Marshall electronic V-R1042DP-TE4U User Manual

10

Switches and Adjustments

Marshall Electronics

1910 East Maple Ave.

El Segundo, CA 90245

Tel.: [phone] • 310-333-0606

Fax: [phone]

www.LCDRacks.com

Email: [e-mail]

Power

RATIO: Each push of the button switches

between 4:3 and 16:9 modes

MARK (16:9 mode only):

Each push of the button switches

between 16:9 standard, 4:3 marker

(shaded), and 4:3 marker (cropped)

Brightness, Color,

and Contrast controls

RATIO Settings

4:3 Mode 16:9 Mode

MARK Settings (16:9 Mode Only)

Top View

V-R1042DP-TE4U

User’s Guide

Standard 4:3 Marker (Shaded) 4:3 Marker (Cropped)

11

Warranty

Marshall Electronics warranties to the first consumer, that this V-R1042DP-TE4U portable monitor will, under normal use, be free from
defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.
This warranty is extended to the first consumer only and proof of purchase is necessary to honor the warranty. If there is no proof of pur­chase provided with a warranty claim, Marshall Electronics reserves the right, not to honor the warranty set forth above. Therefore, labor and
parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications
in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period
described above.
Due to constant effort to improve products and product features, specifications may change without notice.

04/05/07

Product Overview

Features

Standard Accessories

Optional Accessories

Electrical Specifications

Mechanical Specifications

Faceplate Cleaning

Operational Setup

Input Connectors

Switches and Adjustments

Warranty

1

2

3

4

5

6

7

8

9

10

11

1

Product Overview

The V-R1042DP-TE4U is a dual 10” high resolution LCD monitor for broadcast and professional video applications. Featuring an ultra­thin 3/8” bezel, this model provides the most possible screen area in 4RU and is ideal for video wall applications. The V-R1042DP­TE4U uses our award-winning all-digital TFT-Megapixel™ LCD panel with 2.4 million pixels, along with our HyperProcess™ de-inter-

lacing algorithm producing the smoothest motion available on a TFT LCD. Video is scaled to t on the screen in the highest possible

resolution utilizing a state-of-the-art LSI with 6x6 pixel interpolation, precision gamma correction, and Match Color Conversion™ to
produce the highest quality images available.

2

Features

TFT-MegaPixel™ Display
1024x768 Dots (2.4 Million Pixels)

SD/HD SDI Input SMPTE 259M-C, 292M / ITU-R BT.601; 1080i/60,59.95,50; 1080psF/24,23.98; 1035i/60, 59.94;

Durable metal enclosure Protection for all connections and controls with strategically placed ventilation for use in harsh envi-

Protective Screen Cover Optical grade polycarbonate screen cover with Antireective/Antiglare coating

HyperProcess™ Display interlaced images without smearing or sacricing of temporal resolution with our proprietary

MatchColor Conversion™ Factory programmed to closely match typical SMPTE/CIE color metric and color temperature speci-

OSD On screen display of Format and Ratio

50,000 hour backlight life Backlights are the most common failure on a TFT/LCD monitor. This backlight system has an MTBF

Tally 2 LEDs (Green, Red) per monitor

All signals remain completely digital to provide the most exact images available.

720p/60,59.94,50,30,29.97,25

ronments

interpolation algorithms. Images are then displayed at a sample rate equal to the frame rate.

cations. This model is adjusted for D-65 color temperature and 72% SMPTE color gamut

of 5 years and uses specially designed lamps to provide brighter images.

Recommended Anti-Static Cleaners and Polishes

210 Plastic Cleaner & Polish and 210 Plus Cleaner

Sumner Laboratories

186 Lincoln Street
Boston, MA 02111
617-542-8656 / Fax: [phone]

Crystalclean

Discovery Plastics

3700 Western Way, NE
Millersburg, OR 97231
541-926-2900 / Fax: [phone]
www.discoveryplastics.com

Scotch-Brite High Performance Cloth

3M Stationery & Ofce Supplies Div.

3M Center

St. Paul, MN 55144-1000
877-362-5684
Fax: [phone]

www.mmm.com

The Simco Industrial Static Control

An Illinois Tool Works Co.
2257 North Penn Road

Hateld, PA 19440-1998

800-203-3419
215-822-2171
Fax: [phone]

www.simco.biz

20/20 Plastic-Cleaner

Craftics, Inc.

PO Box 91930
Albuquerque, NM 87199
[phone]

Plexus Plastic Cleaner

Plexus

638 Lindero Canyon Rd. #371
Agoura, CA 91301
800-405-6495
Fax: [phone]

NOVUS #1 Plastic Clean and Shine

NOVUS, Inc.

12800 Highway 13 South, Suite 500
Savage, MN 55378
800-548-6872 ext.451
Fax: [phone]

Exair Corporation

1250 Century Circle North
Cincinnati, OH 45246-3309
513-671-3322
Fax : [phone]

www.exair.com

3

Standard Accessories

Accessories Supplied with the V-R1042DP-TE4U

• User’s manual

• “Brick” type 12VDC power supply with 2-pin twist-lock connector

4

Optional Accessories

Mount for IDX Batteries V-R65-BA

Power Adapter Cable V-PAC-XLR Use with 4 Pin XLR connections

Use with V-Mount batteries

8

Operational Setup

1. Unpack the V-R1042DP-TE4U and accompanying power supply. Physically inspect for any damage that may have occurred dur­ing shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within
the continental united states call [phone].

2. The V-R1042DP-TE4U can be mounted in an standard EIA 19-inch rack. The rack ears on the V-R1042DP-TE4U can alternately
be used as a table-top stand.

3. Connect required cables for signal input and output. Please note that power must be applied to the V-R1042DP-TE4U for the
video output to be activated. All BNC connectors should be rated for 75Ω.

4. Plug the V-PS12-5V-1 power supply into an A.C. source. Attach the 2-pin twist-lock power connector to the back of the monitor.
Please note that DC power can be supplied directly to the monitor from a variety of sources, such as a battery adapter or vehicle
power. In operation, the V-R1042DP-TE4U will draw approximately 3 Amps.
Attach 2-pin twist-lock power connector from VPS12-5V-1 power supply to the back of the unit.

5. Turn on the V-R1042DP-TE4U by pressing the power switch located on the front of the unit.

9

Input Connectors

(Active output requires monitor

* Tally lamps active when connected to ground

HDSDI Inputs/Outputs

to be powered)

Switches and Adjustments -

See Section 10

12VDC Power Input

Tally Pinout (HD-15)

Pin No. Signal

1 Green (Monitor 1)

2 Red (Monitor 1)

3 N/C

4 Ground

5 Ground

6 N/C

7 N/C

8 N/C

9 N/C

10 N/C

11 Green (Monitor 2)

12 Red (Monitor (2)

13 N/C

14 Ground

15 Ground

2

V-R1042DP-TE4U User’s Guide

Marshall Electronics

5

Optional Accessories (continued)

Battery Adapter

Sequential 2 channel charger

Sequential 4 channel charger

Simultaneous 4 channel charger

55 W Lithium Battery IDX-E7S V-Mount battery pack with 3 LED power Indicator

V-DV-PWR1

IDX-VL-2Plus

IDX-VL-4

IDX-VL-4S Charges 4 ENDURA E series batteries in 2.5 hours or less

Uses 2 Sony DVCam/HDV FP-Type batteries.
When used with monitor power supply, can charge batteries
plus operate monitor

2-channel sequential charger with a built-in 60W power sup­ply. Charges 2 ENDURA E series batteries in fewer than 5
hours. One 10’ XLR cable included. Weighs only 2 lbs

Economically charges 4 ENDURA E series batteries in
under 6 hours using Full Power Charge (FPC) method

55 W Lithium Battery
with Power Link

82 W Lithium Battery IDX-E10S V-Mount battery pack with 3 LED power Indicator

82 W Lithium Battery
with Power Link

Analog to Digital Converter BC-0909-AD Converts composite, Y/C, or YPbPr signals to HDSDI

Cleaning Wipes V-HWP-K

IDX-E7

IDX-E10

V-Mount Battery Pack with PowerLink includes accurate
Power Status Display and supports Digi-View

V-Mount Battery Pack with PowerLink includes accurate
Power Status Display and supports Digi-View

Package of 10 non-toxic, antistatic, alcohol and ammonia
free cleaning wipes.

Marshall Electronics

3

Electrical Specications

5

Display (Viewing Area) 10.4 Inch diagonal (211.2mm W x 158.4mm H)
Screen Aspect Native 4:3, Switchable to 16:9
Resolution (RGB Dots) 1024HxRGx768V (2.4 Million Pixels)
Viewing Angles 170°H x 170°V
Contrast Ratio 400:1
Dot Pitch 0.206mm square pixel
Pixel Response 13ms rise /12ms fall
Brightness 400 cd/m²
Backlight Field Replaceable CCFL (50,000 hour half life)
Screen Treatments Anti Reflection, Anti Glare, Hard Coat
Protective Screen 0.118” (3mm) thick Optical Grade Polycarbonate with Anti-Glare and Anti-Abrasion

coatings. (600 Cheesecloth mil-M-13508C)

Estimated MTBF 5 years of 24/7 operation
Inputs 1 SDI/HDSDI input per screen; SMPTE 259M-C, 292M / ITU-R BT.601; female BNC;

1080i/60,59.95,50; 1080psF/24,23.98; 1035i/60,59.94; 720p/60,59.94,50,30,29.97,25

Active Outputs 1 SDI/HDSDI output per screen; SMPTE 259M-C, 292M / ITU-R BT.601; female BNC
Tally 2 LEDs (Green, Red) per monitor; female HD-15 connector
Color temperature D65 (6500° Kelvin)
Color Gamut SMPTE-C/EBU
Luma Linearity Typical +/- 3% with 5 ire increments (0 to 10 ire)
Power Required 10.4 to 16.8 VDC
Power Consumption 36 watt nominal for V-R1042DP-TE
Operating Temperature 32°F to 120°F (0°C to 50°C)
Storage Temperature -4°F to 120°F (-20°C to 50°C)
Compliance
RoHS WEEE/Environmental Do not dispose. Return to Manufacturer or Authorized Recycle Facility
V-PS12-5V-1 Power Supply 14-10 VDC (Universal Voltage 5.0Amps max - UL Class 2 supply included)

₠, FCC-Class A, ANSI-63.4 (Certificates on file)

Mechanical Specication

6

V-R1042DP-TE4U V-PS12-5V-1 Power Supply

Dimensions (W x H x D)

(Main body only)

Approx. Weight 5.0 lbs 0.65 lbs

Faceplate Cleaning

7

Faceplate Cleaning

When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro ber

cloth. Do not use paper towels. Paper towel bers are coarse and may scratch the surface of the Polycarbonate faceplate.
Paper towels may also leave streaks on the surface. Antistatic and ngerprint resistant cleaning agents are recommended.

Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pres­sure. Rinse with clean water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade
of hexane, aliphatic naphtha, or kerosene. These solvents may be obtained at a paint or hardware store and should be used in ac­cordance with manufacturer’s recommendations.

DO NOT USE: window cleaning sprays, kitchen scouring compounds or solvents such as acetone, gasoline, benzene,
alcohol, carbon tetrachloride, or lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing
small surface cracks called “crazing.”

Faceplate Dusting

Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the
surface. Neutralizing static electricity effects by using recommended cleaning and polishing practice.

Faceplate Polishing

Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft

clean cloth and polish lightly with cotton annel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract

dust particles.

Marking on the Faceplate

Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent.

18.9” x 7.0” x 1.6” 4.13” x 2.50” x 1.25”

4

V-R1042DP-TE4U User’s Guide