Marshall electronic V-R102DP-HD User Manual

V-R102DP-HD

Users Guide

SDI: 525i/60hz 4x3

OSD

Use SELECT to enable the On Screen Display

for input and function status

Marshall Electronics

1910 East Maple Ave.

El Segundo, CA 90245

Tel.: [phone] • 310-333-0606

Fax: [phone]

www.LCDRacks.com

Email: [e-mail]

Blue Only

SELECT to adjust SMPTE or split fi eld color bars.

1. Allow monitor to warm up for 5-10 minutes minimum.

2. Display SMPTE color bars on monitor. Turn on off Color with control.

3. Find the PLUGE (superblack, black, and gray bars) at the lower right
of the pattern.
Adjust BRIGHTNESS until there is no difference visible between the super­black and black bars, but is still visible.

4. Adjust CONTRAST control to achieve a balanced gray scale across
top bars.

5. Turn up CHROMA (color level) control until the two outermost bars
(white and blue appear to match in brightness.

6. NTSC Only -Adjust COLOR PHASE (tint or hue) control until the third
bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.

V-R102DP-HD

Users Guide

10

Warranty

Marshall Electronics warranties to the first consumer, that this V-R102DP-HD Dual 10.4-inch LCD rack mounted monitor set will, under
normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date.
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof
of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore,
labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifica­tions in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any war­ranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time
period described above.
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of
the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to
effective use of the monitor by our technicians.
Due to constant effort to improve products and product features, specifications may change without notice.

8

Product Overview

Features

Video - Screen Formats and Frame Rates

Electrical Specifications

Mechanical Specifications

Operational Setup

Connectors

Switch Settings, Adjustments and Indicators

Menu Functions

Warranty

1

2

3

4

5

6

7

8

9

10

5

Mechanical Specifications

8

Switch Settings, Adjustments and Indicators

Tally Lamps

V-R102P-HD

Dimensions 19.12” w x 8.67” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)
V-R82DP-HD Weight 5.5 lbs (2.4 kg)
V-PS12-5V-1 Power Supply Weight 1 lbs (0.45kg)

6

Operational Setup

1. Unpack the V-R102DP-HD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have
occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.
If you are not located within the continental United States call [phone].

2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when
installed to prevent possible damage to the V-R102DP-HD internal components.

3. Connect required cables for signal input and output. Please note that power must be applied to the V-R102DP-HD for all outputs
to be activated. All BNC connectors should be rated for 75Ω.

4. Plug the V-PS12-5V-1 power supply into the A.C. source

5. Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.

6. Turn on each of the V-R102DP-HD screens by depressing the power switch located on the front of the unit for each screen.

Connectors

7

* HDSDI/SDI Inputs comply to SMPTE-259M, 292M, SDI-270Mbs , HDSDI-1.485 Gb/s
* Component Inputs comply to SMPTE274M, 294M,295M,296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground

Pin1-M2Yel
Pin2-M2Red
Pin3-M2Grn
Pin4-
Pin5-Gnd
Pin6­Pin7-

Tally IN

DB-15 Female

Pin9­Pin10­Pin11-M1Yel
Pin12-M2Red
Pin13-M3Grn
Pin14­Pin15-Gnd

Screen aspect ratio switch 4:3 or 16:9 selector and indicators

4:3 Aspect 16:9 Aspect

Dry Erase

Image Adjustment Controls

Note: Tint only functions when NTSC

Video or S-Video are selected

S-Video Out

4 Pin Din (Female)

Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout

S-Video In

4 Pin Din (Female)

Pin1 - GND
Pin2 - GND

Pin3 - Yin
Pin4 - Cin

Active Outputs require power to be applied

All input signals appear as output signal

Analog output signals are buffered and amplifi ed

VGA/XGA Connector

PIN# SIGNAL PIN# SIGNAL

1 RED 9 NC
2 GREEN 10 NC
3 BLUE 11 NC
4 NC 12 NC
5 GND 13 HSYNC
6 RED SHIELD 14 VSYNC
7 GREEN SHIELD 15 NC
8 BLUE SHIELD

12 VDC from

V-PS12-5V-1 power supply

Left Pin - Pos

Right Pin- Neg

DVI-I Connector

Pin#

Signal

1 T.M.D.S DATA 2- 16 HOT PLUG DETECT
2 T.M.D.S DATA 2+ 17 T.M.D.S DATA 0­3 T.M.D.S DATA 2/4

SHIELD

4 T.M.D.S DATA 4- 19 T.M.D.S DATA 0/5

5 T.M.D.S DATA 4+ 20 T.M.D.S DATA 5­6 DDC CLOCK 21 T.M.D.S DATA 5+
7 DDC DATA 22 T.M.D.S CLOCK

8 ANALOG VERT. SYNC 23 T.M.D.S CLOCK+
9 T.M.D.S DATA 1- 24 T.M.D.S CLOCK­10 T.M.D.S DATA 1+
11 T.M.D.S DATA 1/3

SHIELD
12 T.M.D.S DATA 3- C2 ANALOG GREEN
13 T.M.D.S DATA 3+ C3 ANALOG BLUE
14 +5V POWER C4 ANALOG HORZ SYNC
15 GND C5 ANALOG GROUND

Pin#

Signal

18 T.M.D.S DATA 0+

SHIELD

SHIELD

C1 ANALOG RED

Marshall Electronics

V-R102DP-HD Users Guide

6

V-R82DP-HD Users Guide

Marshall Electronics

3