Page 1
V-R82DP-HDA
Users Guide
SDI: 525i/60hz 4x3
OSD
Use SELECT to enable the On Screen Display
for input and function status
Marshall Electronics
1910 East Maple Ave.
El Segundo, CA 90245
Tel.: 800-800-6608 • 310-333-0606
Fax: 310-333-0688
www.LCDRacks.com
Email: sales@lcdracks.com
Blue Only
SELECT to adjust SMPTE or split fi eld color bars.
1. Allow monitor to warm up for 5-10 minutes minimum.
2. Display SMPTE color bars on monitor. Turn on off Color with control.
3. Find the PLUGE (superblack, black, and gray bars) at the lower right
of the pattern.
Adjust BRIGHTNESS until there is no difference visible between the superblack and black bars, but is still visible.
4. Adjust CONTRAST control to achieve a balanced gray scale across
top bars.
5. Turn up CHROMA (color level) control until the two outermost bars
(white and blue appear to match in brightness.
6. NTSC Only -Adjust COLOR PHASE (tint or hue) control until the third
bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.
V-R82DP-HDA
Users Guide
10
Warranty
Marshall Electronics warranties to the first consumer, that this V-R82DP-HDA Dual 8.4-inch LCD rack mounted monitor set will, under
normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date.
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof
of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore,
labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time
period described above.
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of
the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to
effective use of the monitor by our technicians.
Due to constant effort to improve products and product features, specifications may change without notice.
8
Product Overview
Features
Video - Screen Formats and Frame Rates
Electrical Specifications
Mechanical Specifications
Operational Setup
Connectors
Switch Settings, Adjustments and Indicators
Menu Functions
Warranty
1
2
3
4
5
6
7
8
9
10
Page 2
1
Product Overview
The V-R82DP-HDA features our Completely Digital TFT-Megapixel™ high defi nition TFT/LCD system with 1.44 million pixels. Analog
signals are digitized using an advanced 10 bit process with 4x over sampling and adaptive 5 line comb fi lter plus exacting color space
conversion. Video is scaled to fi t on screen in the highest resolution using a state of the art LSI that incorporates 6x6 pixel adaptive
motion interpolation with precision Gamma correction. Additional features include Pixel-to-Pixel™ native resolution scaling, setup
memory, Underscan, H/V Delay, adjustable color temperature, and Blue Gun.
2
Features
• TFT-MegaPixel™ totally digital
• Multiple format acceptance for virtually any analog or digital video signal
• Display PC Signals to XGA 1024x768
• ColorMatch Conversion™ with SMPTE/EBU color space emulation of CRT
• Color temperature preset for D65
• HyperProcess™ motion interpolation of interlace images
• On screen display of input status, formats, and menu functions
• Pixel to Pixel™ native resolution display
• Ready to mount – all brackets are factory installed
• Lightweight – 75% lighter than CRT models
• Settings memory restores active state with power off/on cycle
• Underscan plus H & V delay
• Blue only (Blue Gun) for adjustment to SMPTE color bars
• Includes V-PS12-5V-1 Universal power supply (U.L. class 2)
• Three LEDs (Red, Green, Amber) produce 7 different tally indications on each screen
• Dry erase label for each screen
3
Video - Screen Formats and Frame Rates
• 525 –60i / 625 - 50i (Interlaced NTSC/PAL)
• 480P (Progressive)
• 576P (Progressive)
• 720P-50P, 59.94P, 60P, 25P, 29.97P, 30P, 50P, 59.94P, 60P (Progressive)
• 1035i - 59.94i, 60i (Interlaced)
• 1080i x 1920 – 50i, 59.94i, 60i, 23.973P, 24P, 25P, 29.97P, 30P, 24psf, 23.97psf
4
Electrical Specifications
All signal types and frame rates are automatically detected
9
Menu Functions
1. Power On/Off Button
Illuminates Red when system power is present. Illuminates Green when monitor is ON.
2. Source Selection Buttons
Video - Composite NTSC or PAL. Composite video must comply to SMPTE-RS170M.
Images without color burst (Subcarrier) component may not display.
S-Video - Y/C (Luminance + Chrominance) NTSC or PAL.
YPrPb - Analog Component color difference signals for Standard Defi nition (YCrCb) or High Defi nition (YPrPb).
VGA - Analog PC.
DVI - Digital Computer or Video Signals. Includes HDCP for use with HDMI originated signals.
3. Pixel to Pixel Function
As the native LCD displays of the V-R82DP-HD are 800 pixels wide by 600 dots (RGB pixels) high, it is necessary to change the size of
the image to fi ll the whole screen. Pixel to Pixel mode bypasses the enlargement/shrink of this scaling function and displays the native
incoming format.
For 525-NTSC/480P based images, pixel to pixel will appear as a 480x640 (4:3 aspect) or 480x720 (16:9 aspect).
For 625-PAL/576P based images, pixel to pixel will appear as a 576x640 (4:3 aspect) or 576x720 (16:9 aspect).
For 1080 line HD based images, pixel to pixel will appear as cropped 800x600 (4:3 aspect) starting from the center of the
image. 240 lines top, 240 lines bottom, 560 pixels left and 560 pixels right will be cropped.
For 720 line HD based images, pixel to pixel will appear as cropped 800x600 (4:3 aspect) with 60 lines from the top and 60 lines from
the bottom cropped. Horizontally, 240 pixels will be cropped from each edge.
3. Menu Enable and navigation
Access menu functions by selecting the MENU button. Use UP / DOWN to navigate and
SELECT to enable or disable the function
Note: Source selection is disabled when in menu mode.
Color Temperature
D-65 (6500K) - Standard setting recommended by SMPTE and EBU.
Simulates normal daylight conditions.
USER - When activated manual adjustment is performed by selecting
Adj. Color Gain or Adj. Color Bias
Screen Aspect 4:3/16:9 switchable
Display (Viewing Area) 8.4 Inch diagonal (170.4mm w x 127.8mm h)
Viewing Angles 130° H x 120° V
Resolution (RGB Dots) 800H×RGBx600V (1.44 million pixels)
Color Depth 262,000 Colors (6-Bit)
Dot Pitch .213mm square pixel
Contrast Ratio 350:1
Pixel Response 10ms rise/25ms fall
Brightness (in cd/m²) 500 cd/m²
Backlight Field Replaceable CCFL (50,000 hour half life)
LCD Screen Treatments Anti Reflection, Anti Glare, Hardcoat
Estimated MTBF 5 years of 24/7/365 operation
System NTSC/PAL with auto recognition
Inputs (ITR-U601) per screen (BNC)
YPrPb Component (3 BNC)
Composite Video PAL/NTSC auto detect (BNC)
S-Video (Y/C) (4 Pin Mini Din female)
XGA 15Pin HD-15 Female
DVI 27 (Pin DVI-I Female)
Active Outputs (ITU-RBT601) per screen (BNC)
Color temperature D65 and User Adjustment
Color Gamut SMPTE-C/EBU 80% CIE
Luma Linearity Typical +/- 3% with 5 IRE increments (0 to 10 IRE)
Power Required 10.8 to 13.2 VDC
Power Consumption Approx. 40 watt nominal
Operating temperature
Storage temperature
Compliance
RoHS WEE / Environmental
2
Tally (HD-15 Female)
YPrPb Component (3 BNC)
Composite Video PAL/NTSC auto detect
32° F to 120° F (0° C to 50° C)
-4 F to 120° F (-20° C to 50° C)
₠, FCC-Class A, ANSI-63.4 (Certificates on file)
Do not dispose. Return to Manufacturer or Authorized Recycle Facility
V-R82DP-HDA Users Guide
When in adjust mode use UP/DOWN to change values. Use SELECT to cycle RED, GREEN,
and BLUE mode. Exit to the main menu by pressing MENU.
Left Line= Increase of Gain
Center Line = D65 (Default)
Right Line = Decrease of Gain
Level Set-up
SELECT between 7.5 IRE for NTSC signals and 0 IRE for NTSC Japan and PAL signals.
7.5 mode will enable a digital black offset of the onscreen images for improved Blacks.
Color Bar
Use to SELECT internal test signal of full fi eld color bars that is available for confi rmation
of LCD operation. This function will disable input selection until cycled off.
H/V Delay
Use to SELECT display of horizontal and vertical blanking areas.
Not available for all signal types.
Under Scan
Use SELECT to reduce the display area with expansion beyond active video. Note that
the V-R82DP-HDA is factory adjusted to display 100% of active video in standard display
mode. This function is normally used with analog Standard defi nition signals. SDI signals will
display all video with ancillary data appearing to the right of the image.
Right Line= Increase of Bias
Center Line = D65 (Default)
Left Line = Decrease of Bias
Marshall Electronics
7
Page 3
5
Mechanical Specifications
8
Switch Settings, Adjustments and Indicators
Tally Lamps
Dimensions 19.12” w x 7” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)
V-R82DP-HDA Weight 5.5 lbs (2.4 kg)
V-PS12-5V-1 Power Supply Weight 1 lbs (0.45kg)
6
Operational Setup
1. Unpack the V-R82DP-HDA and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have oc
curred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.
If you are not located within the continental United States call +1 310-333-0606.
2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when
installed to prevent possible damage to the V-R82DP-HDA internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R82DP-HDA for all outputs to
be activated. All BNC connectors should be rated for 75Ω.
4. Plug the V-PS12-5V-1 power supply into the A.C. source
5. Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.
6. Turn on each of the V-R82DP-HDA screens by depressing the power switch located on the front of the unit for each screen.
Connectors
7
Tally IN
* Component Inputs comply to SMPTE274M, 294M,295M,296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
DB-15 Female
Pin1-M2Yel
Pin2-M2Red
Pin3-M2Grn
Pin4-
Pin5-Gnd
Pin6Pin7-
Pin9Pin10Pin11-M1Yel
Pin12-M2Red
Pin13-M3Grn
Pin14Pin15-Gnd
Screen aspect ratio switch 4:3 or 16:9 selector and indicators
4:3 Aspect 16:9 Aspect
Dry Erase Label
Image Adjustment Controls
Note: Tint only functions when NTSC
Video or S-Video are selected
S-Video Out
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout
S-Video In
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yin
Pin4 - Cin
Active Outputs require power to be applied
All input signals appear as output signal
Analog output signals are buffered and amplifi ed
VGA/XGA Connector
PIN# SIGNAL PIN# SIGNAL
1 RED 9 NC
2 GREEN 10 NC
3 BLUE 11 NC
4 NC 12 NC
5 GND 13 HSYNC
6 RED SHIELD 14 VSYNC
7 GREEN SHIELD 15 NC
8 BLUE SHIELD
12 VDC from
V-PS12-5V-1 power supply
Left Pin - Pos
Right Pin- Neg
DVI-I Connector
Pin#
Signal
1 T.M.D.S DATA 2- 16 HOT PLUG DETECT
2 T.M.D.S DATA 2+ 17 T.M.D.S DATA 03 T.M.D.S DATA 2/4
SHIELD
4 T.M.D.S DATA 4- 19 T.M.D.S DATA 0/5
5 T.M.D.S DATA 4+ 20 T.M.D.S DATA 56 DDC CLOCK 21 T.M.D.S DATA 5+
7 DDC DATA 22 T.M.D.S CLOCK
8 ANALOG VERT. SYNC 23 T.M.D.S CLOCK+
9 T.M.D.S DATA 1- 24 T.M.D.S CLOCK10 T.M.D.S DATA 1+
11 T.M.D.S DATA 1/3
SHIELD
12 T.M.D.S DATA 3- C2 ANALOG GREEN
13 T.M.D.S DATA 3+ C3 ANALOG BLUE
14 +5V POWER C4 ANALOG HORZ SYNC
15 GND C5 ANALOG GROUND
Pin#
Signal
18 T.M.D.S DATA 0+
SHIELD
SHIELD
C1 ANALOG RED
Marshall Electronics
V-R82DP-HDA Users Guide
6
V-R82DP-HD Users Guide
Marshall Electronics
3
Page 4
Table 1 / Computer Signals Displayed via DVI and VGA connector
Table 2 / Video Signals Displayed via DVI and YPrPb connections
(x=not available) (HDMI requires adapter to DVI)
Input Signal Type
and aspect
640 x 480 60Hz YYYY
640 x 480 75Hz YYYY
640 x 480 85Hz YYYY
800 x 600 60Hz YYYY
800 x 600 75Hz YYYY
800 x 600 85Hz YYYY
1024 x 768 60Hz Y Y Y Y
1024 x 768 75Hz YYYY
1024 x 768 85Hz YYYY
DVI-D VGA
4x3 16x9 4x3 16x9
Input Signal Type
and aspect
720 x 486 60i Y Y x x
720 x 576 50i Y Y x x
1280 x 720 60P Y Y Y Y
1280 x 720 50P Y Y Y Y
1280 x 720 30P Y Y x x
1280 x720 29.97P Y Y x x
1280 x720 25P Y Y x x
1280 x 720 24P Y Y x x
1280 x 720 23.98P Y Y x x
1920 x 1080 60i Y Y Y Y
1920x1080 59.94i Y Y Y Y
1920 x 1080 50i Y Y Y Y
1920 x 1080 30P Y Y Y Y
1920x1080 29.97P Y Y Y Y
1920 x 1080 25P Y Y Y Y
1920 x 1080 24P Y Y Y Y
1920 x 1080 24Psf Y Y Y Y
Y Pr Pb DVI
4x3 16x9 4x3 16x9
4
V-R82DP-HDA Users Guide
Marshall Electronics
5
Loading...