Page 1
Broadcast A/V Division
CV226
Lipstick HD Camera
3G/HD-SDI
User Manual
[Firmware Version 0.43]
Page 2
CV226 Manual
Table of Contents
1. General Information
2. Menu Structure
3. WB CONTROL
4. AE CONTROL
5. BACK LIGHT
6. IMAGE STABILIZER
7. IMAGE CONTROL
8. DISPLAY CONTROL
9. RESET
10. TROUBLESHOOTING
11. WARRANTY
02
03
05
06
07
08
09
10
11
12
13
1. General Information
Thank you for your purchase of a Marshall Miniature or Compact Camera.
The Marshall Camera team recommends thoroughly reading this guide for a deep understanding
of on-screen-display (OSD) menus, breakout cable operation, settings adjustment explanation,
troubleshooting, and other critical information.
Please carefully remove all contents of box, which should include the following components:
CV226 includes:
• Camera with breakout cable (Power/RS485/Audio)
• 12V Power Supply
The CV226 Camera utilizes an all-weather rated body with IP67 rated CAP that can be removed
(rotate counter-clockwise) to reveal M12 lens which also can be rotated to adjust fine-focus
position of lens on lens mount. Also, can be swapped out with other M12 lenses containing
specific focal lengths to change AOV.
Each camera comes set to default at 1920x1080p @ 30fps out of the box, which can be changed
in the OSD Menu to a variety of resolutions and framerates.
If the camera is accidentally changed to a resolution or framerate that your monitor or equipment
does not accept, please follow the instructions below to reset camera to factory default:
1. Plug the camera into power source and connect breakout cable to rear camera panel
(locking connection), Power LED should illuminate.
2. Push OSD joystick button UP, DOWN, UP, DOWN and PUSH and HOLD for five seconds.
3. Camera should reset to 1920x1080p @ 30fps.
4. If camera does not reset, repeat steps after a power-cycle.
www.marshall-usa.com1 2
Page 3
2. Menu Structure
CV226 Manual
Setup Sub Menu Sub Menu
WB CONTROL
AE CONTROL (EXPOSURE)
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
AUTO
ATW
PUSH
COLOR TEMPERATURE
MANUAL
AUTO BRIGHTNESS 0~20
MANUAL AGC LIMIT 0~20
SHUTTER
FLICKERLESS DEBLUR
DSS OF F, X 2~ 32
BACK LIGHT
ACE LOW, MIDDLE, HIGH
ECLIPSE
RANGE 10%, 20%, 30%
FILTER LOW, MIDDLE, HIGH
AUTO C OFF, HALF, FULL
COLOR LEVEL 0~20
SHARPNESS 0~20
MIRROR ON, OFF
FLIP ON, OFF
D-ZOOM 1.0X ~ 16.0X
DEFOG
DNR
MOTION
SHADING
BLACK LEVEL
GAMMA
FRAME RATE
SHUTTER
OFF, LOW, MIDDLE, HIGH
DET WINDOW
SENSITIVITY 0~20
MOSTION
OSD
RED GAIN
BLUE GAIN
NORMAL
WDR
BLC
SPOT
LEVEL
COLOR
AUTO
MANUAL
ON, OFF
0~10 0 %
0~32
0.3~0.8
Setup Sub Menu Sub Menu
DISPLAY CONTROL
RESET ON/CHANGE USER/FACTORY
EXIT
CAM VERSION
CAM TITLE
PRIVACY
CAM ID 0~255
BAUDR ATE 2400~115200
LANGUAGE ENG, CHN
DEFECT DET
www.marshall-usa.com3 4
Page 4
CV226 Manual
3. WB CONTROL
Select WB CONTROL using the UP or DOWN button. You can change between AUTO, ATW, PUSH,
and MANUAL using the LEFT or RIGHT button
MENU WB CONTROL
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
• AUTO: Controls the automatic adjustment of the light source’s color temperature to 3,000 ~
8,000°K.
ATW
OFF
ON
COLOR TEMP
RED GAIN
BLUE GAIN
RETURN
MIDDLE
32
32
4. AE CONTROL
Select AE CONTROL using the UP or DOWN button. You can select the AUTO, MANUAL, SHUTTER,
or FLICKERLESS mode from the sub menu.
MENU AE CONTROL
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
• MODE: Select the desired exposure mode.
» AUTO: Exposure level is automatically controlled.
ATW
OFF
ON
MODE
BRIGHTNESS
AGC LIMIT
DSS
RETURN
AUTO
10
13
AUTO
OFF
• ATW : Continuously adjusts camera color balance in accordance with any change in color
temperature. Compensates for color temperature changes within the range of 1,900 ~
11,000°K.
• PUSH: Color temperature will be manually adjusted by pushing the OSD button. Place the
white paper in front of the camera when OSD button is pressed to Obtain the optimum result.
• MANUAL: Select this fine-tune White Balance manually.
You can adjust the blue and red tone level manually.
» COLOR TEMP: Select color temperature from LOW, MIDDLE, or HIGH.
» BLUE GAIN: Adjust the Blue tone of the image.
» RED GAIN: Adjust the Red tone of the image.
Adjust White Balance first by using the AUTO or ATW mode before switching to MANUAL mode.
White Balance may not work properly under the following conditions. In this case, select the ATW
mode.
• When the ambient illumination of the subject is dim.
• If the camera is directed towards a fluorescent light or is installed in place where illumination
changes dramatically, White Balance operation may become unstable.
» MANUAL: Adjust BRIGHTNESS, GAIN, SHUTTER, and DSS manually.
» SHUTTER: Shutter can be set manually and DSS is controlled automatically.
» FLICKERLESS: Shutter and DSS is controlled automatically.
• BRIGHTNESS: Adjust the brightness level.
• AGC LIMIT: Controls the amplification/gain process automatically if the illumination falls under
the usable level.
Camera will raise up the gain to the selected gain limit under dark conditions.
• SHUTTER: Controls the shutter speed.
• DSS: When luminance condition is low, DSS can adjust the picture quality by maintaining the
light level. Slow shutter speed limited to x32.
www.marshall-usa.com5 6
Page 5
CV226 Manual
5. BACK LIGHT
Select BACK LIGHT using the UP or DOWN button. You can select the BACK LIGHT, ACE, or
ECLIPSE mode from the sub menu.
MENU BACK LIGHT
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
• BACK LIGHT: Allows the camera to adjust the exposure of the entire image to properly
expose the subject in the foreground.
ATW
OFF
ON
BACK LIGHT
ACE
ECLIPSE
RETURN
WDR
LOW
ON
6. IMAGE STABLIZER
Select IMAGE STABILIZER using the UP or DOWN button. You can select the RANGE, FILTER, and
AUTO C from the sub menu.
MENU IMAGE STABLIZER
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
• IMAGE STABILIZER: Reduces image blurriness due to vibration caused by hand shake or
camera movement. The image will be digitally zoomed in to compensate the shifted pixels.
ATW
OFF
ON
RANGE
FILTER
AUTO C
RETURN
30%
MIDDLE
FULL
» WDR: Enables user to view both object and background more clearly when background is
too bright.
» BLC: Enables a back light compensation feature.
» SPOT: Enables a user to select a desired area on a picture and view the area more clearly
when background is too bright.
• ACE: Brightness correction of the dark image area.
• ECLIPSE: Highlight the bright area with a masking box with a selected color.
» RANGE: Set the digital zoom level for image stabilizing. Max 30% = x1.4 Digital Zoom.
» FILT ER : Select the level of correction hold filter for the worst case of image. High = Less
Correction.
» AUTO C: Select the image auto centering level according to a vibration type. Full = Severe
Vibration, Half = Minor Vibration.
www.marshall-usa.com7 8
Page 6
CV226 Manual
7. IMAGE CONTROL
Select IMAGE CONTROL using the UP or DOWN button. You can adjust all image related features
from the sub menu.
MENU IMAGE CONTROL
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
OFF
ON
COLOR LEVEL
SHARPNESS
MIRROR
FLIP
D-ZOOM
DEFOG
DNR
MOTION
SHADING
BLACK LEVEL
GAMMA
FRAME RATE
RETURN
15
10
OFF
OFF
1.0X
OFF
LOW
OFF
OFF
0
0.55
HD1080p60
8. DISPLAY CONTROL
Select IMAGE STABILIZER using the UP or DOWN button. You can select the RANGE, FILTER, and
AUTO C from the sub menu.
MENU AE CONTROL
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
• CAM VERSION: Display the camera firmware version.
ATW
OFF
ON
RANGE
FILTER
AUTO C
RETURN
30%
MIDDLE
FULL
• COLOR LEVEL: Adjust the color level value for a fine color tune.
• SHARPNESS: Adjust the image sharpness for a smooth or a sharp edge expression.
• MIRROR: Video output is rotated horizontally.
• FLIP: Video output is rotated vertically.
• D-ZOOM: Digitally zoom the video output up to 16x.
• DEFOG: Increases the visibility in extreme weather conditions, such as fog, rain or in a very
strong luminous intensity.
• DNR: Reduces the video noise at low ambient light.
• MOTION: Observes the object movement by motion zone and sensitivity that are pre-set with
sub menu. The motion detection icon can be displayed.
• SHADING: Correct the inconsistent brightness level in the image.
• BLACK LEVEL: Adjusts video output black level in 33 steps.
• GAMMA: Adjusts video output gamma level in 33 steps.
• FRAME RATE: Change video output specification.
• CAN TITLE: Camera title can be entered using the virtual keyboard and it will overlay on the
video.
• PRIVACY: Mask areas where you want to hide on the screen.
• CAM ID: Select camera ID number from 0~255.
• BAU DRATE : Set the camera baudrate of RS-485 communication.
• LANGUAGE : Select English or Chinese OSD menu.
• DEFECT DET: Adjust the active pixels by adjusting the threshold value.
Camera lens must be completely covered before activating this menu.
Select the FRAME RATE using the LEFT or RIGHT button. Available frame rates are:
720p25, 720p29 (720p29.97), 720p30, 720p50, 720p60, 1080p25, 1080p30, 1080i50, 1080i60,
1080p50, 1080p60. 720p59 (720p59.94), 1080p29 (1080p29.97), 1080i59 (1080i59.94), and 1080p59
(1080p59.94)
www.marshall-usa.com9 10
Page 7
CV226 Manual
9. RESET
Select RESET using the UP or DOWN button. You can reset the setting to FACTORY or USER saved
settings. Choose ON or CHANGE by using the LEFT or RIGHT button.
MENU RESET
WB CONTROL
AE CONTROL
BACK LIGHT
IMAGE STABILIZER
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
• ON: Set the camera reset setting to either FACTORY or USER saved settings which is defined
from CHANGE menu.
ATW
OFF
ON
RESET MODE
SAVE
RETURN
USER
ON
10. TROUBLESHOOTING
Problem Solutions
Nothing appears
on the screen.
The picture is not
clear.
The picture has
interference.
a. Check that all connected devices are powered on.
b. Confirm that the voltage is correct.
c. Confirm that the power supply provides enough current to power the
camera.
d. Check that all video cables are correctly connected.
a. Check that your monitor is correctly adjusted.
b. Confirm that the glass in front of the lens is clean. If there is dust, dirt,
or fingerprints on the glass, the image quality will be affected. To clean
the glass, use a soft, dry, and non-abrasive cloth or a commercially
available lens cleaning set.
c. Correctly adjust the focus.
a. The camera may be close to a high voltage source, such as a power
generator.
b. The BNC cable is not terminated properly.
c. The video cables are not connected properly.
Please make sure to select the right mode before resetting the camera.
• CHANGE: Change reset mode or save the current setting as a USER.
» FACTORY: Select FACTORY if factory default setting is needed. FRAME RATE, CAM ID,
and BAUDRATE will not change.
» USER: Select USER if the USER saved setting needs to be loaded.
» SAVE : Save the current settings as the USER saved setting.
The picture
is flickering
continually.
The camera is
not synchronizing
with the reference
signal.
a. Check the termination and set the impedance at 75Ω properly.
b. Ensure that the camera is not pointing towards the Sun or any light
source.
c. Check if there is any intermediate device.
d. Check if the distance of the video cable exceeds the maximum
transferable limitation.
a. Make sure Tri-Level reference signal is used.
b. Locking takes up to 1 minute depending on the signal strength. Make
sure the sync LED is solidly lit.
c. Check if the cable and connectors used in reference sync are in good
condition.
d. Make sure the cable length used in reference sync does not exceed 100
ft.
e. Make sure OUTPUT EN is on when using the genlock output.
www.marshall-usa.com11 12
Page 8
Warranty
Marshall Electronics warranties to the first consumer that this device will, under normal use,
be free from defects in workmanship and materials, when received in its original container, for
a period of two years from the purchase date. This warranty is extended to the first consumer
only, and proof of purchase is necessary to honor the warranty. If there is no proof of purchase
provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty
set forth above. Therefore, labor and parts may be charged to the consumer. This warranty
does not apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or
modifications in design or construction void this warranty. No sales personnel of the seller or
any other person is authorized to make any warranties other than those described above, or to
extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period
described above.
Due to constant effort to improve products and product features, specifications may change
without notice.
20608 Madrona Avenue, Torrance, CA 90503
Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688
www.marshall-usa.com
support@marshall-usa.com
V.1. 2
Loading...