARKER CONFIGURATION SUBMENU ..................................................................................................................................................8
FILTER CONFIGURATION SUBMENU....................................................................................................................................................11
SYSTEM CONFIGURATION SUBMENU .................................................................................................................................................12
FUNCTION PRESETS SUBMENU ........................................................................................................................................................... 12
IMD CONFIGURATION .........................................................................................................................................................................13
SYSTEM INFORMATION SUBMENU ..................................................................................................................................................... 13
Specifications ----------------------------------------------------------------------------------------------------------------------- 15
Dimensions-------------------------------------------------------------------------------------------------------------------------- 15
Maintenance------------------------------------------------------------------------------------------------------------------------ 20
Warranty ---------------------------------------------------------------------------------------------------------------------------- 20
Page 4
4
Installation and Initial Setup
■ Unpacking
Carefully unpack the V-LCD17HR monitor and verify that the following items are included:
• V-LCD17HR Monitor
• V-PS12-5V-1 Power Supply
• Operating Instructions
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at (800) 800-6608.
If you are not located within the continental United States, call +1 (310) 333-0606.
■ Installation
The V-LCD17HR can be mounted in any standard EIA 19” equipment rack. The attached rack ears can be angled to provide the user control over the viewing angle. Adequate
ventilation is required when installed to prevent possible damage to the monitor’s internal components. Please see the Dimensions section for more information.
A VESA standard 75mm hole pattern also allows custom mounting installations. Alternately, the V-LCD17HR can be used in a desktop configuration with optional stand.
Please contact Marshall Electronics for more information.
■ Connections, Power-On and Initial Setup
Plug the power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the Power connector to the back of the monitor. Connect the required cables for video signal
input and output. (Power must be applied to the V-LCD17HR for the active loop-though output to be activated.) The monitor defaults to ‘ON’ when power is supplied. Video
will automatically be detected and displayed on the screen.
Page 5
5
Top and Front Panel Features
Power Button
Use the power button to toggle between ON and STANDBY modes. In both the
STANDBY and the ON state, the LED on the button will illuminate bright green. This
indicates that MAIN power is applied to the unit.
User-Definable Function Buttons
Two user-definable function buttons can be used for direct access to various
settings. Functions are assigned using the on-screen menu.
Menu Navigation Buttons
Use the Menu, ▲, ▼, and Select buttons to display and navigate the on-screen
menu (See Main Menu and Navigation).
Image Adjustment Knobs
Use the image adjustment knobs to adjust color brightness, color-saturation, tint,
and contrast of the image. The status of each image adjustment parameter is shown
on the bottom left of the screen, with values ranging from 0 to 100. Default value is
50.
LED Tally
Three LED tally lights (yellow, red, green) are available above the screen.
Page 6
6
Rear Panel Features
Power Input
Connect 12VDC to the 4-pin XLR power input connector. Power should only be
supplied from the included power supply.
IMPORTANT: If using a power source other than the included power supply, damage
may result. Please use the pin out diagram in the Specifications section.
Tally Input Connector
The LED tally can be activated via the HD-15 connector by connecting the
corresponding pin to ground. A variety of external devices can be used to perform
the contact closure. No additional power should be supplied to the HD-15 port.
Desktop Mounting Holes
These holes are used when attaching the monitor to the optional desktop
stand.
VESA 75mm Hole Pattern
VESA-standard 75 mm hole-patterns is provided to accommodate a variety of
custom mounting options. See Dimensions for further details.
Input Connection
The V-MD monitor comes preconfigured with 3G-SDI and a Loop Out or 2xHDSDI
inputs. See the Compatible Input Formats list for compatible formats.
PROG Port
The PROG port is a Service / Upgrade port only. Please contact Marshall Electronics
for more information.
Compatible Input Formats
MD-3GSDI and MD-TC – 3G/HD/SDI Input Module with Loop-Through
525i, 625i/50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29, 30
1080i/50, 59.94, 60
3G – Level A and Level B
YCbCr, YCbCr+A, RGB, RGB+A
1080p/ 60, 59.94, 50
1080p/ 30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 25sF, 24sF, 23.98sF
1080i/ 60, 59.94, 50
MD-HDSDIx2 – Two-channel HD-SDI Input Module with switched output
525i, 625i/50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29, 30
1080i/50, 59.94, 60
Page 7
7
MAIN MENU AND NAVIGATION
Access the main menu by pushing and holding the MENU button on the front panel of the monitor.
•Step through menu items using the ▲ and ▼ buttons.
•Choose a submenu or select a menu item by pressing SELECT.
•Return to the previous menu by pressing MENU.
•Exit the main menu by pressing MENU. The menu will automatically time out after 15 seconds.
VIDEO CONFIGURATION SUBMENU
.
■
Color Temperature
Use this setting to choose one of three color temperature presets:
• D55 (5500K)
• D65 (6500K)
• 9300K
• USER (Adjustable Color Bias and Gain)
• Linear (No processing is applied to the panel)
Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale picture.
■
RGB Bias and Gain
Select this submenu to fine-tune the monitor’s color balance (R, G, B). This should only be done by someone experienced with video engineering, as this will alter the
overall color shading of the screen. The purpose is to allow color matching to other types of monitors and/or displays. Note: The Color Temperature preset will
automatically switch to USER when Color Bias settings are adjusted. It is normal for color bias adjustments to be very subtle.
When selecting the RGB Bias and Gain submenu, gain adjustment indicators will appear at the top of the screen, and bias adjustment indicators will appear at the bottom
of the screen:
Use the ▲ and ▼ buttons to select each individual bias or gain control. Press SELECT to begin adjusting the control. Use the ▲ and ▼ buttons to increase or decrease the
value.
RGB Bias and Gain
Page 8
8
Alternately, the image adjustment buttons (Brightness, Color, Tint, Contrast) can be used to easily adjust the bias and gain settings as shown belo w. The buttons affect
whichever row of controls (gain or bias) is currently selected.
■
Check Field
Use the check field modes for monitor calibration or to analyze individual color components of an image. In Monochrome mode, all color is disabled and only a grayscale
image is shown. In Blue, Green, and Red check field modes, only the selected color will b e shown.
Use the following procedure when calibrating the monitor to SMPTE color bars with the following procedure:
1. Allow the monitor to warm up for at least 5-10 minutes.
2. Display SMPTE split-field color bars on the monitor using an external source.
3. Enable Monochrome mode.
4. Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of th e screen. Adjust the Brightness button until there is no visible
difference between the super black and black bars, but the gray bar is still visible.
5. Adjust the Contrast button until an even grayscale appears along the top bars.
6. Disable Monochrome mode.
7. Enable Blue Check Field mode and adjust the Color button so that the outermost bars (white and blue) appear to match in brightness.
8. Composite NTSC only: Adjust the Tint button until the third bar from the left (cyan) and the third bar from the right (magenta) appear to match in brightness.
9. Disable Blue Check Field mode.
■
Ratio Settings
Use to switch between Full Screen, 4:3 and 16:9 aspect ratios.
• In Full Screen mode, images are scaled to fill the entire screen.
• In 4:3 mode, images are scaled to fill the center 4:3 portion of the screen. With a 16:9 source, images will be centered with a black letter-box added on the left and
right sides.
• In 16:9 mode, images are scaled to a 16:9 portion of the screen , with a black letter-box added top and bottom.
Note: The aspect ratio setting is ignored when Pixel-to-Pixel mode is enabled.
■
Pixel-to-Pixel
Use this setting to enable Pixel-to-Pixel mode.
This Pixel-to-Pixel mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and aspect ratio, with a one-to-one
mapping:
• For incoming formats smaller than the native resolution of the LCD panel, the image will be displayed in the center of the screen using only the necessary LCD pixels.
For example, NTSC images will occupy exactly 720 x 480 pixels. The surrounding pixels will be black.
Note: Pixel-to-Pixel mode disables aspect ratio control and H/V Delay.
MARKER CONFIGURATION SUBMENU
Use the Video Configuration submenu to select various video settings such as monochrome mode or blue-only mode.
Page 9
9
■
Marker Enable
Use this setting to enable or disable all on-screen markers. This setting affects the center marker, full screen markers, 16:9 markers and 4:3 markers.
■
Center Marker
Use this setting to display a center marker on the screen.
■
16:9 Markers
Use these settings to superimpose one of 12 markers on the screen wh en in 16:9 mode.
4:3
13:9
14:9
1.85:1
2.35:1
95% Safe
93% Safe
90%Safe
88% Safe
85% Safe
80% Safe
16:9 Marker Examples:
■
Full Screen Markers
Use these settings to superimpose one of 6 markers on the screen when in Full Screen mode.
95% Safe
93% Safe
90%Safe
88% Safe
85% Safe
80% Safe
■
4:3 Markers
Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode.
• 95% Safe Area
• 93% Safe Area
• 90% Safe Area
• 88% Safe Area
• 85% Safe Area
• 80% Safe Area
4:3 Marker Examples:
Marker ConfigurationSubmenu
90% Safe Area
OFF (No Marker)
4:3 Aspect Ratio Marker
2.35:1 Aspect Ratio
OFF (No Marker)
90% Safe Area
Page 10
10
■
Marker Background
Use this setting to choose how selected markers are displayed on the screen. :
• 0% The marker is superimposed on the complete image.
• 25% Image area beyond the marker is shown at 25% intensity.
• 50% Image area beyond the marker is shown at 50% intensity.
• 75% Image area beyond the marker is shown at 75% intensity.
• 100% Image area beyond the marker is shown at 100% intensity (black).
Example (80% Marker in 4:3 Mode):
0% Background 100% Background
Page 11
11
FILTER CONFIGURATION SUBMENU
■
False Colors
This monitor has a false color filter to aid in the setting of camera exposure. As the camera Iris is adjusted, elements of the image will change color based on the
luminance or brightness values. This enables proper exposure to be achieved without the use of costly, complicated external equipment. To best utilize this feature, you
must understand the color chart below and have a basic understanding of camera exposure. Normally, when shooting subjects like people, it is common practice to set
exposure of faces to the equivalent of approximately 56 IRE. The false color filter will show this area as the color PINK on the monitor. Therefore, as you increase
exposure (open the IRIS), your subject will change color as indicated on the chart: PINK, then GREY, then a few shades of YELLOW. Over exposed subjects (above 101 IRE)
on the monitor will be shown as RED. In addition, underexposed subjects will show as DEEP-BLUE to DARK–BLUE, with clipped-blacks indicat ed with a FUCHSIA-like color.
Lastly, the color GREEN is used to indicate elements of the image that are approximately 45 IRE. This represents a ‘neutral’ or ‘mid-level’ exposure commonly used for
objects (not people).
False Color Key
Page 12
12
■
Mosquito Filter
Use this setting to filter out “Mosquito Noise” – an artifact that appears as specs around edges of objects. This artifact is the result of video that has been compressed at
some point. Video sources from DVD-Players, PDA’s, Digital Cable Boxes, Camcorders, etc. often have this artifact.
SYSTEM CONFIGURATION SUBMENU
Use the Color Configuration submenu to adjust the color temperature of the display.
■
Input Format OSD
Use this option to enable on-screen display of input/format status in the upper-left corner of the screen.
■
Curtain Color
Use this option to change the curtain color on the monitor. This curtain color is what you see when there is no signal input to the monitor.
■
Splash Screen
Use this option to enable or disable the Marshall Electronics Inc. splash screen seen when the monitor is first powered on.
■
Freeze
Use the Freeze function to “freeze” the current image on the screen. Select this menu item again (Unfreeze) to return to the real-time video input.
■
Contrast / Backlight
Use this feature to choose between controlling the Contrast of the image or the intensity of the panel’s Backlight with the CONTRAST button on your monitor. Note:
While the Contrast control moves up and down at intervals of 1, the Backlight control will move up and down at intervals of 2, from 0-100.
■
Load Setup
Select this menu item to reset all adjustments and menu settings to the factory default co nfiguration or to one of the user configured presets.
■
Save Setup
Select this menu item to save a current setup into one of 6 available user presets.
■
Power On Preset
Select this menu item to reset all adjustments and menu settings to the factory default co nfiguration whenever the unit is powered down.
FUNCTION PRESETS SUBMENU
■
Function Presets
Allows user to assign menu items to the front panel function buttons: F1, F2. The following options are available for each button:
Ratio
Check Field
Mosquito Filter
False Colors
Freeze Input
Aspect Markers
Center Marker
Marker Enable
Pixel-to-Pixel
Color ConfigurationSubmenu
Page 13
13
IMD CONFIGURATION
■
Text Enable
Use the Text Enable function to turn the MD Text feature ON. This will cause the Text String to appear on the lower portion of the screen.
■
Text String
Use this field to enter your own 16 character string on the screen.
■
Text Color
Use this field to change the color of the text in the Text String field.
■
Text Background
Use this field to change the opacity of the background behind the text in the Text String field. A value of 0% will cause the background to appear black. A value of 100%
will make the background invisible.
■
Text Alignment
Use this field to change the alignment of the text string mentioned above.
SYSTEM INFORMATION SUBMENU
■
System
This shows the System firmware version of your monitor.
Page 14
14
■ Input (Slot 1)
This shows your module type and the firmware version of your module. If no module is present, the word EMPTY will appear in parentheses.
Page 15
15
Specifications
■ PANEL
Screen Size 17.3” Diagonal
Pixels 1920 x RGB x 1080
Viewing Angle (LR x UD) 160° x 150°
Brightness 300 cd/m2
Contrast Ratio 650:1
■ CONNECTORS
S1 (Module Slot)
For Marshall I/O Modules Only
Cold-Swap – remove power from unit before
Inserting or removing Modules.
Power Input
2-Pin Twist Lock Connector
Tally Hardware Interface
HD-15 Female
CN-1 – Programming Port*
Factory / Upgrade Use Only
■ TALLY Hardware Interface (HD-15)
Activation requires contact closure of pin to ground on the HD-15
connector:
■ ELECTRICAL
Power Consumption 3.5A @ 12VDC (42 W)
Voltage Requirement 12 VDC
■ MECHANICAL
Weight (with rack ears): 8.8 lbs
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature -4°F to120°F (-20°C to 50°C)
See Dimensions section for exact specifications.
. HD-15 Female
Dimensions
Page 16
16
Page 17
17
Page 18
18
This page intentionally left blank
Page 19
19
This page intentionally left blank
Page 20
20
Maintenance
■ Screen Cleaning
Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-fiber cloth can also be used using only non-abrasive and
ammonia-free cleaning agents. Do not use paper towels. Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the
surface. Antistatic and fingerprint resistant cleaning agents are recommended. Do not apply excessive pressure to the screen to avoid damaging the LCD.
■ Faceplate Dusting
Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface, attracting dust particles. Neutralize static electricity
effects by using the recommended cleaning and polishing practice.
Warranty
Marshall Electronics warranties to the first consumer that this V-LCD17HR LCD monitor will, under normal use, be free from defects in workmanship and materials, when
received in its original container, for a period of one year from the purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to
honor the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above.
Therefore, labor and parts may be charged to the consumer. This warranty does not apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or
modifications in design or construction void this warranty. It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of the display
active viewing area. Marshall Electronics reserves the option to refuse service for display pixel failure if deemed unobtrusive to effective use of the monitor by our
technicians. No sales personnel of the seller or any other person is authorized to make any warranties other than those described above, or to extend the duration of any
warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve products and product features, specifications may
change without notice.
Loading...