Marshall electronic V-LCD15SB-AFHD-DT User Manual

Maintenance

Marshall Electronics

, Inc.

■

Screen Cleaning

Specifications (continued)

Marshall Electronics

V-LCD15SB-AFHD-DT

SD/HD SunBrite LCD Monitor

Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro­fiber cloth can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels.
Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the
surface. Antistatic and fingerprint resistant cleaning agents are recommended. Do not apply excessive pressure to the
screen to avoid damaging the LCD.

■

Faceplate Dusting

Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface,
attracting dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.

Warranty

Marshall Electronics warranties to the first consumer that this V-LCD15SB-AFHD-DT LCD monitor will, under normal use,
be free from defects in workmanship and materials, when received in its original container, for a period of one year from
the purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the
warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to
honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not
apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or modifications in design or
construction void this warranty. It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the
periphery of the display active viewing area. Marshall Electronics reserves the option to refuse service for display pixel
failure if deemed unobtrusive to effective use of the monitor by our technicians. No sales personnel of the seller or any
other person is authorized to make any warranties other than those described above, or to extend the duration of any
warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve
products and product features, specifications may change without notice.

Operating Instructions

1910 East MapleAve.

El Segundo, CA 90245

Tel: [phone] • Fax: [phone]

www.LCDRacks.com • [e-mail]

Updated: 05/18/07

16

Contents

Specifications

Product Overview.....................................................................................................................................................3

Features ....................................................................................................................................................................3

Installation and Initial Setup ...................................................................................................................................4

Unpacking..............................................................................................................................................................4

Installation..............................................................................................................................................................4

Connections and Power-On...................................................................................................................................4

Front Panel Features ...............................................................................................................................................5

Power Button ........................................................................................................................................................5

Input Select Buttons...............................................................................................................................................5

On-Screen Menu Navigation Buttons ....................................................................................................................5

User-Definable Function Buttons...........................................................................................................................5

Image Adjustment Knobs.......................................................................................................................................5

Tally Lights.............................................................................................................................................................5

Rear Panel Features.................................................................................................................................................6

Power Input............................................................................................................................................................6

Signal Input/Output................................................................................................................................................6

Tally Interface ........................................................................................................................................................6

Mounting Holes......................................................................................................................................................6

Compatible Input Formats.......................................................................................................................................7

On-Screen Menu.......................................................................................................................................................8

STRUCTURE OVERVIEW ....................................................................................................................................8

MAIN MENU AND NAVIGATION ..........................................................................................................................8

MARKER SETUP SUBMENU ...............................................................................................................................9

16:9 Markers......................................................................................................................................................9

4:3 Markers......................................................................................................................................................10

Marker Background.........................................................................................................................................10

Center Marker..................................................................................................................................................10

VIDEO CONFIGURATION SUBMENU ...............................................................................................................11

Color Temperature Presets .............................................................................................................................11

Adjusting Color Bias........................................................................................................................................11

Adjusting Color Gain........................................................................................................................................11

Monochrome Mode..........................................................................................................................................12

Blue Only Mode...............................................................................................................................................12

Pixel-to-Pixel™ Mode......................................................................................................................................12

Aspect Ratio Setting........................................................................................................................................13

Scanning Modes..............................................................................................................................................13

Delay Modes....................................................................................................................................................13

SYSTEM CONFIGURATION SUBMENU............................................................................................................14

Internal SMPTE Color Bars.............................................................................................................................14

User-Definable Function Buttons ....................................................................................................................14

Status Display..................................................................................................................................................14

Saving and Loading User Configuration Presets ............................................................................................14

■

PANEL

Screen Size 15.0” Diagonal
Display Area (h x v) 304.128 x 228.096 mm
Aspect Ratio 4:3 Native (4:3/16:9 Modes)
Pixels 1024 x RGB x 768
Color Depth 16,777,216 Colors
Viewing Angle (h x v) 160° x 140°
Brightness 600 cd/m
Contrast Ratio 600:1
Dot Pitch (h x v) 0.099 x 0.297 mm
Pixel Pitch (h x v) 0.297 x 0.297 mm
Pixel Response 18 ms (rise + fall)

■

VIDEO INPUT/OUTPUT

Video Input / Output

Supports SMPTE 170M, NTSC/PAL
Color burst/sub-carrier required

S-Video (Y/C) Input / Output

Supports SMPTE 170M, NTSC/PAL

YPBPRInput / Output

Supports SMPTE 260M, 274M, 296M

HD-SDI Input / Output

Supports ITU-R BT.656, SMPTE 259M. 292M

VGA Input

Supports RGBHV, RsGsBs, RGsB, RGB CS,

DVI Input

Supports Digital Signals Only (DVI-D)
HDCP Supported

■

CONNECTORS

Video Input

Video 1 x BNC Female (75 Ω)
S-Video (Y/C) 1 x 4-Pin Mini-DIN
YPBP

R

HD-SDI 1 x BNC Female (75 Ω)
VGA 1 x HD-15 Female
DVI 1 x DVI-I 29-Pin Female

Video Output (Active Loop-Through)

Video 1 x BNC Female (75 Ω)
S-Video (Y/C) 1 x 4-Pin Mini-DIN
YPBP

R

SDI 1 x BNC Female (75 Ω)

3 x BNC Female (75 Ω)

3 x BNC Female (75 Ω)

2

■

TALLY

3 LEDs (Green, Red, Yellow). Activation requires contact
closure of pin to ground on the HD-15 connector:

Pin No. Signal

1 Green
2 Red
3 Yellow
4 Ground
5 Ground
6 N/C
7 N/C
8 N/C
9 N/C
10 N/C
11 N/C
12 N/C
13 N/C
14 Ground
15 Ground

■

ELECTRICAL

Power Consumption 3A @ 12VDC (36 W)
Voltage Requirement 12-14 VDC

V-PS12-5V-1 Power Supply:

Input 100V-240V, 50/60Hz
Output 12-14V, 5A

■

MECHANICAL

Dimensions (w x h x d): 15.25” x 10.45” x 1.77”
Height with Stand: 11.01”
Rack Height: 6 RU
Additional Mounting: VESA 75 mm

Weight (Monitor Only): 8.1 lbs
Operating Temperature 32°F to 120°F (0°C to 50°C)
Storage Temperature -4°F to120°F (-20°C to 50°C)

Compliance ₠, FCC-Class A, ANSI-63.4

(Certificates on file)

RoHs Do not dispose. Return to

Manufacturer or Authorized
Recycle Facility.

Specifications.........................................................................................................................................................15

Maintenance............................................................................................................................................................16

Warranty..................................................................................................................................................................16

Power Input

2-Pin Conxall Twist-Lock Female

Tally Interface

HD-15 Female

2

15

On-Screen Menu (continued)

SYSTEM CONFIGURATION SUBMENU

Video Configuration Submenu

■

Internal SMPTE Color Bars

Use to display internally generated SMPTE split-field color bars.

■

User-Definable Function Buttons

Use the FUNCTION 1 and FUNCTION 2 menu items to define each function button on the front panel of the monitor.
The following options are available for each button:

• DELAY Enable and rotate amongst delay modes.

• RATIO Toggle between 4:3 and 16:9 aspect ratios.

• BACK Rotate amongst marker backgrounds.

• CENTER Enable/disable center marker.

• MARKER Enable and rotate amongst marker settings (choices depend on aspect ratio setting).

• MONO Enable/disable monochrome mode.

• CTEMP Rotate amongst color temperature settings.

• PTP Enable/disable Pixel-to-Pixel™ mode.

FUNCTION 1 is set to RATIO by default.
FUNCTION 2 is set to PTP by default.

■

Status Display

Use to enable on-screen display of input/format status in the upper-left corner of the screen.

■

Saving and Loading User Configuration Presets

Use the SAVE CONFIG and LOAD CONFIG menus to save current settings to one of 6 presets, or load a preset. All
monitor settings on the monitor are saved, including the image adjustment knob settings.

• Use the LOAD CONFIG menu to load one of presets USR1 – USR6. Factory default settings can also be loaded
by selecting MFG. (Factory defaults cannot be overwritten.)

• Use the SAVE CONFIG menu to save the current settings to a preset from USR1- USR6.

Product Overview

The V-LCD15SB-AFHD-DT is a 15” SD/HD video LCD with Marshall Electronics’ proprietary SunBrite LCD panel,
designed specifically for outdoor applications or high levels of ambient light. The V-LCD15SB-AFHD-DT features our
completely digital TFT-MegaPixel™ active matrix LCD system. Weighing only 8.1 lbs and only 1.77” deep, this monitor is
an ideal lightweight replacement for CRTs used in all broadcast and professional video applications. Emulation of
SMPTE-C/EBU color and adjustable color temperature enable the most precise color representation possible. Our
proprietary digital signal processing features 10-bit A/D conversion of all analog signals, with 4X over-sampling and 5-line
super-adaptive 2D comb filtering of composite signals. De-interlacing is performed using our HyperProcess™ algorithm
with motion adaptive interpolation. The V-LCD15SB-AFHD-DT features multi-format compatibility, accommodating
virtually all video formats including NTSC/PAL, 480i/p, 720p, and 1080i/p formats. VGA and DVI inputs accept VESA
standards allowing the display to be used as a computer monitor. Advanced features include aspect ratio settings, a
variety of screen markers, underscan mode, blue-only mode, monochrome mode, H/V delay, and Pixel-to-Pixel™ mode.

Features

■

High-Resolution 15” SunBrite Panel

The V-LCD15SB-AFHD-DT features Marshall Electronics’ new SunBrite LCD panel, dramatically boosting the
efficiency of the backlight’s light utilization and minimizing the surface reflection of ambient light. The transmissive LCD
produces high-contrast images, even in challenging outdoor lighting conditions. This technology features a much wider
color reproduction range than typical transflective/reflective LCDs with increased backlight performance. The LCD
panel features a brightness of 600 cd/m2, 600:1 contrast ratio, and 160° horizontal and 140° vertical viewing angles.

■

Multi-Format Compatibility

With a variety of analog and digital inputs, the V-LCD15SB-AFHD-DT accommodates virtually all video formats. Input
types include Composite Video, S-Video, YPbPr, SDI, VGA, and DVI with HDCP. Accepted formats include
NTSC/PAL, 480i/p, 576i/p, 720p, 1035i, and 1080i/p standards, as well as VESA PC formats through SXGA (1280 x

1024).

■

End-to-End Digital Signal Processing

Analog signals are digitized using an advanced 10-bit process with 4x over-sampling, 5-line super-adaptive 2D comb
filtering, and exacting color space conversion. Video is scaled to fit on the screen in the highest possible resolution
using a state-of-the-art LSI that incorporates precision gamma correction and our HyperProcess™ motion adaptive
interpolation for interlaced images.

■

ColorMatch™ Conversion with Color Temperature Adjustment

Emulation of SMPTE-C/EBU color space allows the V-LCD15SB-AFHD-DT to replace any broadcast CRT monitor.
Settings include D55, D65 and D95. Bias and Gain adjustment for each color enables precise color matching and white
balance.

■

Advanced Features

Aspect ratio settings, underscan mode, blue-only mode, monochrome mode, and H/V delay are a few of the advanced
features making the V-LCD15SB-AFHD-DT at home in any broadcast environment. Pixel-to-Pixel™ mode also allows
native display of any incoming image format.

■

Flexible Screen Markers

A variety of screen markers in both 4:3 and 16:9 modes allow accurate monitoring of the different aspect ratios used in
broadcast environments.

14

■

User-Definable Function Buttons

Two user-definable function buttons on the front-panel allow quick access to numerous settings and features including
aspect ratio, screen markers, monochrome mode, color temperature, delay mode, and more.

3

Installation and Initial Setup

■

Unpacking

Carefully unpack the V-LCD15SB-AFHD-DT monitor and verify that the following items are included:

• V-LCD15SB-AFHD-DT Monitor with Attached Desktop Stand

• V-PS12-5V-1 Power Supply with Conxall 2-Pin Twist-Lock Connector

• Operating Instructions

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU (continued)

■

Aspect Ratio Settings

Use to switch between 4:3 and 16:9 aspect ratios.

As the V-LCD15SB-AFHD-DT monitor has a native resolution of 1024 x 768 RGB pixels, incoming images are
automatically scaled to fit the screen:

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,
immediately contact Marshall Electronics at [phone]. If you are not located within the continental United States,
call [phone].

■

Installation

The V-LCD15SB-AFHD-DT monitor is shipped with pre-installed desktop stand, allowing the monitor to be flexibly used
in the field. The monitor can also be installed in an EIA standard 19-inch rack, occupying 6RU (contact Marshall
Electronics). When installed in a rack, the unit can be rotated 360° to achieve the desired viewing angle.

A VESA standard 75mm hole pattern also allows custom mounting installations on stands or articulating arms.

■

Connections and Power-On

Plug the V-PS12-5V-1 power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist-lock
connector to the back of the monitor. Please note that 12-17VDC can be also supplied directly to the monitor from a
variety of sources. The monitor will draw approximately 3 Amps at 12 Volts in operation.

Connect the required cables for video signal input and output. (Power must be applied to the V-LCD15SB-AFHD-DT
for the active loop-though outputs to be activated.) All BNC connectors are rated at 75Ω.

Turn on the unit by pressing the power button located on the front panel. Select a video input by pressing the
corresponding input select button.

• In 4:3 mode, images are scaled up or down to fill the entire 4:3 screen (1024 x 768).

• In 16:9 mode, images are scaled to fill the maximum 16:9 portion of the screen (1024 x 576), with black bars filling
the remainder of the screen.

4:3 Mode

Note: The aspect ratio setting is ignored when Pixel-to-Pixel™ mode is enabled.

■

Scanning Modes

Use this setting to switch between normal and underscan modes:

• In normal scan mode, the active portion of the video signal is displayed on the screen, with 0% overscan.

• In underscan mode, area around the active video area is displayed on the screen, resulting in blanking intervals
being shown around the perimeter of the active image. Use this mode to clearly view the edges of the active video
area.

16:9 Mode

■

Delay Modes

Use this setting to enable one of three delay modes (H/V, H, V):

• In H/V delay mode, both horizontal sync and vertical sync are delayed, resulting in both horizontal and vertical
blanking periods being shown on the screen.

• In V delay mode, vertical sync is delayed so that the vertical blanking period is displayed on screen.

• In H delay mode, horizontal sync is delayed so that the horizontal blanking period is displayed on the screen.

Note: Delay modes are only available in normal scan mode.

4

13

On-Screen Menu (continued)

Front Panel Features

VIDEO CONFIGURATION SUBMENU (continued)

■

Monochrome Mode

Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale
picture.

■

Blue-Only Mode

Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching
off the red and green components. Use this mode when calibrating the monitor to SMPTE color bars with the following
procedure:

1. Allow the monitor to warm up for at least 5-10 minutes.

2. Display SMPTE split-field color bars on the monitor using the internal generator or an external source.

3. Enable Monochrome mode.

4. Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of the screen. Adjust the Brightness knob until there is
no visible difference between the super black and black bars, but the gray bar is still visible.

5. Adjust the Contrast knob until an even grayscale appears along the top bars.

6. Disable Monochrome mode.

7. Enable Blue-Only mode and adjust the Color knob so that the outermost bars (white and blue) appear to match in brightness.

1

Power Button

Turn the monitor on by pressing the power button.
In the OFF state, the LED will shine brightly. The
LED will dim when the monitor is turned on.

Input Select Buttons

2

Use the input select buttons to select the input to be
displayed:

• Video

• S-Video

• YPbPr (SD/HD)

• VGA

• DVI

• SDI

Each input automatically detects the applicable
formats (See Compatible Input Formats – Page 7).

On-Screen Menu Navigation Buttons

3

Use the Menu, ↑, ↓, and Select buttons to display
and navigate the on-screen menu (See Main Menu

and Navigation – Page 8).

1

2

3

4

8. Composite/S-Video NTSC only: Adjust the Tint knob until the third bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.

9. Disable Blue-Only mode.

■

Pixel-to-Pixel™ Mode

Use this setting to enable Pixel-to-Pixel™ mode.
This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and

aspect ratio, with a one-to-one mapping:

• For incoming formats smaller than the native resolution of the LCD panel (1024 x 768), the image will be
displayed in the center of the screen using only the necessary LCD pixels. For example, NTSC or PAL images will
occupy exactly 720 x 486 or 720 x 576 pixels respectively. The surrounding pixels will be black.

• For incoming formats exceeding 1024 x 768 pixels, only the center 1024 x 768 of the incoming image will
displayed occupying the whole screen, with the remainder of the picture cropped. For example, 1080 and 720
formats will both be cropped to 1024 x 768 and displayed full-screen.

Note: Pixel-to-Pixel™ mode will utilize the entire screen (1024 x 768) regardless of the aspect ratio setting. Pixel-to­Pixel™ mode is not available when using the VGA or DVI inputs.

4

User-Definable Function Buttons

Two user-definable function buttons can be used for
direct access to various settings. Functions are
assigned using the on-screen menu (See User-

Definable Function Buttons – Page 14).

Image Adjustment Knobs

5

Use the image adjustment knobs to adjust the
following settings. Pressing each knob will display
the current status of the corresponding control:

• Brightness (0-64)

• Color (0-64)

• Tint (0-64) [NTSC Only]

• Contrast (0-64)

Tally Lights

6

Three tally LEDs (green, red, and yellow) are
provided as general purpose indicators. Each LED
can be individually controlled, providing multiple
indications. Tally LEDs are controlled via the HD-15
connector on the rear panel (See Tally Interface –

Page 6).

5

Right Front Panel

6

Top Front Panel

12

5

Rear Panel Features

1

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU

4

3

2

Power Input

1

Connect the 12VDC input to the Conxall 2-pin twist-lock
power input connector. Power can be supplied from the
included power supply, or from a variety of DC sources
supplying at least 3 Amps at 12 Volts.

IMPORTANT: If using a power source other than the
included power supply, be sure that the polarity of the
DC input is correct:

Pin 1: +12VDC
Pin 2: GND

Signal Input/Output

2

Connections:

• Composite Video Input/Output (BNC)

• S-Video Input/Output (4-Pin Mini-DIN)

• YPBPRInput/Output (BNC x 3)

• SDI Input/Output (BNC)

• VGA (HD-15)

• DVI (29-Pin connector, DVI-D signals only)

All outputs are active and require the monitor to be
powered.

Rear Panel

3

Tally Interface

Each tally light is activated via the HD-15 connector by
connecting the corresponding pin to ground. A variety of
external devices can be used to perform the contact
closure. No additional power should be supplied to the
HD-15 port.

Tally Interface: HD-15 Pinout

Pin No. Signal

1 Green
2 Red
3 Yellow
4 Ground
5 Ground
6 N/C
7 N/C
8 N/C
9 N/C
10 N/C
11 N/C
12 N/C
13 N/C
14 Ground
15 Ground

Example: To activate the red tally light, connect pin 2 to
pin 4, 5, 14, or 15.

Mounting Holes

4

A VESA-standard 75 mm hole pattern is provided to
accommodate a variety of custom mounting options.

Video Configuration Submenu

■

Color Temperature Presets

Use this setting to choose one of three color temperature presets:

• D55 (5500K)

• D65 (6500K)

• D93 (9300K)

• USER (Adjustable Color Bias and Gain)

■

Adjusting Color Bias

Color Bias Menu

Use this submenu to adjust bias of the color response. Adjust the bias for each color to alter the white balance of the
image. The Color Temperature preset will automatically switch to USER when Color Bias settings are adjusted. It is
normal for color bias adjustments to be very subtle.

■

Adjusting Color Gain

Color Gain Menu

Use this submenu to adjust gain of the color response. The Color Temperature preset will automatically switch to
USER when Color Gain settings are adjusted.

6

11

MARKER SETUP SUBMENU (continued)

On-Screen Menu (continued)

Compatible Input Formats

■

4:3 Markers

Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode. This setting is disabled when the
aspect ratio is set to 16:9, or when Pixel-to-Pixel™, Underscan, or H/V Delay is enabled.

• OFF (No Marker)

• 95% Safe Area

• 93% Safe Area

• 90% Safe Area

• 88% Safe Area

• 80% Safe Area

4:3 Marker Examples:

OFF (No Marker) 90% Safe Area

■

Marker Background

Use this setting to choose how selected markers are displayed on the screen:

Format Composite S-Video YPbPr SDI VGA DVI-D

NTSC
PAL
480i / 59.94
576i / 50
485p / 59.94
576p / 50
1035i / 60
1035i / 59.94
1080i / 60
1080i / 59.95
1080i / 50
1080psF / 24
1080psF / 23.98
1080p / 30
1080p / 29.97
1080p / 25

● ●

● ●

● ●

● ●

● ● ●

● ● ● ●

● ●

● ●

● ● ● ●

● ● ● ●

● ● ● ●

● ● ● ●

● ● ● ●

● ●

● ●

● ●

• OFF The marker is superimposed on the complete image.

• Half-tone Image area beyond the marker is shown at 50% intensity.

• Black Image area beyond the marker is shown at 0% intensity (black).

Example (80% Marker in 4:3 Mode):

Background OFF Half-tone Background Black Background

■

Center Marker

Use this setting to display a center marker on the screen. This feature is not available when H/V delay is on.

720p / 60
720p / 59.94
720p / 50
720p / 30
720p / 29.97
720p / 25
640 x 480 @ 60Hz
640 x 480 @ 75Hz
640 x 480 @ 85Hz
800 x 600 @ 60Hz
800 x 600 @ 75Hz
800 x 600 @ 85Hz
1024 x 768 @ 60Hz
1024 x 768 @ 75Hz
1024 x 768 @ 85Hz

1280 x 1024 @ 60Hz

● ● ● ●

● ● ● ●

● ● ● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

● ●

●

●

Center Marker

10

7

On-Screen Menu

On-Screen Menu (continued)

STRUCTURE OVERVIEW

MARKER SETUP

VIDEO CONFIG

MAIN

MARKER 16:9

MARKER 4:3
MARKER BACKGROUND

CENTER MARKER
COLOR TEMP

ADJ COLOR BIAS

ADJ COLOR GAIN

MONO
BLUE ONLY
PIXEL TO PIXEL
ASPECT RATIO
SCAN
DELAY
SMPTE BAR

FUNCTION 1

OFF, 13:9, 14:9, 4:3, 2.35:1,

1.85:1, 95%, 93%, 90%,
88%, 80%

OFF, 95%, 93%, 90%, 88%,
80%

OFF, HALF, BLACK
OFF, ON
D55, D65, D93, USER
RED (0-100)
GREEN (0-100)
BLUE (0-100)
RED (0-100)
GREEN (0-100)
BLUE (0-100)
OFF, ON
OFF, ON
OFF, ON
4:3, 16:9
NORMAL, UNDER
OFF, H/V, V, H
OFF, ON

DELAY, RATIO, BACK,
CENTER, MARKER, MONO,
CTEMP, PTP

MARKER SETUP SUBMENU

Marker Setup Submenu

■

16:9 Markers

Use this setting to superimpose one of 10 markers on the screen when in 16:9 mode. This setting is disabled when the
aspect ratio is set to 4:3, or when Pixel-to-Pixel™, Underscan, or H/V Delay is enabled.

• OFF (No Marker)

• 13:9 Aspect Ratio

• 14:9 Aspect Ratio

• 4:3 Aspect Ratio

• 2.35:1 Aspect Ratio

• 1.85:1 Aspect Ratio

• 95% Safe Area

• 93% Safe Area

• 90% Safe Area

• 88% Safe Area

• 80% Safe Area

SYSTEM CONFIG

FUNCTION 2

STATUS DISPLAY

LOAD CONFIG

SAVE CONFIG

DELAY, RATIO, BACK,
CENTER, MARKER, MONO,
CTEMP, PTP

OFF, ON

USR1, USR2, USR3, USR4,
USR5, USR6, MFG

USR1, USR2, USR3, USR4,
USR5, USR6

MAIN MENU AND NAVIGATION

Access the main menu by pushing and holding the MENU button on the front panel of the monitor until the main menu
appears (approximately 1-2 seconds).

• Step through menu items using the ↑ and ↓ buttons.

• Choose a menu item by pressing SELECT.

• Rotate through options using the ↑ and ↓ buttons.

• Choose a setting by pressing SELECT.

• Return to the previous menu by pressing MENU.

• Exit the main menu by pressing MENU. The menu will automatically
time out after 5 seconds. After exiting the menu, wait 1-2 seconds
before displaying the menu again.

Main Menu

16:9 Marker Examples:

OFF (No Marker)

8

90% Safe Area

4:3 Aspect Ratio Marker2.35:1 Aspect Ratio

9