Page 1
ONE 6-GALLON TILTING
G
MODEL: m MT6G100A m MT6G200A
SIZE: 24" Wide x 33" Front-to-Back
(610mm Wide x 838mm Front-to-Back)
DESCRIPTION:
Will be a Market Forge Model ___________, tilting steam
jacketed trunnion kettle. Kettle will be mounted on a 28"
(711mm) high cabinet base. Hot and cold water fill faucet,
depressed area, drains, and steam control valves will be
located on stainless steel marine-edged countertop. A 4"
(102 mm) deep 12" x 10" (305 mm x 254 mm) clean-up pan
with removable splash guard will be standard. (Splash
guard will be removable so that it may also be attached to a
food receiving pan.) Kettles are made from #316 stainless
steel and will be A.S.M.E.- approved and National Board
Registered.
Cabinet base, constructed of stainless steel frame, which
houses the gas fired boiler, will be of modular design to
match other Market Forge cooking equipment. Base with
stainless steel frame will be equipped with 6" (152 mm)
stainless steel legs and adjustable bullet feet, reinforced
die-formed stainless steel marine-edged countertop, and
hinged doors with magnetic latches. Unit will be polished
stainless steel.
KETTLE MOUNTED ON
GAS STEAM GENERATOR
JOB NAME: __________________________
ITEM NO.: ___________________________
NO. REQUIRED: ______________________
Manifold and pilot gas pressure will be 4" (102mm) for
Natural Gas and 10" (254mm) for LP Gas. Incoming gas
pressure must not exceed 14" (357mm) W.C.
Steam generator will be automatically filled with hot water
and brought t 15 PSI (1.0kg/cm
water switches are turned on and automatically drained
under pressure when switches are turned off. Cold water
condenser will automatically condense exhaust steam into
water before releaseing it to drain.
2
) pressure when heat and
Spec No. S-2363B
08/04
COOKING CAPACITY:
m MT6G - 6 Gallon (23 liter)
OPERATION WILL BE BY:
Electrically Operated at 15PSI (1.0kg/cm2), built in
accordance with A.S.M.A Codes, equipped for operation
with:
m 100,000 BTU m 200,000 BTU
Boiler will be equipped for:
m Natural Gas m LP Gas
The manufacturer reserves the right to modify materials and specifications without notice
Printed in U.S.A.
Tel: (617) 387-4100 l Fax: 1-800-227-2659 (Ex. MA) l (617) 387-4456 (MA and Overseas)
STANDARD FEATURES:
m Safety Valve.
m Low Water Cut-Of
m Water Strainer
m Access Point for T
OPTIONAL AT EXTRA COST:
m One-piece Lift-off Stainless Steel Cover.
m Clean-up brush.
m Stainless Steel Wire Basket.
m 200,000 BTU.
f.
.
otal Concept and P.M. Plus.
An Employee Owned Company
35 Garvey Street l Everett l MA l 02149
E-Mail: CUSTSERV@mfii.com l Website: www.mfii.com
FOOD SERVICE EQUIPMENT
6 Gallon Tilting Kettle
Page 2
G
ONE 6-GALLON TILTING
KETTLE MOUNTED ON
GAS STEAM GENERATOR
Gas Operated
Gas Connection - 3/4" (19mm) NPT female.
G
HW
Hot Water — 3/8" (9.5mm) N.P.T. female for hot
water to kettle fill faucet. Max. 50 PSI (3.5kg/cm
and min. 25 PSI (1.8kg/cm
Cold Water — 3/8" (9.5mm) N.P.T. female for cold
CW
water to kettle fill faucet. Max. 50 PSI (3.5kg/cm
and min. 25 PSI (1.8kg/cm
Drain — Pipe full 2" (50mm) N.P.T. female to flush
D
floor drain. Do not make solid connection to floor
drain.
Electrical Connection - 115 VAC, 60Hz, 2 Amps, 1/2"
EC
(13mm) conduit connection or equivalent. Use wire
suitable for at least 90
DETAILS & DIMENSION
SERVICE CONNECTIONS
2
) water pressure.
2
) water pressure.
o
C.
2
)
2
)
Steam Take-Off — 3/4" (19mm) N.P.T. female for
ST*
incoming steam from Market Forge boiler.
Spec No. S-2363B
08/04
* Steam supply connection available on either side of
cabinet base.
CAUTION:
Before connecting water to this unit, water supply should
be analyzed
grains per gallon and pH level is within the range of 7.0-8.5.
Water that fails to meet these standards should be treated
by installation of water conditioner. EQUIPMENT FAILURE
CAUSED BY INADEQUATE WATER QUALITY IS NOT
COVERED UNDER WARRANTY.
NOTES:
Units supplied for use in Canada require only one
electrical connection at "EP" for both power and control
circuits.
PVC and CPVC pipe are not acceptable materials for
drains.
to make sure hardness is no greater than 2.0
6 Gallon Tilting Kettle
It is our policy to build equipment which is design certified by A.G.A., U.L., A.S.M.E., N.S.F., C.G.A. and C.S.A. However, a continuing program of product
improvement makes it necessary to submit new models to the agencies as they are developed and consequently not all models bear the appropriate agency labels
FOOD SERVICE EQUIPMENT
Printed in U.S.A.
An Employee Owned Company
35 Garvey Street l Everett l MA l 02149
Tel: (617) 387-4100 l Fax: 1-800-227-2659 (Ex. MA) l (617) 387-4456 (MA and Overseas)
E-Mail: CUSTSERV@mfii.com l Website: www.mfii.com
Loading...