Marley Engineered Products 562A User Manual

WARNING

MODEL NO. 402A,

482A & 562A

Portable Unit Heaters

Dear Owner,

Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley
Engineered Products. You have made a wise investment selecting the highest quality product in the heat­ing industry. Please carefully read and follow the installation and maintenance directions shown in this
manual. You should enjoy years of efficient heating comfort with this product from Marley Engineered
Products... the industry’s leader in design, manufacturing, quality and service.

... The Employees of
Marley Engineered Products

Installation & Maintenance Instructions

!

1

Read Carefully - These instructions contain vital infor-

mation for the proper installation, use and efficient opera­tion of the heater. Carefully read these instructions before
installation, operation, or cleaning of the heater. Failure to
adhere to the instructions could result in fire, electric
shock, serious personal injury, death or property damage.
Save these instructions and review frequently for continu­ing safe operation and instruction of future users.

1. Connect to properly grounded outlets only.

2. Check heater voltage and amperage on back of heater to
make sure it agrees with the electric service supplied.

3. Ground fault circuit protection is required if heater is used in
damp areas such as basements or garages. This heater is
not suitable for use in wet or very humid locations.

4. Do not use outdoors.

5. Never locate heater where it may fall into a bathtub or other
water container.

6. Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock, fire,
or damage the heater.

7. To prevent a possible fire, do not block air intakes or exhaust
in any manner. Do not use on soft surfaces, like a bed,
where openings may become blocked. Clean as often as

necessary to prevent dust from clogging the grilles or ele­ment fins. Keep all electrical cords, drapes, paper, plastics
and other combustibles away from heater.

8. Do not run cord under carpeting. Do not cover cord with
throw rugs, runners, etc. T o prevent entanglement or damage,
route cord away from high traffic areas.

9. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids are
used or stored

10. If this heater or its power cord become damaged or malfunc­tion in any way, unplug heater, discontinue use, and have
unit repaired by a reputable repair service.

11. Heater is hot when in use. To avoid burns do not let bare skin
touch hot surfaces. Use handle to move heater.

12. Do not use an extension cord with this heater. Do not cut off
plug and wire heater directly.

13. Extreme caution is necessary when heater is used by or near
children or invalids and whenever heater is left operating
unattended

402A

482A & 562A

File #E152700

PLUG TYPE
20 amp 240 V
NEMA #6-20P

PLUG TYPE
30 amp 240 V
NEMA #6-30P

SA VE THESE INSTR UCTIONS

GENERAL

Prior to operating heater, make sure the electrical outlet is of the
configuration and capacity appropriate for the heater. See outlet
configuration on front page of manual. No adapter is available for
this blade configuration and none should be used. The outlet pro­vided must be a 240 volts grounded type. When properly
installed, it provides a ground connection through the cord of the
heater to protect the operator from electric shock. In workshops,
locate heater away from sources of wood dust.

FLOOR APPLICATION

The heater is for floor mounting. Place the heater on floor or
other flat surface and insert plug into the proper wall outlet.

HEATER OPERATION

Set thermostat to its full counterclockwise position. Plug the unit
into a properly grounded 240 V outlet. (#6-20 for model 402A, #6­30 for models 482A & 562A). Set the thermostat to the farthest
clockwise position. The fan should come on and the unit will start
heating the room. When the room reaches comfort level, turn the
thermostat counterclockwise until the heater turns off. The heater
will cycle automatically around this preset temperature. To
increase temperature, turn the thermostat knob clockwise. To
lower temperature, turn the thermostat counterclockwise.

CONTINUOUS FAN OPERATION

(MODEL 562A ONLY)

To activate the continuous fan feature, set rocker switch to “ON”
position. The elements will continue to cycle on the thermostat set­ting. For no heat, turn thermostat to full counterclockwise position.
With fan in “AUTO” position, fan will cycle with the thermostat.

CLEANING AND STORAGE

Turn thermostat off and remove plug from electrical outlet before
cleaning heater. Use a soft cloth for dusting. For cleaning, use only
a damp rag and non-abrasive dish detergent. Do not use abrasive
chemical cleaners as these may harm the finish.
If heater is used in very dusty location, use a vacuum cleaner dust
brush to remove dust and other foreign material from the grilles.
Always unplug cord and wrap around heater handle when not in
use. Move heater to a safe location for storage.

SERVICE

This heater does not require any routine maintenance other than
occasional cleaning to prevent clogging of intake grille opening. To
clean air intake grille, use vacuum with brush attachment or high
pressure air. The motor is permanently lubricated. Do not operate
the heater with a damaged cord or plug or if the heater malfunctions
or has been damaged in any manner. Return heater to authorized
service facility for examination, electrical, or mechanical adjust­ment, or repair. Call the toll free number listed for assistance in
locating the Marley authorized service center in your area.

WARNING

!

BE CAREFUL NOT TO DIRECT THE AIRSTREAM AT
DRAPERIES, FURNITURE, OR OTHER OBJECTS THAT
COULD BE DAMAGED BY HEAT.

DO NOT PLACE THE
HEATER WHERE A SMALL CHILD MAY FALL OVER THE
HEATER.

DO NOT PLACE THE HEATER WHERE THE POWER
CORD MAY BE WALKED ON, TRIPPED OVER, OR OTHER­WISE SUBJECTED TO HARD USAGE.

MODEL

AMPS

DATE

VOLTS

PH Hz

482A WK/YY

240/208

1

60

20.0/17.3

NAMEPLATE

5200-2274-003 ECR35081 12/01

How to order repair parts:
In order to obtain any needed repair or replacement parts, war­ranty service or technical information, please contact the Marley
Engineered Products Service Center toll-free by calling 1-800­642-HEAT.
When ordering replacement parts, always give the information
listed as follows:

1. The Part Number

2. The Model Number

3. The Part Description

4. Date of Manufacture

WARNING

!

OPERATION OF THE SAFETY THERMALLIMITCONTROLINDI­CATES THE HEA TER HAS BEEN SUBJECTED TO SOME ABNOR­MAL CONDITIONS. IT IS RECOMMENDED THATTHE HEA TER
BE CHECKED BY A REPUTABLE ELECTRICIAN OR REPAIR SER­VICE TO INSURE THE HEATER HAS NOT BEEN DAMAGED.

MADE IN TAIWAN FOR:

2

LIMITED WARRANTY

All products manufactured by Marley Engineered Products are
warranted against defects in workmanship and materials for one
year from date of installation, except heating elements which are
warranted against defects in workmanship and materials for five
years from date of installation. This warranty does not apply to
damage from accident, misuse, or alteration; nor where the con­nected voltage is more than 5% above the nameplate voltage; nor
to equipment improperly installed or wired or maintained in viola­tion of the product’s installation instructions. All claims for war­ranty work must be accompanied by proof of the date of installa­tion.

The customer shall be responsible for all costs incurred in the
removal or reinstallation of products, including labor costs, and
shipping costs incurred to return products to Marley Engineered
Products Service Center. Within the limitations of this warranty,
inoperative units should be returned to the nearest Marley autho­rized service center or the Marley Engineered Products Service
Center, and we will repair or replace, at our option, at no charge
to you with return freight paid by Marley. It is agreed that such
repair or replacement is the exclusive remedy available from
Marley Engineered Products.

THE ABOVE WARRANTIES ARE IN LIEU OF ALLOTHER WAR­RANTIES EXPRESSED OR IMPLIED. AND ALL IMPLIED WAR­RANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR­TICULAR PURPOSE WHICH EXCEED THE AFORESAID
EXPRESSED WARRANTIES ARE HEREBY DISCLAIMED AND
EXCLUDED FROM THIS AGREEMENT. MARLEY ENGI­NEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSE­QUENTIAL DAMAGES ARISING WITH RESPECT TO THE
PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT,
STRICT LIABILITY, OR CONTRACT.

Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above exclusion or limitation
may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state
to state.

For the address of your nearest authorized service center, con­tact Marley Engineered Products in Bennettsville, SC, at 1-800­642-4328. Merchandise returned to the factory must be accom­panied by a return authorization and service identification tag,
both available from Marley Engineered Products. When request­ing return authorization, include all catalog numbers shown on
the products.

2F68

MAX.

MIN.

SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA