Market Forge MT6G User Manual
6 OR 10 GALLON TILTING KETTLE
G
MODELS
MT6G - six gallon (23 liter) gas tilting kettle
MT10G - ten gallon (38 liter) gas tilting kettle
DESCRIPTION
Will be a Market Forge Model ___________, tilting steam jacketed
trunnion kettle. Kettle will be mounted on a 28” (711mm) high cabinet base. Hot and cold water fill faucet, depressed area, drains, and
steam control valves will be located on stainless steel marine-edged
countertop. A 4” (102mm) deep 12” x 10” (305 mm x 254 mm)
clean-up pan with removable splash guard will be standard. Splash
guard will be removable so that it may also be attached to a food
receiving pan. Kettles are made from #316 stainless steel and will
be A.S.M.E.- approved and National Board Registered.
Cabinet base, constructed of stainless steel frame, which houses
the gas fired boiler, will be of modular design to match other Market
Forge cooking equipment. Base with stainless steel frame will be
equipped with 6” (152mm) stainless steel legs and adjustable bullet
feet, reinforced die-formed stainless steel marine-edged countertop,
and stainless steel lift -off front cover. Unit will be polished stainless
steel.
The CSD-1 compliant steam boiler features an intermittent spark
pilot ignition and nickel plating. The steam boiler will be automati-
Gas Tilting Kettle
cally filled with water and brought to pressure when water and heat
switches are turned on and automatically drained under pressure
when water and heat switches are turned off. A cold water condenser will automatically condense all exhausted steam before it is
FOOD SERVICE EQUIPMENT
released from the cooker and steam boiler drain. Also includes an
ASSE approved backflow preventer, automatic water level control,
low water cut-off, water strainer and cathodic protector. For more
boiler information see the M24G-M36G spec sheet (14-0111).
OPERATION WILL BE BY
Electrically Operated at 15PSI (1.0kg/cm²), built in accordance with
A.S.M.A Codes, equipped for operation with 200,000 BTU option
Boiler will be equipped for:
Natural Gas
LP Gas
Boiler shall be operated at a MAWP of 15 PSI (1kg/cm2)
Manifold gas pressure shall be 4” W.C. (102mm) for natural gas and
10” W.C. (254mm) for LP Gas. Incoming pressure must not exceed
14” W.C. (357mm).
ON A GAS STEAM BOILER
JOB NAME: ___________________________
ITEM NO.: ____________________________
NO. REQUIRED: _______________________
MT10G Shown
OPTIONS & ACCESSORIES
(at additional charge)
Cleaning Accessories
28” long kettle draw-off brush
36” long clean up brush
8-1/2” long clean up brush
48” long kettle paddle
48” long kettle whip
Clean up pan
Tilting kettle accessory kit, includes draw-off brush,
36” clean up brush, 8-1/2” clean up brush, whip, solid
strainer and pan holder
One piece lift-off stainless steel cover
Stainless steel wire basket
Prison package, includes lockable stainless steel covers,
tamper proof screws, (4) 6” adjustable flanged feet
6” Flanged Feet
Filter System
60” water hose with quick disconnect
SHIPPING WEIGHT
MT6G - 470 lbs (213 kg)
MT10G - 500 lbs (227 kg)
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
www.mfii.com
G
6 OR 10 GALLON TILTING KETTLE
ON A GAS STEAM BOILER
DETAILS & DIMENSIONS
SERVICE CONNECTIONS
G Gas Connection - 3/4” (19mm) NPT female
CW1 Cold Water - 3/8” (10mm) NPT for cold water to boiler. Cold
water lines will have a maximum of 50 PSI (3.5kg/ cw2) and a
minimum of 25 PSI (1.8 kg/cw2) water pressure
CW2 Cold Water - 3/8” (10mm) NPT for cold water to condenser
and kettle fill faucet. Cold water lines will have a maximum of
50 PSI (3.5kg/cw2) and a minimum of 25 PSI (1.8 kg/cw2)
water pressure.
HW Hot Water - 3/8” (10mm) NPT female for hot water to kettle fill
faucet. Hot water line will have a maximum of 50 PSI (3.5kg/
cw2) and a minimum of 25 PSI (1.8 kg/cw2) water pressure.
D Drain — Pipe full 2” (50mm) N.P.T. female to flush floor drain.
Do not make solid connection to floor drain
EC Electrical Connection - 120 Volts AC, 60 Hz, single phase,
and a 9 foot Power Cord/NEMA 5-15.
ST Steam Take-Off — 3/4” (19mm) N.P.T. female for incoming
steam from Market Forge boiler
OPERATION WILL BE BY
Gas fired, A.S.M.E. constructed and National Board Registered, 15 PSI
(1 kg/cm2) steam boiler rated at 200,000 BTU
Notes: If equipment is installed where elevation exceeds 2,000 feet
(609.6 meters) above sea level, specify installation altitude so that proper
Gas Tilting Kettle
gas orifices can be provided.
The only available space to supply utilities to the gas boiler is the 6”
(152mm) space between the floor and the cabinet.
FOOD SERVICE EQUIPMENT
Allow 3” (76mm) space from side wall and 6” (152mm) from rear wall if
adjoining walls are combustible.
PVC & CPVC PIPE ARE NOT ACCEPTABLE MATERIALS FOR
DRAINS.
CAUTION: REMOTE KETTLE OPERATION If this boiler is feeding a
remote kettle that will be more than 5 feet (1.5 meters) away, consult
factory before ordering.
DIMENSIONS ARE IN INCHES [MM]
4[102]
2.5 [64]
D
CW1
CW2
HW
12.5
[318
58 [1473]
MT10G
55.25
[1403]
MT6G
10.5
[267]
22
[559]
8.5
[216]
3 [76]
EC
5 [127]
24 [610]
EC
FLUE
ST
ST
5 [127]
10.5
[267]
33
[838]
2.75 [70]
G
28
[711]
WATER SUPPLY
Good quality water feed is the responsibility of the owner. Water quality
must be within the following general guidelines.
TDS: 40-125 ppm Hardness: 35-100 ppm Chlorine: <0.2 ppm
Silica: <13 ppm Chlorides: <25 ppm
Chloramine: <0.2 ppm pH: 7.0 - 8.5
The best defense against poor water quality is a water treatment system
designed to meet your water quality conditions.
The manufacturer reserves the right to modify materials and specifications without notice.
PRINTED IN U. S. A.
SPEC SHEET: 14-0122 Rev D (4/16)
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
8 [203]
CW3
CW2
CW1
D
G
6 [152]
www.mfii.com
Loading...