Marshall Amplification NN4A, NN4C, NN4D, NN5, NN5A Owner's Manual

HEATED DISPLAY CABINET MARSHALL

MODEL:

NN4A, NN4C

MODEL:

NN5, NN5A

OWNER'S
MODEL NN4A, NN4C, NN4D, NN5 AND NN5A MANUAL

Supplier Name: MARSHALL AIR SYSTEMS, INC.
Address: 419 Peachtree Drive South
Charlotte, NC 28217
Serial #: ____________________________
____________________________
____________________________
Date Received: ____________________________
Date Installed: ____________________________
Telephone #: [phone]
Customer Service #: 800-722-3474
Fax #: [phone]
Service Referral #: 800-722-3474
Local Service Name: ____________________________
Local Service #: ____________________________

(NN4D-WITH OPTIONAL DOORS)

GENERAL SPECIFICATIONS
Model #: NN4A , NN4D NN5

Height: 32-1/2" 16-1/4"
Width: 28" 41"
Depth: 22-1/2" 21-1/4"
Electrical: 110/120volts 110/120 volts (NN5)

7 amps each level 12 amps

International: 220/240 volts (NN4C)

220/240 volts (NN5A)
4 amps 6 amps

Weight: 150 lbs . 110 lbs.

(76 Ibs. for single unit)
Qty of 40
Watt Lights: 8 (4 per level) 6
Power Cord: 8 ft. 3 wire grounding type UL rating

[NN4A comes with (2) power cords]
Approvals: UL and NSF
Options: NN4A can be installed side-by-side instead of
stacked as above picture depicts. Height of non-stacked unit is
16-1/4". Each unit has a separate power cord. Optional 4" legs
also available.

These Heated Display Cabinets feature Marshall's own ThermoGlo™ heating technology. Heat radiates from
every square inch of the upper flat plate heating surfaces. This eliminates the need to clean intricate calrod,
wire and reflector assemblies. A precision microprocessor-type digital display and digital "set point " temperature
controller maintain consistent product temperature.

111019NN4 RV102199
Copyright @ 1994 Marshall Air Systems, Inc.
All Rights Reserved.

MANUFACTURER'S DESCRIPTION

MODEL NN4A, NN4C, NN4D, NN5 AND NN5A

INSTALLATION

1. Unpack unit and remove all protective paper or plastic covering from metal parts.

2. Place cabinet on stable base. Make sure cooling air inlets, next to temperature controller, are not
blocked.

3. The unit should be caulked to the counter top as required by health department codes, or the
optional 4" legs (item 31 on page 4) should be ordered.

4. Install 40 watt coated lights which were shipped loose.

5. Plug unit into an AC 120V receptacle. The 220V International version of unit is furnished with cord
only.

DAILY CHECKLIST AND CLEANING GUIDE

OPENING CHECKLIST

1. Turn on the power switch. The unit is ready to use after a 30 minute preheat period.

2. The temperature controller on the unit is factory set for 450°F (232°C). With the control "ON", the

actual temperature is displayed. The face plate of the control is either black or gray. The range of
set points available is from 400°F (204°C) to 450°F (232°C). The set point may be verified or
changed as follows:

IF BLACK: depress the set button to view the set point. To change set point, use Up/Down arrow
to select new set point while holding set button down.

IF GRAY: depress the set button and RELEASE to view set point. To change set point, push "set"
and, within three seconds, use Up/Down arrow to select new set point.

CAUTION: PRESS ONLY WITH SOFT PART OF FINGER " DO NOT PUSH WITH SHARP
OBJECT.

3. In normal operation, the digital controller will display a value of approximately 480°F (248°C) high

to 430°F (221°C) low.

CLOSING CHECKLIST

1. Turn off the unit and allow it to cool for 20 minutes.

2. Pans and wire grates should be remove d, washed in mild multi-purpose detergent, rinsed and
sanitized.

3. Clean unit and base with a damp cloth or non-abrasive cleaner.

DO NOT IMMERSE UNIT IN WATER! DO NOT USE CAUSTIC CLEANING SOLUTIONS!

4. Allow sufficient drying time before attempting to us e.

2

MODEL NN4A, NN4C, NN4D, NN5 AND NN5A

PREVENTIVE MAINTENANCE

Follow the daily schedule; there are no adjustments. The only user-replacement items are the light bulbs located
under the top cover. If these fail, do the following:

1. Unplug the unit.

2. Remove the bulb(s) by carefully unscrewing them from their sockets.

3. Replace the bulb(s) with a manufacturer's approved replacement part. (See parts list pages 4 & 5.)

4. Check air flow through unit by feeling for air draw at slots on each side of temperature controller.

TROUBLE SHOOTING CHART
Identify problem in the left column and look for probable cause and solution in right hand column. Probable

causes listed in the order they are most likely to happen. This sequence should be used to isolate the problem.

Problem Probable Cause Solution

1. No Light/No Heat Unplugged Circuit breaker is
tripped

2. No Light/With Heat Light bulbs burned out Light switch
defective

3. Temperature Controller Flashing

999

4. Temperature Controller Displays

Less Than 400°F (204°C)

5. Low Product Temperature Set point too low Excessive air draft Reset to 450°F(232°C) Move unit or

*Defective temperature controller or
sensor

*Loose sensor or defective heating unit
assembly

Plug in Reset breaker - call
electrician if tripped twice Call

Unplug unit and replace bulbs Call
Marshall Customer Service

Call Marshall Customer Service
Call Marshall Customer Service

shield draft

* NOTE: When replacing sensor, a special heat sink sealant will be present when removing failed sensor.

Applying new sealant is not required; however, be sure to utilize existing sealant when mounting new
sensor.

3

MODEL NN4A, NN4C, NN4D, NN5 AND NN5A

N/A

118771

Mirror Mounting Kit

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION

1 110833 Shelf Runner (2 Required) 18 502206 Transformer 120V to 12V
2 501484 Screw #1 0 X.500" * 501958 Transformer 240V to 120V
3 502064 Sensor, RTD Temperature * 502168 Transformer 240V to 12V
4 111194 Sensor Guard (T'Glo 20" X 14") 19 114541 Temperature Controller RTD
5 111192 Joining Tab (4 Required) 20 * 132499 Temp Controller RTD (°C)
6 502108 Bushing 9/32" Dia. 21 500340 Terminal Strip 3 Pole
7 501684 Screw #10-24 X.750" 22 112925 T'Glo 20" X 14"-120V
8 111024 Swing Cover Plate 111866 T'Glo 20" X 14"-220V
9 502083 Nylon Washer 23 501885 Label: CAUTION HOT (not shown)
10 111196 Heat Deflector 24 502080 Strain Relief
11 501864 Switch Rocker 25 111380 Door Assembly
12 501507 Screw #10-24 X.500" 26 111387 Door Guide Assembly (right
13 111195 Faceplate Standoff 111388 Door Guide Assembly
14 110042 Fan (left not shown)
15 501865 Lamp Holder 27 111186 Cord With Plug
16 502239 Bulb Tuffskin 40 Watt 28 110904 Cover-Side Panel Right
17 110912 Cover-side Panel-Left (no hole)

29 111187 Cover-Side Panel Right
(with hole)
30 110826 Control Front Panel
31 500263 4"Leg(1)

* These parts are for International (220V, 240V)
units only.

OPTIONAL:

N/A 119844 Side swing Doors (Pair)

N/A 503413 Kit, Temp. Control Faceplate

Deg F REF: 132574

4

N/A

120456

Side swing Doors (Pair)

Deg F REF:

132574

MODEL NN4A, NN4C, NN4D, NN5 AND NN5A

ITEM PART# DESCRIPTION ITEM PART # DESCRIPTION
1 110903 Shelf Runner (2 Required) 17 501507 Screw #10-24 X.500"

2 501484 Screw #1 0 X.500" 18 502080 Strain Relief
3 502108 Bushing 9/32" Dia. 19 110042 Fan
4 502064 Sensor, RTD Temperature 20 110904 Cover-Side Panel Right
5 111310 Sensor Guard (T'Glo 10" X 14") 21 500340 Terminal Strip 3 Pole

6 111547 Door Assembly (Includes 22 502206 Transformer 120V to 12V

Handle, No Guides) * 501958 Transformer 240V to 120V

7 501885 Label: CAUTION HOT * 502168 Transformer 240V to 12V
8 111310 Sensor Guard (TGIo 20" X 14") 23 N/A Obsolete Part
9 502083 Nylon Washer 24 111286 T'Glo 20" X 14"-120V
10 114541 Temperature Controller RTD

114433 T'Glo 20" X 14"-220V
11 501684 Screw #10-24 X.750" 25 501865 Lamp Holder
12 111024 Swing Cover Plate 26 502239 Bulb Tuffskin 40 Watt
13 111387 Door Guide Assembly (right shown) 27 110915 T'Glo 10" X 14"-120V

14 110895 Control Front Panel 114434 T'Glo 10" X 14"-220V
15 114578 Cord with Plug 28 110912 Cover-Side Panel-Left

16 501864 Switch Rocker 29 111388 Door Guide Assembly

(left shown)

* These parts are for International (220V, 240V)
units only.

OPTIONAL:

N/A 118772 Mirror Mounting Kit
N/A 503413 Kit, Temp. Control Faceplate

5

MODEL NN4A, NN4C, NN4D, NN5 AND NN5A

LIMITED WARRANTY

MARSHALL AIR SYSTEMS, INC., ("Marshall") warrants to the first purchaser ("Purchaser") all new equipment of its
manufacture to be free of defects in material and factory workmanship for a period of one year from date of shipment
provided that (i) the equipment is installed in the Continental United States, Canada or Hawaii and operated according to the
Owner's Manual while located at the original address of installation, (ii) the warranty registration card has been completed
and returned to the factory within fifteen (15) days after installation, and (iii) a post -installation start-up has been performed by
an authorized service representative (portable equipment not applicable). Marshall's obligation under this warranty is limited
to the repair or replacement at its option of any defective part. Under certain circumstances, Marshall will reimburse
Purchaser for limited labor costs in replacing parts during a period of not more than ninety (90) days from date of shipment,
provided that Labor Reimbursement instructions are followed and items i, ii, and iii above are completed. See special
provision for portable equipment. It is understood that Marshall's obligation with respect to equipment located outside the
Continental United States, Canada or Hawaii is limited to replacement parts only.

Because Marshall does not and cannot control Purchaser's installation, use, and maintenance of equipment
manufactured by Marshall, this warranty DOES NOT COVER:

1. Any equipment calibration;

2. Any component disassembled in the field;

3. Damage due to improper cleaning and/or abuse, i.e. burner rotation, grease accumulation in electrical
components or plugs (hosing or "watering down" equipment will cause electrical failures not covered by
warranty);

4. Blown fuses or bulbs, motor brushes, and Teflon components;

5. Any replacement parts used on the equipment which are not purchased from Marshall;

6. Accessory components not installed and/or manufactured by Marshall.

Shipping damage must be reported to the carrier and is not covered under this warranty. Marshall will not be liable for
damage as a result of improper installation, misuse, abuse, alteration of original design, incorrect voltage, unauthorized
service, breakage of fragile items, or any other damage caused by an act out of Marshall's control.

The effect of corrosion, fire, and normal wear on the equipment or component parts is not covered by this warranty. This
warranty does not cover cooking performance, smoke capture or holding temperatures which is a function of food types,
textures, temperatures, equipment line ups and other variables chosen by the Purchaser and over which Marshall has no
control. This warranty does not apply to damage caused by accident or to damage caused by the negligence of Purchaser or
the employees of Purchaser or to damage caused by lightning generated electrical current or any other Act of God
whatsoever. This warranty does not apply to any equipment bearing a serial number which has been tampered with or
altered. Marshall reserves the right to accept or reject any such claim in whole or in part. Marshall will not accept the return of
any product without prior written approval from Marshall, and all such approved returns shall be made at Purchaser's sole
expense.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE,
OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT, AND EXCEPT FOR THE EXPRESS
WARRANTY CONTAINED HEREIN, THE EQUIPMENT IS SOLD "AS IS." REMEDIES UNDER THIS WARRANTY AND
UNDER ANY WARRANTY THAT MAY SURVIVE THE DISCLAIMER OF WARRANTIES ARE LIMITED EXCLUSIVELY TO
THOSE REMEDIES DESCRIBED ABOVE. NO OTHER REMEDY IS AVAILABLE UNDER THIS WARRANTY OR ANY
OTHER WARRANTY. NEITHER THIS WARRANTY NOR ANY OTHER WARRANTY COVERS, AND MARSHALL WILL
NOT BE RESPONSIBLE FOR, ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED
TO THE COST OF DISASSEMBLY AND SHIPMENT OF THE EQUIPMENT, PRODUCTION OR PRODUCT LOSSES,
INJURY TO OTHER PROPERTY, OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE
PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER
PRODUCT OR GOODS, OR OTHER LOSSES. WHERE, DUE TO OPERATION OF LAW, CONSEQUENTIAL AND
INCIDENTAL DAMAGES CANNOT BE EXCLUDED, THEY ARE EXPRESSLY LIMITED IN AMOUNT TO THE PURCHASE
PRICE OF THE EQUIPMENT.

FOR INTERNATIONAL INSTALLATIONS " PLEASE CONTACT YOUR LOCAL MARSHALL AIR
SYSTEMS RECOGNIZED DISTRIBUTOR.

7

MODEL NN4A, NN4C, NN4D, NN5 AND NN5A

WARRANTY PROCEDURES

RETURN GOODS AUTHORIZATION FOR PARTS - FACTORY DIRECT

For prompt warranty parts replacement and RGA processing, please call Marshall's Customer Service Department at
800-722-3474 or 704-525-6230 for assistance. In all cases, a Return Goods Authorization (RGA) number must be
issued by Marshall Air Systems, Inc. Unauthorized returns will not be processed.

Option #1: Purchaser to return part prepaid to Factory, Marshall to repair or replace at own expense if defective, and

ship part back to Purchaser prepaid.

Option #2: Marshall to furnish replacement part freight prepaid with or without requesting return of the defective part.

WARRANTY LABOR REIMBURSEMENT AND/OR PARTS REPLACEMENT THROUGH RECOGNIZED
SERVICE AGENCY

To be reimbursed for warranty labor costs, authorization must be given by Marshall Air Systems, Inc. Unauthorized
work will not be reimbursed. Work must be performed by a Marshall Air Systems Recognized Service Agency within
the service time allowance guidelines and must be submitted along with failed parts (if applicable) to Marshall Air
Systems (freight prepaid) within 30 days of the work being performed. Travel is covered, but must not exceed 50
miles or 1 hour, whichever is greater. Call Marshall's Service Department at 800-722-3474 or 704-525-6230 with any
questions. Service is to be performed by recognized service agencies during normal working hours. Owner to pay for
all other charges including excessive travel or overtime charges. DIAGNOSTIC LABOR CHARGES ARE
INCLUDED IN SERVICE TIME ALLOWANCE GUIDELINES. All portable equipment (under 90 pounds) shall be
delivered by Purchaser, at his/her expense, to the nearest authorized service agency for in-shop repair or at
Purchaser's discretion he/she will pay all travel time and mileage expenses for portable equipment.

NON-WARRANTY RETURNS:

All items returned for customer convenience are subject to a 20% restocking fee. In the event of an error by Marshall
Air Systems, Inc., a Returned Goods Authorization will be issued for full credit.

FOR INTERNATIONAL INSTALLATIONS - PLEASE CONTACT YOUR LOCAL MARSHALL AIR
SYSTEMS RECOGNIZED DISTRIBUTOR.

8