Marksman 67063c, 67071c Instruction Manual
INSTRUCTION MANUAL
Read all the instruction carefully before you use
the appliance and keep it for future use.
600W ANGLE GRINDER
230V~50Hz
600W 11000RPM
115MM DISC
3 AMP fuse (max) must be fitted to
plug attached to this cable.
67063c
67071c
IMPORTANT SAFEGUARDS
Please read these operating instructions before using the tool for the first time and keep them with
the tool at all times.
Overview
1. On And Off Switch
2. Drive Shaft
3. Side Handle
4. Gear Box
5. Housing Handle
6. Protective Cover
7. Lock Button
8. External Flange Spanner
9. External Flange with Thread
10. Internal Flange
Technical Data 67063c - 67071c
Voltage/Frequency: 230V- 50Hz
Input power: 600w
No-load speed: 11000/min
Disc size: Ø115mm
-1
General Safety Instructions for Electric Tools
This device is to be exclusively for private use! It is not fit for commercial use!
Warning: when working with electrical devices the following prevention and safety
instructions are to be observed to avoid fires, electric shocks an physical injuries!
For safe working:
• Keep the working area in order’
• Disorder in the working area can give rise to dangers of accidents! Pay attention to the ambient
conditions!
• Do not leave electric tools under the rain!
• Do not use these in humid or wet surroundings! .
• Make sure that there is enough light! Make sure that the working area is visible at a glance!
• Do not use electric tools in areas subject to the risk of res! Protect yourself against electric
shocks!
• Avoid coming into contact with earth parts (e.g. pipes, radiators. stoves, refrigerators) !
• In case of extreme application conditions (e.g. high humidity, presence of metal particles, etc.) the
electrical safety of the device can be improved by connecting an isolation transformer or a fault
current circuit breaker!
• Keep children away!
• Do not let other people touch the tool or the cable!
• Keep other people out of the working area! Make sure that the tool is stored . safely!
• Unused electric tools are to be kept in a dry, secure place, out of the reach of children!
• Do not overload the electric tool! It works better and safer within the indicated capacity range! Use
the right electric tool!
• Do not use weak tools or adapters for heavy jobs. Do not use tools for purposes or jobs for which
these are not intended. For example. hand circular saws are not be used to cut trees or branches!
Always wear suitable working cloths!
• Do not wear baggy cloths or jewellery! Risk of being caught by moving parts!
• When working outside. it is advisable to wear rubber gloves and skid-proof shoes!
• If you have long hair, wear a hairnet! Use protective goggles!
• Always wear a breathing mask during jobs producing dust! Connect the vacuum system
(if available).
• If devices for the connection of vacuum and collection systems are available,” make sure that
these are connected and used correctly!
• Do not tamper with the cable!
• Do not carry the tool by the cable and do not use it to pull the plug out of the socket!
• Protect the cable against heat sources, oil and sharp edges! Secure the tool!
• Use chucking devices or a vise to keep the tool still! The tool can thus be held in place more safely
than by hand and the tool can be used with both hands!
• Avoid unusual body postures! Always stand rmly in place and keep your balance! Always keep
the tool in good order!
• Always keep tools sharp and clean to work correctly and safely!
• Follow the maintenance and tool change instructions!
• Check the plug and cable on a regular basis and have a qualied technician change these
in case of damage!
• Check the extension cable on a regular basis and replace it if damaged!
• Remove the plug out from the socket! After use, before maintenance and when changing
accessories such as saw blades, drills cutters, etc.! Do not leave protruding tool keys!
• Make sure before turning on the tool that the key or setting gauge is removed!
• Avoid the accidental starting of the tool!
• Never carry an electric tool connected to the power mains with your nger on the switch!
• Make sure that the switch is off when connecting to the mains! If using extension cable outdoors:
Use only certied and duly marked extension cables outdoors!
• Always be careful! Pay attention to your work! Proceed carefully. Do not use the tool if you
are not concentrated!
• Check the tool for damages!
• Before using the tool the next time check that the protection devices or slightly damaged parts are
in good working conditions! Check whether the moving parts function correctly, that these are not
jammed or whether any parts are damaged!
• All the parts to be correctly mounted and meet all the requirements for the proper functioning of
the electric tool!
• Damaged protection devices and parts are to be repaired or changed by a qualied technician
provided that the operating instructions do not specify otherwise!
Loading...