V-RD151-
Users Guide
9
Alternate Menu Functions
Menu is shown by holding down ALT and then pressing the
MENU button. (ALT+MENU). Function selection and cursor
movement is performed with the source selection buttons.
CH1 - ID Input 5 character
label for each source
CH2 - Date/Time Setup
CH3 - Sequence (Off to30 Second) Changes displayed image at programmed
intervals when SEQN function is selected
CH4 - Miscellany. PIP FORMAT- position and number of PIP windows.
DATE/TIME-CH DISPLAY - Characters are displayed on the screen over video images.
* NOTE: Date/Time and Channel Display overlay is not available in PC ANALOG or S-VIDEO modes
10
Analog PC Menu Functions
System Menu in Analog PC Mode
Menu Selected
Marshall Electronics
1910 East Maple Ave.
El Segundo, CA 90245
Tel.: 800-800-6608 • Fax: 310-333-0688
www.LCDRacks.com
Email: sales@lcdracks.com
V-RD151-44
Users Guide
* Note: When in PC Analog mode to change the source press the SELECT
button with no OSD is displayed on screen
System Display in Pixels and Frequency
PC Display Position Adjust
(Not available in Composite or S-Video mode)
PC Image Phase and Clock Adjust
(Not available in Composite or S-Video mode)
PC Input Automatic Configuration
(Auto config requires signal to be present
on VGA connector)
11
Warranty
Marshall Electronics warranties to the first consumer, that this V-RD151-4 rackmount monitor will, under normal use, be free from defects in workmanship
and materials, when received in its original container, for a period of one year from the purchase date.
This warranty is extended to the first consumer only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with
a warranty claim, Marshall Electronics reserves the right, not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above,
or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.
Due to constant effort to improve products and product features, specifications may change without notice.
Product Overview
Features
Electrical Specifications
Mechanical Specifications
Installation
Input Connectors
Switch Settings and Indicators
Primary Menu Functions
Volume adjustment does not function •
Displayed source selection •
MODE adjustment does not function •
System Functions •
System Reset •
OSD Timeout •
OSD Position •
System Info •
Contrast, Color, Brightness Adjust •
Alternate Menu Functions
Analog PC Menu Functions
System Menu in Analog PC Mode •
PC Display Position Adjust (Not available in Composite or S-Video mode) •
PC Input Automatic Configuration •
Warranty
1
2
3
4
5
6
7
8
9
10
11
1
Product Overview
The V-RD151P-4 is space saving monitor in a drawer with a high-resolution 1024 × 768 pixel 15” display.
This model also features a Quad Split and Sequential Switcher for composite video signals. The Quad Split
feature allows any mix of the four composite video channels to appear on the monitor as real time picturein-picture images. For added flexibility, this unit can accommodate composite video, Y/C (S-Video) or XGA
computer signals for monitoring (S-Video and XGA inputs are only available in full screen mode). All connections are accessed from the rear of the drawer enclosure and include a loop through for each signal.
When the display is closed into the drawer, the monitor will automatically be placed into standby mode and
a keyed lock is provided for secure transport. V-PS12-5V-1 Power supply and owners manual are included.
2
Features
MODE adjustment does not function
System Functions
RESET - resets the monitor to factory defaults.
TV - does not function on this model
OSD TIMEOUT- Adjust timeout of menu display. OSD - (On Screen Display)
OSD POSITION-
SYSTEM INFO- Displays system confi guration information
adjust placement of OSD
High Resolution 1024 × 768 pixels, 786,432 total
Bright 250 candle luminance
4 Video inputs with 75Ω termination and active loop through feature
Ultra-compact design fits in EIA standard rack 1U high
Built-in Quad Splitter/Sequential Switcher
Available in NTSC or PAL format
Key lock for secure transportation
3
Electrical Specifications
Display (Viewing Area) 15.1” (11.69”H × 9.12”V) (29.7cm × 23.1cm)
Viewing Angle 170
Resolution (Dots) 1280H × 768V / 2.95 million pixels
Dot Pitch 0.297mm × 0.302mm
Number of Colors 16.7 Million
Brightness (in cd/m²) 250 cd/m²
Contrast Ratio 500:1
System NTSC - V-RD151-4
Inputs Composite-BNC 75W, Y/C (S-Video)-4 Pin Mini-din Female,
Outputs Composite Active Loop-BNC, SDI Active Loop-BNC,
Power required 12VDC, 5.0Amps peak
4
Mechanical Specifications
V-RD151-4 Dimensions 19.12”W × 1.75 “H × 22”D (48.5cm × 4.5cm × 55.8cm)
V-RD151-4 Approx. Weight 24.15 lbs (10.94kg)
V-PS12-5V-1Power Supply Weight 1 lbs (0.45kg)
5
Installation
0
In any direction
PAL - V-RD151-4-PAL
Scalable XGA HD-15 Female,
12VDC-Conxall Female
Y/C (S-video) Active Loop-4 Pin Mini-din Female, 10-bit D/A out-BNC
System Reset
OSD Timeout
OSD Position
System Info
SELECT
Menu Control
SELECT
Menu Control
SELECT
Menu Control
SELECT
Menu Control
SELECT
Menu Control
SELECT
Menu Control
1. The V-RD151-4 includes the following items:
1. V-RD151-4 Drawer Monitor Assembly
2. 2 Drawer Lock Keys
3. 2 Adjustable Rear Support Brackets
4. 4 Rear Bracket Thumb Screws
2. 2. Unpack the V-RD151-4, mounting hardware and accompanying V-PS12-5V1 power supply.
Physically inspect for any damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.
2
V-RD151-4 USERS GUIDE
Contrast, Color, Brightness Adjust
Contrast Color Brightness No Function
Marshall Electronics
5
3. After inspection, attach adjustable rear support brackets using the supplied thumbscrews and install the
V-RD151-4 in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is
required when installed to prevent possible damage to the internal components.
Attached bracketThumbscrews and
rear support bracket
4. Connect required cables for signal input and output.
Note: All BNC connectors should be rated for 75Ω.
Note: Power must be applied to the V-RD151-4 to activate loop through video connections
5. Plug the V-PS12-5V1 power supply into the A.C. source.
6. Attach the twist lock Conxal power connection from V-PS12-5V1 power supply to the back of the drawer.
7. Completely Slide the V-RD151-4 out from the drawer and tilt to your desired viewing angle.
8. Turn on the V-RD151-4 by depressing the power switch located on the front of the unit.
6
Input Connectors
VGA IN
HD-15
(FEMALE)
Pin1-Red IN
Pin2-Grn IN
Pin3-Blu IN
Pin4-
Pin5-
Pin6-Gnd
Pin7-Gnd
Pin8-Gnd
Pin 9Pin10Pin11Pin12Pin13Pin14-HSync
Pin15-VSync
S-Video IN
4 Pin Din
(Female)
Pin1 - GND
Pin2 - GND
Pin3 – Y in
Pin4 – C in
S-Video OUT
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 – Y in
Pin4 – C in
Composite
Video IN 1 to 4
Active Composite
Video out 1 to 4
12 VDC from
V-PS12-5V1 power
supply
Left Pin - Pos
Right Pin- Neg
* All Outputs Require Power to be applied for activation
Marshall Electronics
3
7
Switch Settings and Indicators
Drawer close interlock micro-switch places
monitor into standby mode when in stored position
AB
* NOTE: Digital Process Control is not available in PC ANALOG or S-VIDEO modes
A. Digital Process Controls
(DPC)-not available in PC or S-Video Modes
Quad - 4 channels displayed simultaneously on the screen.
PIP - Picture in Picture menu selected display of 2 to 4 channels.
Zoom - expands a selected portion of the display
Freeze - of full screen image
SEQN - menu selected channel display for 2 to 4 channels of full screen
image. Sequence switching can be set for 1 to 30 second intervals.
MENU - enables alternate menu
ALT - shift control for selection of highlighted functions
B. Composite Video Controls
Selection for full frame viewing of composite video channels 1 to 4.
Also used for Cursor controls of alternate menu functions.
Illuminates when channel is selected.
C
Displayed source selection
C. Primary Menu Controls
Power On/Off selection switch illuminates when monitor is switched on.
Primary Menu Functions
Primary menu functions are accessed by pressing the MENU button.
Volume adjustment
does not function
SELECT
Menu Control
8
PC Analog - Selects input from the HD15 VGA IN connector.
Image is full screen. No DPC functions
Composite - Selects input of composite video 1 to 4 plus DPC functions
S-VHS - Selects input from the
S-VIDEO IN connector. Image is
full screen. No DPC functions
Television - does not function on this model
4
V-RD151-4 USERS GUIDE
Loading...