Marshall Amplification CV350-5X, CV350-5XB User Manual

1080 HD-SDI

5X Autofocus Lens Day/Night Camera

Design and specifications are subject to change without notice.

Panasonic 2.3 Megapixel CMOS
5x Optical Zoom, F=4mm ~ 20mm, F2.8 ~ F3.9
HD-SDI(BNC), HDMI, and Analog CVBS (BNC)

0.2Lux (Color), 0.1Lux (B/W), 0.005Lux (DSS On)

Optical Multi Coated ICR Filter
3D-DNR, Privacy masking
Defog, HLC, WDR
Full OSD control
12VDC

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.

PRECAUTIONS

REGULATORY NOTICE

FEATURES

HARDWARE OVERVIEW: Front SPECIFICATIONS

DIMENSIONS

WARNING

!

Do not use the camera if fumes, smoke o r a strange odor is emitted
from the unit, or if it seems to not func tion correctly. Disconnect t he
power source immediately and consul t your supplier.

CAUTION



Always follow the instructio ns in the installation guid e when
applying power. Fire and equipmen t damage can occur if power
is applied incorrectly. For the correc t power supply, refer to the

CAUTION



Do not install or operate in small, u nventilated areas. Heat buil d up

CAUTION



To prevent damage, do not drop the camera or subject it to strong

CAUTION



If installed close to a TV, radio transmitter, magnet, e lectric motor

interfere with or distort the image.

CAUTION



Whether or not the camera is used outdoo rs, never point it toward
the sun. Use caution when operating the ca mera in the vicinity of spot

CAUTION



Do not use the camera in extreme e nvironments where high
temperatures or high humidi ty exists. Use the camera und er
conditions where temperatures a re between 14°F ~ 122°F (-10°C ~
50°C), and humidity is below 90% .

shock or vibration.

HARDWARE OVERVIEW: Rear

CV350-5X (Signal type: 1080P25/30, 1080i50/60, 720P50/60, 1080P50/60)
CV350-5XB (Signal type: 1080P29.97, 1080i59.94, 1080P59.94, 720P59.94)

5x Auto Focus Lens

Remote Control IR Receiver

Hole for wall or
ceiling mount

Z/F & Menu
Controls Key

Analog Video Output

HD-SDI Video Output

1. Alarm output for Motion detection

2. External Day/Night input

3. GND

4. RS-485 Remote control: -

5. RS-485 Remote control: +

HDMI Video Output

Power LED Indicator

Power Input

12VDC

Remote Control

IR Receiver

Z/F & Menu Controls Key

MENU On, One Push AF Key

Menu On: Press and hold menu key for 2seconds to display menu.
Menu Mode: To select data or exit from menu, press menu key.
One Push AF: To adjust focus position, press and release menu key when One Push AF mode is enabled.

Focus NEAR: Press and hold right key for continuous optical focus near.
MENU: To change menu parameter, press right key while menu is displayed.

Focus Far: Press and hold left key for continuous optical focus far.
MENU: To change menu parameter, press left key while menu is displayed.

Zoom TELE: Press and hold up key for continuous optical zoom in(Tele).
MENU: To move up menu item, press up key while menu is displayed.

Zoom WIDE: Press and hold down key for continuous optical zoom out(Wide).
MENU: To move down menu item, press down key while menu is displayed.

Image Sensor 1/2.86” Progressive CMOS (Approx. 2.3 mega)
Scanning System 16:9 Progr

essive
Sync. System Internal
Effec

tive Pixel 1920(H) x 1080(V

)

Min. Illumination 0.2Lux (Day), 0.1Lux

(Night), 0.005Lux(DSS on)
Horizontal Resolution 1000TVL
Lens 5x Opti

cal Zoom, F=4.0~20mm, F2.8 ~ F3.9

Zoom 5x optical

zoom + 12x digital zoom = 60x

Focus Near/Far, Au

to/Manual/One Push

Angle of View(H) 64.2 degrees(

WIDE), 13.8 degrees(TELE)
Back Light Compensation WDR/BLC, HLC(High Light compensation)
Exposure A

uto / Manual

White Ba

lance Auto(3,0

00°K~8,000°K) / ATW(1,900°K~11,000°K) / Manual
Day & Night System AGC / TDN(ICR)
E

lectronic Shutter NTSC: 1/30~1/30000, PA

L: 1/25~1/30000, DSS( ~ 1/1sec)

Functions Privac

y Mask, Image Mirror, 3DNR, Flicker-less, Sharpness, Defog

800mVp-p, 75Ω, unb

alanced generator(single-ended)

CVBS (NTSC/ PAL) Analog

Composite(1V ± 0.2 Vp-p) NTSC/PAL

HD Output

HDMI 1920x1080p@59.94, 1920x1080i@59.94,
1920x1080

p@29.97, 1280x720p@59.94
PELCO-P/D, SONY-VISCA protocol
8bits data, 1 stop bit, no parity, 2400~115200bps

D/N input O

PEN(f

loating): Day mode, CLOSE: Night mode

Motion Detection out

High level signal(5VDC) output.
MD output use tr

ansistor, connect lower than 100mA load.
Operation Temperature -10℃ ~ 50℃
Power

Input 12VDC (7V

to 15VDC)

Power consumption Max 6W (4.

8W Lens inactive, 5.5W Lens active)

Weight 274g (0.6L

bs)

Dimensions (D x W x H) 53.7 x 36.3 x 34.8mm (2.11 x 1.42 x 1.37")

RS485

General

Vi

deo

Output

Control
Interface

SMPTE 292M(1.485Gbps): 1080P@29.97, 720P@59.94
SMPTE 424M (

2.97Gbps): 1080P@59.94

Sensor

Optics

Func

tions

SDI Output

Setup Menu of 1080 HD-SDI 5X Auto Focus Camera

Design and specifications are subject to change without notice.

SETUP SUB MENU SUB MENU DESCRIPTION

AWB Controls the automac adjustment of the light source's color temperature to 3,000°K ~ 8,000°K.
ATW

Connuously adjusts camera color balance in accordance with any change in color temperature. Compensates for color temperature changes within the range of

PUSH

Color temperature will be manually adjusted by pushing the OSD buon. Place the white paper in front of the camera when OSD buon is pressed to obtain the

INDOOR Select this when the color temperature is between 4500K and 8500K.

OUTDOOR Select this when the color temperature is between 1700K and 11000K (Ex. Sodium light inclusion)

MANUAL BLUE, RED

Select this to fine-tune White Balance manually. You can adjust the blue and red tone level manually.

INDOOR, OUTDOOR

Select one according to the locaon of camera installaon. Then, select one sub-mode from AUTO, MANUAL, SHUTTER, PRIORITY, IRIS PRIORITY, and BRIGHT.

AUTO

IRIS and SHUTTER are controlled automacally.

MANUAL

IRIS, GAIN, and SHUTTERf are controlled manually.

SHUTTER PRIORITY Manual SHUTTER and GAIN control with automac IRIS control.

IRIS PRIORITY

Manual IRIS and GAIN control with automac SHUTTER control.

BRIGHT

IRIS and GAIN can be controlled by control of BRIGHTNESS.

BRIGHTNESS MANUAL, 0~20

0~20: Adjust the screen brightness. MANUAL: BRIGHTNESS control is fixed, and give the exposure control priority to other resources.

IRIS AUTO, MANUAL, 0~20

0~20: Adjust the IRIS screen brightness. AUTO: IRIS controls exposure automacally but SHUTTER is fixed. MANUAL: IRIS control is fixed, and give the exposure

AGC LIMIT 0~20 A funcon which controls the amplificaon/gain process automacally if the illuminaon falls under the usable level.

SHUTTER AUTO, MANUAL, 1/2~40K

1/2~40K: Adjust the SHUTTER speed. (1/2, 4, 8, 15, 30, 60, 90, 120, 150, 180, 250, 350, 500 , 725, 1000, 1500, 2K, 3K, 4K, 6K, 10K, 20K, 30K, 40K)

DSS(SENS-UP) MANUAL, OFF~1/2

OFF~1/2: Adjust the level of DSS. (OFF, 1/30, 1/15, 1/8, 1/4, 1/2) When it is in low luminance condion, DSS can adjust the picture quality by maintaining the light

FLICKERLESS OFF, ON Use this funcon when you experience picture flicker, this happens when there is a conflict with the installed lighng frequency.

AUTO

Automacally adjusts the focus posion.

MANUAL

Manually adjusts the focus posion when zoom is changed.

PUSH

When this mode is enabled, it will automacally adjusts the focus posion only when the zoom is changed.

ZOOM SPEED 0~7 Set the zoom speed.

TELE LIMIT X3~X60

Set the limit of the tele.

WIDE LIMIT X1~X2

Set the limit of the wide.

FAR END INFINITY, 2, 3, 5, 10M Set the distance limit for the far focusing. The lens moves to adjust the focus from the distance.

NEAR END 30CM , 1, 1.5, 2, 3, 5, 10M Set the priority distance limit for near focusing.

LENS INITIAL OFF, AUTO, ONE PUSH

AUTO: The focus is automacally adjusted at the pre-set interval (01~07). ONE PUSH: The focus is re-adjusted when the OSD buon is pushed over ONE PUSH.

USER PRESET

This funcon is to set user defined zoom and focus posion. Up to 32 preset posion can be set with sub menu, USER PRESET, ACTIVE, SAVE, RESET.

WDR Enable user to view both object and background more clearly when background is too bright. Set the WDR-LEVEL (0~4).

BLC Enable a back light compensaon feature.

SPOT Enables a user to select a desired area on a picture and view that area more clearly when background is too bright.

ACE GAIN Brightness correcon of the dark image area. Adjust the GAIN level (LOW, MIDDLE, HIGH).

LEVEL Highlight the bright

area with a masking box with a selected color. Adjust the masking level (0~20).

COL

OR Select the color for masking (GRN, MAG, RED, BLUE, BLK, WHT, YEL, CYN)

D/N LEVEL

The camera will stay in DAY in a normal environment, but switched to NIGHT mode when ambient illuminaon become this pre-set level.

MARGIN Set the margin between Day →Night switching level and Night →Day switching level. Different exposure gain level is needed to avoid malfuncons.

DWELL TIME Select the checking me of light condion to confirm to chage from the day mode to the night mode.

NIGHT BURST Night burst OFF makes that the color burst is removed when ICR switches to black/white.

DAY The picture is always displayed in color.

N

IGHT N

IGHT BURST The picture is always displayed in black/white.
D/N LEVEL The camera will stay in DAY in a normal environment, but switched to NIGHT mode when ambient illuminaon become this pre-set level.

DWELL TIME Select the interval me from the day mode to the night mode.

NIGHT BURST Alters the color burst informaon passed to the video monitor.

COLOR LEVEL 0~20 Adjust the color level value for a fine

color tune.

SHARP

NESS 0~20 As you increase this value, t he picture outline becomes stronger and clearer.

IMAGE FLIP Video output will be flipped (MIRROR-HORIZONTALLY, FLIP-VERTICALLY, ROTATION).

DEFOG AUTO, MANUAL This feature will help increase visibility in extreme weather condions, such as fog, rain or in a very strong luminous intensity.

3D-DNR OFF, LOW, MIDDLE, HIGH This feature will reduce the video

noise at low ambient light.

M

OTION

This feature will observe the object movement by moon zone and sensivity that are pre-set with sub menu, DET. SIZE, SENSITIVITY, MASK ACTIVE, WIDTH,

SHADING This feature will correct the inconsistent brightness level in the image.
GAMMA This feature will adjust video output brightness (STANDARD, STRAIGHT, LOW, MIDDLE, HIGH).

RESOLUTION

Change video output specificaon. CV350-5X: 1080P25/30, 1080i50/60, 720P50/60, 10 80P50/60. CV350-5XB: 1080P29.97, 1080i59.94, 1080P59.94, 720P59.94

USER TITLE The camera tle can be entered and it will appear over the video output.

ZOOM MAGNIFICATION Turn On or off of the zoom scale display.

PRIVACY

Mask an area you want to hide on the screen with sub menu, MASK NO, MASK ACTIVE, MASK COLOR, WIDTH, HEIGHT, MOVE HOR, MOVE VER, TRANS, RESET

ADDRESS 0~255 Select the camera ID number.

ADDRESS DISPLAY OFF, ON Select the display of camera ID.

BAUDRATE Set the baudrate of RS-485 communicaon (2400, 4800, 9 600, 19200, 38400, 57600, 115200).
LANGUAGE You can select the menu language according to your requirements. ( ENGLISH, 简体, FRANÇAIS, DEUTSCH, ESPAÑOL, PORTUGUÊS, РУССКИЙ)
DEFECT ADJ Defecve pixels can be corrected.

VER. Display the firmware version.

RESET Re

set the camera sengs to the factory defaults.

EXIT Exit the setup.

WB

CONTROL

EXT

IMAGE

CONTROL

DISPLAY

CONTROL

AE

CONTROL

(EXPOSURE)

FOCUS MODE

FOCUS

CONTROL

WDR/BLC

ECLIPSE

BACK LIGHT

AUTO