Marley Engineered Products Radiant Heater User Manual
Radiant Heater
Desk Heater: 200 Series
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
CAUTION - TO REDUCE RISK OF FIRE AND
ELECTRIC SHOCK:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid bums, do
not let bare skin touch hot surfaces. Do not partially or fully cover or obstruct the front of this heater.
3. Extreme caution is necessary when any heater is
used by, or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug, or after the heater malfunctions, or has been
dropped or damaged in any manner. Return heater
to the factory as outlined in the warranty for all
repairs.
6. Do not use outdoors.
7. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, etc. Arrange cord away
from traffic area and where it will not be tripped
over.
8. This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never
locate heater where it may fall into a bathtub or
other water container. Do not turn heater on or off
when standing in water or if your hands are in
water. Disregard of this warning may result in fatal
accident.
9. To disconnect heater , turn switch of f, then remove plug
from outlet.
10.Connect to properly grounded polarized outlets
only.
11. Do not make holes of any kind in the heater. If you
do, you can damage this heater and void this warranty.
12.To prevent a possible fire, do not use this heater on
soft surfaces, like a bed. Do not leave heater
turned on when face down or when front of the
heater is covered in any way with any material.
13.A heater has hot and arcing or sparking parts
inside. Do not use it in areas where gasoline, paint
or flammable liquids are used or stored.
14. Use this heater only as described in this manual.
Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
15. Avoid the use of an extension cord, because the
extension cord may overheat and cause a risk of
fire.
16.If an extension cord must be used, the cord shall be
No. 18AWG and rated not less than 600 watts.
Installation & Maintenance Instructions
SAVE THESE INSTRUCTIONS
WARNING
!
E152700
7/03
Part No. 5200-2184-003
ECR35841
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except heating elements which are warranted against defects in workmanship and materials for five years from date of installation. This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained in
violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred to return products to
Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service center or
the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that such
repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR APARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED FROM THIS
AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARISING WITH RESPECT TO THE PRODUCT,
WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When requesting return authorization,
include all catalog numbers shown on the products.
GENERAL
200 Series radiant heaters are designed to provide supplemental heat in small areas such as offices and may be
used as an under desk heater. However, care must be
taken to avoid blocking heater or covering it with any thing
that could allow it to build up heat – See warnings.
INSTALLATION INSTRUCTIONS
This heater operates in vertical position only. For mounting
heater to desk, apply velcro to top of heater back, one
piece near each comer. Remove backing from back of velcro and press firmly against the desired position on the
desk. Normal position is vertical against the desk kneewell panel with the top of the heater at knee height. To
remove, pull bottom of heater firmly away from desk.
Heater can be restored to original position by once again
attaching to velcro. the leg on the back swings out to support the heater when used as a portable heater.
INSTRUCTIONS FOR USE AND CARE
Heaters are provided with flexible cord with a polarized 2
blade plug (as shown in Figure 1) and built-in ON/OFF
switch.
This heater is for use at l20 volt AC only.
Heaters may be cleaned using a damp cloth or sponge
and a mild detergent. Never submerge or soak heater in
water
. Heaters may be repainted if desired. Use only high
temperature water based acrylic paints.
Always unplug heaters when not in use. When heaters are
not to be used for an extended period of time, cord should
be coiled and tied to prevent damage and heater should
be stored in a safe location.
If heater fails to operate or if heater or power cord
becomes damaged, unplug and discontinue use.
DO NOT
attempt to repair the heater. If the heater fails during the
warranty period, return to place of purchase or to the factory as outlined in the
LIMITED WARRANTY STATEMENT
below.
Occasionally a new heater will emit a slight “new smell”
odor during initial use. This smell should dissipate within
the first hour of use.
Figure 1
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
HOW TO OBTAIN WARRANTY SERVICE AND
WARRANTY PARTS PLUS GENERAL INFORMATION
1. Warranty Service or Parts 1-800-642-4328
2. Purchase Replacement Parts 1-800-654-3545
3. General Product Information www.marleymep.com
Note: When obtaining service always have the following:
1. Model number of the product
2. Date of manufacture
3. Part number or description
Loading...