Marshall electronic V-R63P-SDI User Manual

V-R63P-SDI Instruction Sheet

Marshall

http://www.LCDRacks.com e-mail: [e-mail]

Broadcast Multimedia Division

Side View

2.5”

Rear View

The operation of the V-R63P-SDI is fairly straightforward, however, please take note of the following:

1. The V-R63P-SDI has been designed to fit in a 3U space on your rack. It is important to use 4 screws to hold

the ears to the rack. Be certain that the ears are aligned vertically, this is important to the tilt function.

The V-R63P-SDI has a memory function that will remember the settings of each monitor including power and
channel selection even if power has been disconnected from the unit.

2. Each LCD Panel comes with a protective plastic film that must be removed by carefully lifting the film from
the corner and peeling it off. Be certain not to apply any pressure on the LCD panels, they are fragile and can
break. Scratched, cracked or broken LCD screens are not covered by our warranty.

3. The V-R63P-SDI uses 9VDC, 3.5 Amp regulated power. Be certain that these specifications are met when
using a power supply other than the one supplied to you by Marshall Electronics. The center pin on the coaxial
power connector for the V-R63P-SDI is the POSITIVE terminal and the outside ring is NEGATIVE. Any battery
operation of the V-R63P-SDI must have this polarity configuration.

4. The Video inputs on the rear of the panel are 75 Ohm self-terminated. The loop through feature uses active
components and is always active as long as power is supplied to the unit regardless of the monitor being On or
Off. The V-R63P-SDI is also equipped with a 10-bit D/A convertor that converts the SDI input from that channel.
This D/A convertor uses the SMPTE 259M standard and is reclocked.

The V-R63P-SDI is a rack mountable unit that has three independently controlled 5.8" active matrix LCD panels with
loop through capability. These 16:9 high-resolution panels have a pixel count of 1200 × 234, and are rated at a very
bright 350 candle luminance. Each panel has an SDI and a composite video input with an NTSC/PAL switch on the
back for each channel. Each of the three screens has a built-in color bar generator, controls for brightness, color, tint,
and contrast, and a selectable aspect ratio of 16:9 or 4:3. A built in 3 color tally system is also provided for each
screen. Unit comes complete with power supply, and fits into any standard EIA 19" rack, at only 3 rack spaces high.

5.8” LCD

Active Matrix

5.01” x 2.83”
each panel

0.318mm x

0.307mm

1200H x

234V

1 NTSC/PAL

1 SDI, per panel

Built into unit

19.125W x

5.14H x 2.5D

9 VDC

3.5 Amps

Display Viewing Area Dot Pitch Inputs Color Bars Dimensions

Picture

Elements

Power

Consumption

5. Tally - The tally system on the V-R63P-SDI is accessed via the DB-15 connector on the back of the unit. The

system works by closing the contacts between the ground pin and the corresponding LED pin. The system is
self powered, DO NOT GIVE POWER TO THE PINS. The pinout is as follows:

Warranty

Marshall Electronics warranties to the first consumer, that this V-R63P-SDI rackmount monitor
will, under normal use, be free from defects in workmanship and materials, when received in its
original container, for a period of one year from the purchase date.

This warranty is extended to the first consumer only and proof of purchase is necessary to honor
the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics
reserves the right, not to honor the warranty set forth above. Therefore, labor and parts may be
charged to you.

This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or
handling, improper alterations or modifications in design or construction, voids this warranty.
No sales personnel of the seller, nor any other person is authorized to make any warranties other
than those described above, or to extend the duration of any warranties on behalf of Marshall
Electronics, beyond the time period described above.

Due to constant effort to improve products and product features, specifications may change with­out notice.

MMaarrsshhaallll

Monitor 1
Monitor 2
Monitor 3

Green

Pin 1
Pin 6

Pin 11

Red
Pin 2
Pin 7

Pin 12

Yellow

Pin 3
Pin 8

Pin 13

PINS 4, 5, 9, 10, 14 and 15
ARE COMMON GROUNDS