Marshall Electronics CV350-5XB User Manual

1080 HD-SDI

5X Autofocus Lens Day/Night Camera

CV350-5X (Signal type: 1080P25/30, 1080i50/60, 720P50/60, 1080P50/60)
CV350-5XB (Signal type: 1080P29.97, 1080i59.94, 1080P59.94, 720P59.94)

PRECAUTIONS

Do not use the camera if fumes , smoke or a strange odor is emit ted

!

WARNING



CAUTION



CAUTION



CAUTION



CAUTION



CAUTION



CAUTION

from the unit, or if it seems to no t function correctly. Disconn ect the
power source immediately a nd consult your supplier.

Always follow the instruc tions in the installatio n guide when
applying power. Fire and equi pment damage can occur if powe r
is applied incorrect ly. For the correct power supply, refer to the

Do not install or operate in sm all, unventilated areas. Hea t build up

To prevent damage, do not drop the ca mera or subject it to strong
shock or vibration.

If installed close to a TV, radio transmit ter, magnet, electric motor

interfere with or distor t the image.

Whether or not the camera is used o utdoors, never point it towa rd
the sun. Use caution when operat ing the camera in the vicinit y of spot

Do not use the camera in ex treme environments where h igh
temperatures or high hu midity exists. Use the ca mera under
conditions where temperat ures are between 14°F ~ 122°F (-10°C ~
50°C), and humidity is be low 90%.

REGULATORY NOTICE

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.

FEATURES

Panasonic 2.3 Megapixel CMOS
5x Optical Zoom, F=4mm ~ 20mm, F2.8 ~ F3.9
HD-SDI(BNC), HDMI, and Analog CVBS (BNC)

0.2Lux (Color), 0.1Lux (B/W), 0.005Lux (DSS On)

Optical Multi Coated ICR Filter
3D-DNR, Privacy masking
Defog, HLC, WDR
Full OSD control
12VDC

HARDWARE OVERVIEW: Front SPECIFICATIONS

5x Auto Focus Lens

Remote Control IR Receiver

HARDWARE OVERVIEW: Rear

Analog Video Output

Z/F & Menu
Controls Key

Power Input

12VDC

Remote Control

IR Receiver

Power LED Indicator

1. Alarm output for Motion detection

Hole for wall or
ceiling mount

HD-SDI Video Output

Image Sensor 1/2.86” Progressive CMOS (Approx. 2.3 mega)
Scanning System 16:9 Progr
Sync. System Internal

Sensor

Effec

tive Pixel 1920(H) x 1080(V
Min. Illumination 0.2Lux (Day), 0.1Lux
Horizontal Resolution 1000TVL
Lens 5x Opti
Zoom 5x optical

Optics

Focus Near/Far, Au
Angle of View(H) 64.2 degrees(
Back Light Compensation WDR/BLC, HLC(High Light compensation)
Exposure A

lance Auto(3,0

White Ba

Func

tions

Day & Night System AGC / TDN(ICR)
E

lectronic Shutter NTSC: 1/30~1/30000, PA

Functions Privac

SDI Output

Vi

deo

Output

CVBS (NTSC/ PAL) Analog

HD Output

RS485

Control

D/N input O

Interface

Motion Detection out

Operation Temperature -10℃ ~ 50℃
Power

General

Input 12VDC (7V
Power consumption Max 6W (4.
Weight 274g (0.6L
Dimensions (D x W x H) 53.7 x 36.3 x 34.8mm (2.11 x 1.42 x 1.37")

2. External Day/Night input

HDMI Video Output

3. GND

4. RS-485 Remote control: -

5. RS-485 Remote control: +

DIMENSIONS

Z/F & Menu Controls Key

MENU On, One Push AF Key

Menu On: Press and hold menu key for 2seconds to display menu.
Menu Mode: To select data or exit from menu, press menu key.
One Push AF: To adjust focus position, press and release menu key when One Push AF mode is enabled.

Focus NEAR: Press and hold right key for continuous optical focus near.
MENU: To change menu parameter, press right key while menu is displayed.

Focus Far: Press and hold left key for continuous optical focus far.
MENU: To change menu parameter, press left key while menu is displayed.

Zoom TELE: Press and hold up key for continuous optical zoom in(Tele).
MENU: To move up menu item, press up key while menu is displayed.

Zoom WIDE: Press and hold down key for continuous optical zoom out(Wide).
MENU: To move down menu item, press down key while menu is displayed.

Design and specifications are subject to change without notice.

essive

)

(Night), 0.005Lux(DSS on)

cal Zoom, F=4.0~20mm, F2.8 ~ F3.9

zoom + 12x digital zoom = 60x

to/Manual/One Push

WIDE), 13.8 degrees(TELE)

uto / Manual

00°K~8,000°K) / ATW(1,900°K~11,000°K) / Manual

y Mask, Image Mirror, 3DNR, Flicker-less, Sharpness, Defog

SMPTE 292M(1.485Gbps): 1080P@29.97, 720P@59.94
SMPTE 424M (

800mVp-p, 75Ω, unb

Composite(1V ± 0.2 Vp-p) NTSC/PAL
HDMI 1920x1080p@59.94, 1920x1080i@59.94,
1920x1080
PELCO-P/D, SONY-VISCA protocol

8bits data, 1 stop bit, no parity, 2400~115200bps

loating): Day mode, CLOSE: Night mode

PEN(f
High level signal(5VDC) output.
MD output use tr

L: 1/25~1/30000, DSS( ~ 1/1sec)

2.97Gbps): 1080P@59.94

alanced generator(single-ended)

p@29.97, 1280x720p@59.94

ansistor, connect lower than 100mA load.

to 15VDC)
8W Lens inactive, 5.5W Lens active)

bs)

Setup Menu of 1080 HD-SDI 5X Auto Focus Camera

SETUP SUB MENU SUB MENU DESCRIPTION

Connuously adjusts camera color balance in accordance with any change in color temperature. Compensates for color temperature changes within the range of

Color temperature will be manually adjusted by pushing the OSD buon. Place the white paper in front of the camera when OSD buon is pressed to obtain the

Select this to fine-tune White Balance manually. You can adjust the blue and red tone level manually.

Select one according to the locaon of camera installaon. Then, select one sub-mode from AUTO, MANUAL, SHUTTER, PRIORITY, IRIS PRIORITY, and BRIGHT.

IRIS and SHUTTER are controlled automacally.

IRIS, GAIN, and SHUTTERf are controlled manually.

Manual IRIS and GAIN control with automac SHUTTER control.

IRIS and GAIN can be controlled by control of BRIGHTNESS.

0~20: Adjust the screen brightness. MANUAL: BRIGHTNESS control is fixed, and give the exposure control priority to other resources.

0~20: Adjust the IRIS screen brightness. AUTO: IRIS controls exposure automacally but SHUTTER is fixed. MANUAL: IRIS control is fixed, and give the exposure

1/2~40K: Adjust the SHUTTER speed. (1/2, 4, 8, 15, 30, 60, 90, 120, 150, 180, 2 50, 350, 500, 725, 1000, 1500, 2K, 3K, 4K, 6K, 10K, 20K, 30K, 40K)

OFF~1/2: Adjust the level of DSS. (OFF, 1/30, 1/15, 1/8, 1/4, 1/2) When it is in low luminance condion, DSS can adjust the picture quality by maintaining the light

Automacally adjusts the focus posion.

Manually adjusts the focus posion when zoom is changed.

When this mode is enabled, it will automacally adjusts the focus posion only when the zoom is changed.

Set the limit of the tele.

Set the limit of the wide.

AUTO: The focus is automacally adjusted at the pre-set interval (01~07). ONE PUSH: The focus is re-adjusted when the OSD buon is pushed over ONE PUSH.

This funcon is to set user defined zoom and focus posion. Up to 32 preset posion can be set with sub menu, USER PRESET, ACTIVE, SAVE, RESET.

The camera will stay in DAY in a normal environment, but switched to NIGHT mode when ambient illuminaon become this pre-set level.

This feature will observe the object movement by moon zone and sensivity that are pre-set with sub menu, DET. SIZE, SENSITIVITY, MASK ACTIVE, WIDTH,

Change video output specificaon. CV350-5X: 1080P25/30, 1080i50/60, 72 0P50/60, 1080P50/60. CV350-5XB: 1080P29.97, 1080i59.94, 1080P59.94, 72 0P59.94

Mask an area you want to hide on the screen with sub menu, MASK NO, MASK ACTIVE, MASK COLOR, WIDTH, HEIGHT, MOVE HOR, MOVE VER, TRANS, RESET

EXIT Exit the setup.

AWB Controls the automac adjustment of the light source's color temperature to 3,000°K ~ 8,000°K.
ATW

WB

CONTROL

AE

CONTROL

(EXPOSURE)

FOCUS

CONTROL

BACK LIGHT

IMAGE

CONTROL

DISPLAY

CONTROL

RESET Re

PUSH

INDOOR Select this when the color temperature is between 4500K and 8500K.

OUTDOOR Select this when the color temperature is between 1700K and 11000K (Ex. Sodium light inclusion)

MANUAL BLUE, RED

INDOOR, OUTDOOR

BRIGHTNESS MANUAL, 0~20

IRIS AUTO, MANUAL, 0~20

AGC LIMIT 0~20 A funcon which controls the amplificaon/gain process automacally if the illuminaon falls under the usable level.

SHUTTER AUTO, MANUAL, 1/2~40K

DSS(SENS-UP) MANUAL, OFF~1/2

FLICKERLESS OFF, ON Use this funcon when you experience picture flicker, this happens when there is a conflict with the installed lighng frequency.

FOCUS MODE

ZOOM SPEED 0~7 Set the zoom speed.

TELE LIMIT X3~X60

WIDE LIMIT X1~X2

FAR END INFINITY, 2, 3, 5, 10M Set the distance limit for the far focusing. The lens moves to adjust the focus from the distance.

NEAR END 30CM, 1, 1.5, 2, 3, 5, 10M Set the priority distance limit for near focusing.

LENS INITIAL OFF, AUTO, ONE PUSH

USER PRESET

WDR/BLC

ACE GAIN Brightness correcon of the dark image area. Adjust the GAIN level (LOW, MIDDLE, HIGH).

ECLIPSE

AUTO

DAY The picture is always displayed in color.

IGHT N

N

EXT

COLOR LEVEL 0~20 Adjust the color level value for a fine

SHARP

NESS 0~20 As you increase this value, the picture outline becomes stronger and clearer.

IMAGE FLIP Video output will be flipped (MIRROR-HORIZONTALLY, FLIP-VERTICALLY, ROTATION).

DEFOG AUTO, MANUAL This feature will help increase visibility in extreme weather condions, such as fog, rain or in a very strong luminous intensity.

3D-DNR OFF, LOW, MIDDLE, HIGH This feature will reduce the video

M

OTION

SHADING This feature will correct the inconsistent brightness level in the image.

GAMMA This feature will adjust video output brightness (STANDARD, STRAIGHT, LOW, MIDDLE, HIGH).

RESOLUTION

USER TITLE The camera tle can be entered and it will appear over the video o utput.

ZOOM MAGNIFICATION Turn On or off of the zoom scale display.

PRIVACY

ADDRESS 0~255 Select the camera ID number.

ADDRESS DISPLAY OFF, ON Select the display of camera ID.

BAUDRATE Set the baudrate of RS-485 comm unicaon (2400, 4800, 9600, 19200, 38400, 57600, 115200).
LANGUAGE You can select the menu language according to your requirements. ( ENGLISH, 简体, FRANÇAIS, DEUTSCH, ESPAÑOL, PORTUGUÊS, РУССКИЙ)
DEFECT ADJ Defecve pixels can be corrected.

VER. Display the firmware version.

AUTO

MANUAL

SHUTTER PRIORITY Manual SHUTTER and GAIN control with automac IRIS control.

IRIS PRIORITY

BRIGHT

AUTO

MANUAL

PUSH

WDR Enable user to view both object and background more clearly when background is too bright. Set the WDR-LEVEL (0~4).

BLC Enable a back light compensaon feature.

SPOT Enables a user to select a desired area on a picture and view that area more clearly when background is too bright.

LEVEL Highlight the bright

COL

OR Select the color for masking (GRN, MAG, RED, BLUE, BLK, WHT, YEL, CYN)

D/N LEVEL

MARGIN Set the margin between Day →Night switching level and Night →Day switching level. Different exposure gain level is needed to avoid malfuncons.

DWELL TIME Select the checking me of light condion to confirm to chage from the day mode to the night mode.

NIGHT BURST Night burst OFF makes that the color burst is removed when ICR switches to black/white.

IGHT BURST The picture is always displayed in black/white.
D/N LEVEL The camera will stay in DAY in a normal environment, but switched to NIGHT mode when ambient illuminaon become this pre-set level.

DWELL TIME Select the interval me from the day mode to the night mode.

NIGHT BURST Alters the color burst informaon passed to the video monitor.

area with a masking box with a selected color. Adjust the masking level (0~20).

color tune.

noise at low ambient light.

set the camera sengs to the factory defaults.

Design and specifications are subject to change without notice.