Marq FOG 400 LED User Manual
User Guide
English (3–6)
Guía del usuario
Español (7–10)
Guide d’utilisation
Français (11–14)
Guida per l’uso
Italiano (15–18)
Benutzerhandbuch
Deutsch (19–22)
Appendix
English (23)
2
3
User Guide (English)
Introduction
Box Contents
Fog 400 LED User Guide
Power Cable Safety & Warranty Manual
Remote Control (wired)
Support
For the latest information about this product (documentation, technical specifications, system
requirements, compatibility information, etc.) and product registration, visit marqlighting.com.
For additional product support, visit marqlighting.com/support.
Safety Notes
Important: In addition to the notes throughout this manual, please refer to the included safety &
warranty manual for additional safety information.
• Carry this product by the handles only. Do not shake it.
• Use this product indoors only. To prevent risk of fire or shock, do not expose this product to rain
or direct and excessive moisture.
• If the environment is significantly colder than the temperature of this product, you may need to
wait for it to adjust to the ambient temperature when you power it on.
• Do not use this product for permanent installations.
• Connect this product to grounded and protected circuits only.
• Always disconnect it from its power source before cleaning it or replacing the fuse. Replace the
fuse with another of the same type and rating.
• Do not clean it with solvents or harsh detergents. Use a soft, clean cloth.
• Before connecting the product to a power source, make sure the power cable is not crimped or
damaged.
• Make sure the power outlet’s voltage is within the range stated on this product (on its housing or
decal).
• Never disconnect this product from the power cable by pulling or tugging on the cable itself.
• Always make sure this product is used in a location with adequate ventilation with at least 20”
(50cm) from adjacent surfaces. Make sure none of this product’s ventilation slots are obstructed.
• Do not use this product at ambient temperatures higher than 104 °F / 40 °C.
• Do not allow flammable materials near this product during use.
• Do not touch this product while it is powered on or immediately after powering it off. The product
and its housing can reach high temperatures.
• If you encounter a serious problem while using this product, stop using it immediately.
• Do not open this product’s housing. It contains no user-serviceable parts and will void your
warranty.
4
Features
Rear Panel
1. Cap: Twist this cap clockwise to tighten it or
counterclockwise to loosen it. The tube that passes
through its center feeds the fluid in the tank to the heater.
2. Fluid Level Indicator: This transparent part of the tank
shows its current level of fluid. If this approaches the Low
reading, fill the tank with the recommended water-based
fog fluid.
3. Power Cord: Connect this attached power cord to a
power outlet.
4. Fuse: If the fuse is broken, disconnect the power cord
from the power outlet, and then unscrew this holder to
replace the fuse. Replace it with a fuse with an appropriate
rating (printed under on the rear panel). Using a fuse with
an incorrect rating can damage the product and/or fuse.
5. Power Switch: Use this switch to power Fog 400 LED on
or off. After powering it on, wait for 2–3 minutes until the
heater is warmed up and the Ready light on the remote
control illuminates.
6. Remote Control Input: Connect the remote control to this
input.
Remote Control
1. Fog Switch: Use this switch to start or stop the production
of fog.
2. Ready Light: This light will illuminate when Fog 400 LED is
warmed up and ready to use.
1
2
3
4
5
6
1
2
5
Operation
Fluid
We recommend using high-quality water-based fog fluid with Fog 400 LED. You can purchase this
from a local or online retailer.
Important:
• Using non-water-based fluids with this product will void its warranty.
• Do not use flammable liquids such as oil, gas, perfume, etc. with this product.
• Do not ingest any of the fluids used in this product. If you do so accidentally, contact a medical
professional immediately. Rinse your eyes and skin thoroughly if they come into contact with the
fluid.
Setup
Additional Safety Notes:
• Do not spray the fog directly toward people or into an open flame.
• Keep Fog 400 LED at least 3 feet (1 meter) away from other objects, and keep it at least 10 feet
(3 meters) away from flammable materials. The nozzle becomes very hot during operation, and
the machinery requires good ventilation.
• Never touch the nozzle during operation. It becomes very hot; touching it during operation could
result in burns or other injuries.
• Use in well ventilated environment to prevent excessive concentration of vapor.
• Do not use this product as a space heater or humidifier.
Any item not listed in Introduction > Box Contents is sold separately.
1. After unpacking the box, unscrew and remove the cap at the top of the tank.
2. Fill the tank with a water-based fog fluid (described above).
3. Screw the cap back onto the top of the tank so it is secure. Make sure the tube (that passes
through the cap) is inserted as far into the tank as possible.
4. Connect Fog 400 LED to a power outlet.
5. On the rear panel, set the Power Switch to the On position. Fog 400 LED will begin warming up.
Important: If the environment is significantly colder than the temperature of Fog 400 LED, you
may need to wait for it to adjust to the ambient temperature.
6
Usage
On the remote control, the Ready Light will illuminate when Fog 400 LED reaches its normal operating
temperature. When that happens, set the Fog Switch to the On position. Fog 400 LED will start.
If the light on the remote control turns off during operation, this means the pump has stopped
because Fog 400 LED is re-heating. The light will turn on again once it is ready to use.
Throughout operation, make sure there is enough fluid in the tank. Using Fog 400 LED without any
fluid can damage it.
If Fog 400 LED is emitting an unusually low amount of fog or making an unusual noise, power it off
immediately. Make sure that the tank has enough fluid and that the fuse is not damaged.
When you are done using Fog 400 LED, power Fog 400 LED off, and wait for about 1 minute for it to
cool down.
Important: Depending on the amount of fog generated, this product may set off smoke detectors. In
certain environments after prolonged use, the fog produced may leave a slippery residue on floors
and other surfaces.
Cleaning
We recommend cleaning it after each use to prevent eventual build-up or blockages, which can
result in poor performance, overheating, and damage.
After each use, power Fog 400 LED off, and wait for about 1 minute for it to cool down. Wipe its
surfaces and empty tank using a soft, clean cloth.
After every 40 hours of use, use Fog 400 LED as described above (in Setup and Usage), but use a
mixture of 80% distilled water and 20% vinegar instead of the normal fluid. This will help remove
build-up in the nozzle.
Important: Do not clean Fog 400 LED using solvents or harsh detergents.
7
Guía del usuario (Español)
Introducción
Contenido de la caja
Fog 400 LED Guía de usuario
Cable de corriente Manual de seguridad y garantía
Control remoto (con cable)
Soporte
Para obtener la información más reciente acerca de este producto (documentación, especificaciones
técnicas, requisitos de sistema, información de compatibilidad, etc.) y registrarlo, visite
marqlighting.com.
Para obtener soporte adicional del producto, visite marqlighting.com/support.
Notas sobre la seguridad
Importante: Además de las notas a lo largo de este manual, consulte el manual de seguridad y
garantía incluido para obtener información de seguridad adicional.
• Transporte este producto sujetándolo únicamente de las manijas. No lo sacuda.
• Use este producto solo en interiores. Para evitar el riesgo de incendio o choque eléctrico, no
exponga este producto a la lluvia o a la humedad directa y excesiva.
• Si el ambiente está significativamente más frío que la temperatura de este producto, puede que
sea necesario esperar hasta que se adapte a la temperatura ambiente cuando lo encienda.
• No use este producto para instalaciones permanentes.
• Conecte este producto solo a circuitos protegidos y con descarga a tierra.
• Siempre desconecte el producto de su fuente de corriente antes de limpiarlo o reemplazar su
fusible. Remplace el fusible con otro del mismo tipo y capacidad.
• No lo limpie con solventes o detergentes agresivos. Utilice un paño suave y blando.
• Antes de conectar el producto a una fuente de corriente, asegúrese de que el cable de corriente
no esté pinzado ni dañado.
• Asegúrese de que el voltaje de la toma de corriente se encuentre dentro del rango indicado en
este producto (en su carcasa o etiqueta).
• Nunca desconecte este producto tirando de su cable de corriente.
• Asegúrese de que este producto se use siempre en una ubicación con ventilación adecuada y al
menos 50 cm (20 pulg.) de distancia de superficies adyacentes. Asegúrese de que ninguna de
las ranuras de ventilación de este producto queden obstruidas.
• No use este producto a temperaturas ambientes superiores a 104 °F / 40 °C.
• No acerque materiales inflamables a este producto durante su uso.
• No toque este producto mientras esté encendido o inmediatamente después de apagarlo. Este
producto y su carcasa pueden alcanzar temperaturas elevadas.
• Si se encuentra con un problema grave al usar este producto, deje de usarlo inmediatamente.
• No abra la carcasa de este producto. No contiene piezas reparables por el usuario y hacerlo
invalidará la garantía.
8
Características
Panel trasero
1. Tapa: Gire la tapa en sentido horario para apretarla o en
sentido antihorario para aflojarla. El tubo que atraviesa su
centro transporta el líquido en el tanque hacia el
calentador.
2. Indicador de nivel de líquido: Esta parte transparente del
tanque muestra su nivel actual de líquido. Si el nivel se
acerca a la marca Low (Insuficiente) llene el tanque con el
líquido para máquinas de humo a base de agua
recomendado.
3. Cable de alimentación: Conecte este cable de corriente
incorporado a una toma de corriente.
4. Fusible: Si el fusible está roto, desconecte el cable de
alimentación de la toma de corriente y desatornille este
soporte para reemplazar el fusible. Reemplácelo por un
fusible de la especificación apropiada (impresa en o debajo
del portafusibles). Si utiliza un fusible de especificación
incorrecta, puede dañarse la unidad y/o el fusible.
5. Interruptor de encendido: Utilice este interruptor para
encender y apagar el Fog 400 LED. Luego de encenderlo,
espere de 2 a 3 minutos hasta que el calentador alcance la
temperatura y se encienda la luz Ready (Listo) en el
control remoto.
6. Entrada del control remoto: Conecte a esta entrada el
control remoto incluido.
Control remoto
1. Interruptor de humo: Utilice este interruptor para iniciar o
detener la generación de humo.
2. Luz de humo listo: Esta luz se encenderá cuando el Fog
400 LED haya alcanzado la temperatura de funcionamiento
y esté listo para utilizarse.
1
2
3
4
5
6
1
2
Loading...