Marshall Amplification CV503, CV346, CV344, CV506 User Manual

Download

Broadcast A/V Division

CV503, CV506, CV344, CV346

Compact & Miniature Full-HD Cameras

User Manual

Table of Contents

CV503/CV506/CV344/CV346 Manual

1. General Information

Thank you for your purchase of a Marshall Miniature or Compact Camera.

The Marshall Camera team recommends thoroughly reading this guide for a deep understanding of on-screen-display (OSD) menus, breakout cable operation, settings adjustment explanation, troubleshooting, and other critical information.

Table of Contents

1. General Information

2. Menu Structure

3. OSD Joystick and Button

4. WB Control

5. AE Control

6. Day / Night

7. Audio

8. Image Control

9. Special

10. Setup

Please carefully remove all contents of box, which should include the following components:

CV503/CV506 includes:

• Camera with 3.6mm lens (interchangeable)

• Camera Breakout Cable (Power/RS485/Audio)

• 12V Power Supply

CV344/CV346 includes:

• Camera with CS/C mount (lens sold separately)

• Camera Breakout Cable (Power/RS485/Audio)

• C-Mount Lens Adapter (only used when using C-Mount lens)

• 12V Power Supply

The CV503/506 ships with a 3.6mm (72°AOV) M12 lens installed and is interchangeable to any number of Marshall M12 lenses.

The CV344/346 Camera utilizes a CS/C lens mount and does not include a stock CS/C Lens. CS/C mount lenses are sold separately, as well as adapters to other lens mount types.

11. Reset

12. E xit

13. Troubleshooting

Warranty

END

Each camera comes set to default at 1920x1080p @ 30fps out of the box; which can be changed in the OSD Menu to a variety of resolutions and framerates.

If the camera is accidentally changed to a resolution or framerate that your monitor or equipment doesn’t accept, please follow the instructions below to reset camera to factory default:

1. Plug the camera into power source and connect breakout cable to rear camera panel (locking connection), Power LED should illuminate.

2. Push OSD joystick button UP, DOWN, UP, DOWN and PUSH and HOLD for ﬁve seconds.

3. Camera should reset to 1920x1080p @ 30fps.

4. If camera does not reset, repeat steps after a power-cycle.

www.marshall-usa.com1 2

CV503/CV506/CV344/CV346 Manual

2. Menu Structure

SETUP SUB MENU SUB MENU

WB CONTROL

AE CONTROL

DAY / NIGHT

ATW

ONE PUSH

INDOOR

OUTDOOR

MANUAL

AUTO

LENS MODE (DC IRIS ONLY)

SHUT FIX

AGC FIX

LENS MODE (DC IRIS ONLY)

MANUAL

LENS MODE (DC IRIS ONLY)

DAY

NIGHT NIGHT COLOR

BLUE

RED

AGC MAX

SENS UP

AE BRIGHT

FLK CONTROL

SHUTTER

AGC MAX

SENS UP

AE BRIGHT

FLK CONTROL

AGC

AE BRIGHT

FLK CONTROL

SHUTTER

IRIS

AGC

FLK CONTROL

SETUP SUB MENU SUB MENU

AUDIO

SAMPLE BITS

LENS SHADING

CONTRAST

BRIGHTNESS

SATURATION

HUE

EDGE ENHANCE

IMAGE CONTROL

AUTO SATURATE

AUTO EDGE

BLACK WHITE LEVEL

GAMMA CORRECT

DNR

DZOOM

DEFOG

DIS

BACKLIGHT

BINNING

SPECIAL

DEFECT PIXEL

DISP FUNCTION

WDR

FLICKER DETECT

PRIVACY

CAM TITLE

COMMUNICATION RS-485/ID

SETUP

SYSTEM INFO

OUTPUT FORMAT

DNR MODE

DNR LEVEL

AUDIO

MIC/LINE

AUDIO LEVEL

MIC ATTENUATOR

RESET USER/FACTORY

EXIT

www.marshall-usa.com3 4

CV503/CV506/CV344/CV346 Manual

503

344

506

346

RS485

AUDIO IN

POWER

Use the UP & DOWN

buttons to select the

desired item.

Use the LEFT & RIGHT

buttons to change the

sub-item.

> Icon indicates “Press OSD button” or “Enter Sub Menu”

3. OSD Joystick and Button

4. WB CONTROL

Select WB CONTROL using the UP or DOWN button. You can change between AUTO, ATW, PUSH, and MANUAL using the LEFT or RIGHT buttons.

• ATW : Continuously adjusts camera color balance in accordance with any change in color

temperature. Compensates for color temperature changes within the range of 1,900°K to

11,000°K.

• ONE PUSH: Color temperature will be manually adjusted by pushing the OSD button. Place

the white paper in front of the camera when OSD button is pressed to obtain optimum result.

• MANUAL: Select this to ﬁne-tune White Balance manually.

You can adjust the blue and red tone level manually.

1. BLUE: Adjust the Blue tone of the image. (0~100)

2. RED: Adjust the Red tone of the image. (0~100)

• INDOOR: Select this to adjust white balance to indoor lighting condition.

• OUTDOOR: Select this to adjust white balance to outdoor lighting condition.

I/O Cable (included in box) for CV503, CV506, CV344, CV346

1. SET Used to access the menu and confrim selection.

2. UP Used to move the cursor up.

3. DOWN Used to move the cursor down.

4. LEFT Used to move the cursor left and change the value

5. RIGHT Used to move the cursor to the right and change the value.

Press SET button to access the Main Menu

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET

> > > > > > > >

EXIT

MENU WB CONTROL

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET

> > > > >

MODE PUSH BLUE RED

RETURN > > >

MANUAL

50 50 >

EXIT

1. Adjust White Balance ﬁrst by using the ATW mode before switching to MANUAL mode.

2. White Balance may not work properly under the following conditions. In this case, select the ATW mode.

• When the ambient illumination of the subject is dim.

• If the camera is directed towards a ﬂuorescent light or is installed in place where illumination changes dramatically, the White Balance operation may become unstable.

www.marshall-usa.com5 6

CV503/CV506/CV344/CV346 Manual

5. AE CONTROL

Select AE CONTROL using the UP or DOWN button. You can select one sub-mode using the UP or DOWN buttons.

MENU AE CONTROL

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

• AUTO: Adjusts the exposure level automatically. Detailed ﬁne tuning options are available

under this menu.

• SHUT FIX: Provides more detailed shutter speed options. All other controls are tuned for the

selected shutter speed.

• AGC FIX: Provides more detailed gain option. All other controls are tuned for the selected gain

> > > > > > > >

AE MODE SHUTTER IRIS AGC AGCMAX SENS UP AE BRIGHT FLK CONTROL LENS MODE RETURN

AUTO

13 OFF 6 OFF

6. DAY / NIGHT

Select DAY / NIGHT using the UP or DOWN button. You can select one sub-mode from AUTO, COLOR, and NIGHT using the UP or DOWN buttons.

MODE: Set camera to either color mode or B&W mode. (Day, Night)

DAY: When set to DAY mode, camera stays in color and IR cut ﬁlter is engaged.

NIGHT: When set to NIGHT mode, camera stays in B&W and IR cut ﬁlter is removed.

• NIGHT COLOR: When on, camera stays on color mode. Night (B&W) can be selected from

this mode. (On, Off)

MENU DAY/NIG HT

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

> > > > > > > >

MODE NIGHT COLOR RETURN

DAY (COLOR)

value.

• MANUAL: Adjusts the exposure level manually

1. SHUTTER: Speed can be set at auto or manual. (1/30~1/10,000)

2. IRIS SPEED: Electronic Iris speed can be controlled, for DC Iris lens only. (0~5)

3. AGC: Electronic Iris speed can be controlled, for DC Iris lens only. (0~5)

4. AGC MAX: Used to set maximum gain value to control the video noise caused by Auto

Gain Control. (Off, Low, Middle, High, DMIN, DMID, DMAX)

5. SENS UP: Controls the digital slow shutter to allow extra light into the camera and adjust

the picture quality. (Off, x2~x10)

6. AE BRIGHT: Select this to adjust auto exposure brightness levels. (0~10)

7. LENS MODE: Lens setting will be optimized for selected environment, for DC Iris lens only.

8. FLK CONTROL: Provides a proper image sensor frequency to match the power frequency

in order to minimize video ﬂicker.

www.marshall-usa.com7 8

CV503/CV506/CV344/CV346 Manual

7. AUDIO

Select AUDIO using the UP or DOWN button and enter ON using SEL button. You can select one sub-mode using the UP or DOWN buttons.

• MIC / LINE: Select MIC or LINE for the audio input source.

• AUDIO LEVEL: Select this to adjust audio levels manually.

• MIC AT TENUATOR : Audio attenuation can be controlled from this menu to minimize the

audio noise level

1. SAMPLE BITS: Select the bit depth of audio

MENU AUDIO

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

> > > > > > > >

MODE AUDIO LEVEL MIC AT TENUATOR AGC LIMIT SAMPLE BITS RETURN

OFF 0 dB OFF

24 BITS

8. IMAGE CONTROL

Select IMAGE CONTROL using the UP or DOWN button. You can select LENS SHADING, CONTRAST, HUE, And EDGE ENHANCE using the UP or DOWN buttons.

MENU IMAGE CONTROL

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

• LENS SHADING: Corrects inconsistent brightness level in the image.

• CONTRAST: Adjust the image contrast level.

• BRIGHTNESS: Adjust the image brightness level.

> > > > > > > >

LENS SHADING CONTRAST BRIGHTNESS SATURATION HUE EDGE ENHANCE AU TO SATUR ATE AUTO EDGE BLACK WHITE LV GAMMA CORRECT DNR RETURN

OFF 11 11 10 0 5 MIDDLE ON > DEFAULT >

• SATUR AT ION : Adjust the image saturation level.

• HUE: Adjust the image hue level.

• EDGE ENHANCE: Adjust the image sharpness level.

• AU TO S ATURAT E : Decrease saturation automatically when noise scene is detected.

• AUTO EDGE: Adjust line sharpness level automatically.

• BLACK WHITE LEVEL: Adjust the image black level value.

• GAMMA CORRECT: Adjust the image output gamma level.

• DNR: Reduces video noise at low ambient light.

Select the DNR level from OFF, LOW, MIDDLE, and HIGH using the LEFT or RIGHT button.

www.marshall-usa.com9 10

CV503/CV506/CV344/CV346 Manual

9. SPECIAL

Select SPECIAL using the UP or DOWN button. You can select DEFOG, MOTION DETECT, BACKLIGHT, DEFECT PIXEL, and FLICKER DETECT using the UP or DOWN buttons.

MENU SPECIAL

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

> > > > > > > >

DZOOM DEFOG DIS BACKLIGHT BINNING DEFECT PIXEL DISP FUNCTION WDR FLICKER DETECT PRIVACY RETURN

OFF OFF OFF OFF OFF ON > OFF OFF >

10. SETUP

CAMERA setup can be adjusted from this menu. You can select CAMERA ID, Communication, System Info, and Output Format using the UP or DOWN buttons.

MENU SETUP

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

> > > > > > > >

CAM TITLE COMMUNICATION SYSTEM INFO OUTPUT FORMAT RETURN

OFF > > 1080p 59.94 >

• DZOOM: Digitally zoom the video by the desired ratio.

• DEFOG: This feature will help increase visibility in extreme weather conditions, such as fog,

rain or in a very strong luminous intensity.

• DIS: This feature enables digital image stabilization

• BACKLIGHT: Adjust backlight compensation by choosing either BLC HLM from this menu.

• BINNING: Enable or disable pixel binning.

• DEFECT PIXEL: Advanced defective pixel correction menu.

• DISP FUNCTION: Display effect such as freeze mirror, rotation, and style can be applied from

this menu.

• WDR: This feature enables user to view both object and background more clearly when

background is too bright.

• FLICKER DETECT: Adjust the image sensor frequency to match the power frequency.

• PRIVACY: Mask an area you want to hide on the screen by applying the privacy zones.

• CAM TITLE: Camera title can be turned ON or OFF.

• COMMUNICATION: VISCA communication can be adjusted.

1. CAM ID: Camera ID can be setup. (0~7)

2. ID DISPLAY: Camera ID display can be displayed.

3. BAU DRATE : Camera baudrate can be set.

(2400, 4800, 9600, 19200, 38400)

• SYSTEM INFO: Camera information can be found under this menu.

• OUTPUT FORMAT: Camera resolution and frame rate can be set.

(1080 by default)

Select the FRAME RATE using the LEFT or RIGHT buttons. Available Frame Rates are: 1920 x 1080p 60, 59.94, 50, 30, 29.97, 25, 24, 23 1920 x 1080i 60, 59.94, 50 1280 x 720p 60, 59.94, 50

www.marshall-usa.com11 12

CV503/CV506/CV344/CV346 Manual

11. RESE T

Select RESET using the UP or DOWN buttons.

• RESET: Reset the camera settings the factory defaults or user setting value.

MENU RESET

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

> > > > > > > >

RESET MODE RESET SAVE AS USER RETURN

FACTORY >

12. EXIT

Select EXIT using the UP or DOWN button.

WB CONTROL AE CONTROL DAY/N IGHT AUDIO IMAGE CONTROL SPECIAL SETUP RESET EXIT

• SAVE: Exit the setup after saving the value changes.

> > > > > > > >

• ON: Set the camera setting to either “FACTORY” or “USER” of “CHANGE” menu. Make sure

to select the right mode from “CHANGE” before defaulting the camera.

• RESET MODE: Select the desired setting mode.

Select from USER or FACTORY using the LEFT or RIGHT button.

1. USER: Select “USER” if setting value user saved last is needed.

2. FACTORY: Select “FACTORY” if factory default setting is needed.

“FRAME RATE”, “CAM ID”, and “BAUDRATE” will note change.

www.marshall-usa.com13 14

13. TROUBLESHOOTING

Before sending the camera for repair, please check below to make sure that the camera is installed correctly. If it still does not perform adequately, please consult with your supplier.

Problem Solutions

a. Check that all connected devices are powered on.

Nothing appears

on the screen.

The picture is

not clear.

b. Confirm that the voltage is correct. c. Confirm that the power supply provides enough current to power the camera. d. Check that all video cables are correctly connected.

a. Check that your monitor is correctly adjusted. b. Confirm that the glass in front of the lens is clean. If there is dust, dirt, or fingerprints on the glass, the image quality will be affected. To clean the glass, use a soft, dry, and non-abrasive cloth or a commercially available lens cleaning set. c. Correctly adjust the focus.

Warranty

Marshall Electronics warranties to the ﬁrst consumer that this device will, under normal use, be free from defects in workmanship and materials, when received in its original container, for a period of two years from the purchase date. This warranty is extended to the ﬁrst consumer only, and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or modiﬁcations in design or construction void this warranty. No sales personnel of the seller or any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.

Due to constant effort to improve products and product features, speciﬁcations may change without notice.

The picture has

interference.

The picture is

flickering

continually.

The camera is not

synchronizing with

the reference signal.

a. The camera may be close to a high voltage source, such as a power generator. b. The BNC cable is not terminated properly. c. The video cables are not connected properly.

a. Check the termination and set the impedance at 75 properly. b. Ensure that the camera is not pointing towards the Sun or any light source. c. Check if there is any intermediate device. d. Check if the distance of the video cable exceeds the maximum transferable limitation.

a. Make sure Tri-Level reference signal is used. b. Locking takes up to 1 minute depending on the signal strength. Make sure the sync LED is solidly lit. c. Check if the cable and connectors used in reference sync are in good condition. d. Make sure the cable length used in reference sync does not exceed 100 ft. e. Make sure OUTPUT EN is on when using the genlock output.

20608 Madrona Avenue, Torrance, CA 90503

Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688

www.marshall-usa.com

support@marshall-usa.com

NB0 60419a

Marshall Amplification CV503, CV346, CV344, CV506 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual