Marshall electronic V-R102DP-SD User Manual

V-R102DP-SD

Users Guide

SDI: 525i/60hz 4x3

OSD

Use SELECT to enable the On Screen Display

for input and function status

Marshall Electronics

1910 East Maple Ave.

El Segundo, CA 90245

Tel.: [phone] • 310-333-0606

Fax: [phone]

www.LCDRacks.com

Email: [e-mail]

Blue Only

SELECT to adjust SMPTE or split fi eld color bars.

1. Allow monitor to warm up for 5-10 minutes minimum.

2. Display SMPTE color bars on monitor. Turn on off Color with control.

3. Find the PLUGE (superblack, black, and gray bars) at the lower right
of the pattern.
Adjust BRIGHTNESS until there is no difference visible between the super­black and black bars, but is still visible.

4. Adjust CONTRAST control to achieve a balanced gray scale across
top bars.

5. Turn up CHROMA (color level) control until the two outermost bars
(white and blue appear to match in brightness.

6. NTSC Only -Adjust COLOR PHASE (tint or hue) control until the third
bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.

V-R102DP-SD

Users Guide

10

Warranty

Marshall Electronics warranties to the first consumer, that this V-R102DP-SD Dual 10.4-inch LCD rack mounted monitor set will, under
normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date.
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof
of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore,
labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifica­tions in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any war­ranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time
period described above.
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of
the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to
effective use of the monitor by our technicians.
Due to constant effort to improve products and product features, specifications may change without notice.

8

Product Overview

Features

Video - Screen Formats and Frame Rates

Electrical Specifications

Mechanical Specifications

Operational Setup

Connectors

Switch Settings, Adjustments and Indicators

Menu Functions

Warranty

1

2

3

4

5

6

7

8

9

10

1

Product Overview

The V-R102DP-SD features our Completely Digital TFT-Megapixel™ high defi nition TFT/LCD system with 1.44 million pixels. Analog
signals are digitized using an advanced 10 bit process with 4x over sampling and adaptive 5 line comb fi lter plus exacting color space
conversion. Video is scaled to fi t on screen in the highest resolution using a state of the art LSI that incorporates 6x6 pixel adaptive
motion interpolation with precision Gamma correction. Additional features include Pixel-to-Pixel™ native resolution scaling, setup
memory, Underscan, H/V Delay, adjustable color temperature, and Blue Gun.

2

Features

• TFT-MegaPixel™ totally digital end to end signal processing

• Multiple format acceptance for virtually any analog or digital video signal

• Display PC Signals to XGA 1024x768

• ColorMatch Conversion™ with SMPTE/EBU color space emulation of CRT

• Color temperature preset for D65

• HyperProcess™ motion interpolation of interlace images

• On screen display of input status, formats, and menu functions

• Pixel to Pixel™ native resolution display

• Ready to mount – all brackets are factory installed

• Lightweight – 75% lighter than CRT models

• Settings memory restores active state with power off/on cycle

• Underscan plus H & V delay

• Blue only (Blue Gun) for adjustment to SMPTE color bars

• Includes V-PS12-5V-1 Universal power supply (U.L. class 2)

• Three LEDs (Red, Green, Amber) produce 7 different tally indications on each screen

• Dry erase label for each screen

3

Video - Screen Formats and Frame Rates

• 525 –60i / 625 - 50i (Interlaced NTSC/PAL)

• 480P (Progressive)

• 576P (Progressive)

• 720P-50P, 59.94P, 60P, 25P, 29.97P, 30P, 50P, 59.94P, 60P (Progressive)

• 1035i - 59.94i, 60i (Interlaced)

• 1080i x 1920 – 50i, 59.94i, 60i, 23.973P, 24P, 25P, 29.97P, 30P, 24psf, 23.97psf

4

Electrical Specifications

All signal types and frame rates are automatically detected

9

Menu Functions

1. Power On/Off Button

Illuminates Red when system power is present. Illuminates Green when monitor is ON.

2. Source Selection Buttons

Video - Composite NTSC or PAL. Composite video must comply to SMPTE-RS170M.

Images without color burst (Subcarrier) component may not display.

S-Video - Y/C (Luminance + Chrominance) NTSC or PAL.
YPrPb - Analog Component color difference signals for Standard Defi nition (YCrCb) or High Defi nition (YPrPb).
VGA - Analog PC.
DVI - Digital Computer or Video Signals. Includes HDCP for use with HDMI originated signals.
SDI - Digital Input for Standard Defi nition (SDI-270Mbs).

3. Pixel to Pixel Function

As the native LCD displays of the V-R102DP-SD are 800 pixels wide by 600 dots (RGB pixels) high, it is necessary to change the size of
the image to fi ll the whole screen. Pixel to Pixel mode bypasses the enlargement/shrink of this scaling function and displays the native
incoming format.

For 525-NTSC/480P based images, pixel to pixel will appear as a 480x640 (4:3 aspect) or 480x720 (16:9 aspect).
For 625-PAL/576P based images, pixel to pixel will appear as a 576x640(4:3 aspect) or 576x720 (16:9 aspect).
For 1080 line HD based images, pixel to pixel will appear as cropped 800x600 (4:3 aspect) starting from the center of the

image. 240 lines top, 240 lines bottom, 560 pixels left and 560 pixels right will be cropped.
For 720 line HD based images, pixel to pixel will appear as cropped 800x600 (4:3 aspect) with 60 lines from the top and 60 lines from
the bottom cropped. Horizontally, 240 pixels will be cropped from each edge.

3. Menu Enable and navigation

Access menu functions by selecting the MENU button. Use UP / DOWN to navigate and
SELECT to enable or disable the function

Note: Source selection is disabled when in menu mode.

Color Temperature
D-65 (6500K) - Standard setting recommended by SMPTE and EBU.

Simulates normal daylight conditions.

USER - When activated manual adjustment is performed by selecting
Adj. Color Gain or Adj. Color Bias

Screen Aspect 4:3/16:9 switchable
Display (Viewing Area) 8.4 Inch diagonal (170.4mm w x 127.8mm h)
Viewing Angles 130° H x 120° V
Resolution (RGB Dots) 800H×RGBx600V (1.44 million pixels)
Color Depth 262,000 Colors (6-Bit)
Dot Pitch .213mm square pixel
Contrast Ratio 350:1
Pixel Response 10ms rise/25ms fall
Brightness (in cd/m²) 500 cd/m²
Backlight Field Replaceable CCFL (50,000 hour half life)
LCD Screen Treatments Anti Reflection, Anti Glare, Hardcoat
Estimated MTBF 5 years of 24/7/365 operation
System NTSC/PAL with auto recognition
Inputs SDI (SMPTE259M) (ITR-U601) per screen (BNC)

YPrPb Component (3 BNC)
Composite Video PAL/NTSC auto detect (BNC)
S-Video (Y/C) (4 Pin Mini Din female)
XGA 15Pin HD-15 Female
DVI 27 (Pin DVI-I Female)

Active Outputs SDI (SMPTE259M) (ITU-RBT601) per screen (BNC)

Color temperature D65 and User Adjustment
Color Gamut SMPTE-C/EBU 80% CIE
Luma Linearity Typical +/- 3% with 5 IRE increments (0 to 10 IRE)
Power Required 10.8 to 13.2 VDC
Power Consumption Approx. 40 watt nominal

Operating temperature
Storage temperature
Compliance
RoHS WEE / Environmental

2

Tally (HD-15 Female)

YPrPb Component (3 BNC)
Composite Video PAL/NTSC auto detect

32° F to 120° F (0° C to 50° C)

-4 F to 120° F (-20° C to 50° C)
₠, FCC-Class A, ANSI-63.4 (Certificates on file)

Do not dispose. Return to Manufacturer or Authorized Recycle Facility

V-R102DP-SD Users Guide

When in adjust mode use UP/DOWN to change values. Use SELECT to cycle RED, GREEN,
and BLUE mode. Exit to the main menu by pressing MENU.

Left Line= Increase of Gain

Center Line = D65 (Default)

Right Line = Decrease of Gain

Level Set-up
SELECT between 7.5 IRE for NTSC signals and 0 IRE for NTSC Japan and PAL signals.

7.5 mode will enable a digital black offset of the onscreen images for improved Blacks.

Color Bar

Use to SELECT internal test signal of full fi eld color bars that is available for confi rmation
of LCD operation. This function will disable input selection until cycled off.

H/V Delay

Use to SELECT display of horizontal and vertical blanking areas.
Not available for all signal types.

Under Scan

Use SELECT to reduce the display area with expansion beyond active video. Note that the
V-R102DP-SD is factory adjusted to display 100% of active video in standard display mode.
This function is normally used with analog Standard defi nition signals. SDI signals will dis-
play all video with ancillary data appearing to the right of the image.

Right Line= Increase of Bias

Center Line = D65 (Default)

Left Line = Decrease of Bias

Marshall Electronics

7