Market Forge MT-25EO User Manual

25 & 40 GALLON STEAM JACKETED

E

MODELS

 MT-25EO - 25 gallon (95 liter), modular base, electric, tilting kettle
 MT-40EO - 40 gallon (152 liter), modular base, electric, tilting

kettle

DESCRIPTION

Shall be a Market Forge Model MT-25EO / MT-40EO steam jacketed
tilting kettle with self-contained electric boiler.

Kettle shall be of stainless steel mounted in an enclosed cabinet base
containing a 24 kW electrically powered steam boiler for operation of
the kettle.

Cooking temperature shall be controlled with a steam control valve
located on the right side of cabinet top. A hot and cold water fill
faucet with swing spout shall be located on cabinet top. Kettle shall
be equipped with a 2” (51mm) sanitary draw-off valve which shall be
enclosed for sanitary purposes. This valve will empty into a swing
drain which shall be removable without tools and shall be equipped
with a removable stainless steel strainer. Unit shall include a one-piece
counter-balanced stainless steel cover.

Cabinet base shall be of modular design to match other Market
Forge equipment and enclose steam boiler. Kettle base shall have
6” (152mm) stainless steel legs with hold-down feet in the rear. The
base front shall have reinforced die-formed stainless steel door with
magnetic latches.

Kettle shall tilt upright to allow complete emptying of contents under

Electric Steam Jacketed Kettle

positive control by turning the removable crank. Kettle is equipped with

FOOD SERVICE EQUIPMENT

a steam trap located on bottom of kettle. A pan support, removable
without tools, shall maintain pan in horizontal position not more than 2”
(51mm) from kettle lip throughout tilting angle. 25 & 40 Gallon kettles
come standard with 316 liner.

Pan support shall hold: one 12” x 20” x 2 1/2” deep pan (305mm x
508mm).

Steam boiler shall be nickel plated mounted independent of kettle with­in the cabinet base and allow for separate replacement of heating ele­ments. The MT-25EO and MT-40EO shall bring 20 gallons of water to
a boil, with cover down, in aproximately 35 minutes. Unit shall include
as standard: electric controls, low water cut-off, pressure gauge, air
vent, saftey relief valve, water level sight gauge, automatic cold water
steam condenser system, automatic cold water boiler fill and electric
solenoid valves for steam, drain and water. Boiler also includes and a
single ASSE approved, check valve/backflow preventer to the boiler
feed. Steam boiler shall be ASME constructed and National Board
Registered.

OPERATION SHALL BE BY:

Self-contained high speed 24 kW electric self-generating steam boiler
of the following characteristics:

 208 volt AC, 3 phase 60 Hz
 240 volt AC, 3 phase 60 Hz
 480 volt AC, 3 phase 60 Hz

ELECTRIC TILTING KETTLE

JOB NAME: ___________________________

ITEM NO.: ____________________________

NO. REQUIRED: _______________________

MT-40EO shown

SHIPPING WEIGHT

 MT-25EO - 410 lbs (186 kg)
 MT-40EO - 430 lbs (195 kg)

OPTIONS & ACCESSORIES

(at additional charge)

 Cleaning Accessories

 28” long kettle draw-off brush
 36” long clean up brush
 8-1/2” long clean up brush
 48” long kettle paddle
 48” long kettle whip
 Tilting kettle accessory kit, includes draw-off brush,

36” clean up brush, 8-1/2” clean up brush, whip, solid

strainer and pan holder
 Power tilt mechanism
 Prison package, includes lockable stainless steel covers,

tamper proof screws, (4) 6” adjustable flanged feet
 Filter System
 Flanged Feet
 60” water hose with quick disconnect (2) required.

44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: [phone] • Fax: [phone]

www.mfii.com

E

65.5 [1664] MAXIMUM HEIGHT

25 & 40 GALLON STEAM JACKETED

ELECTRIC TILTING KETTLE

DETAILS & DIMENSIONS

ELECTRICAL REQUIRMENTS

Volts Phase Amps

208 3 66.6

240 3 57.7

480 3 28.8

SERVICE CONNECTIONS

EP Power Supply - Use wire suitable for at least 90°C,

Nominal amps per line wire at 24 KW:

EC Electrical Controls - 115 Volts Ac, 60Hz, 40 watts, 1/2”

(13mm) conduit connection or equivalent. Use wire suitable
for at least 90°C. Draws less than 1 AMP with power lift.

D Drain - Pipe full 2” (51mm) NPT to floor drain. DO NOT

MAKE SOLID CONNECTION TO FLOOR DRAIN. PVC and
CPVC are not acceptable materials for drains.

HWK Hot Water - 3/8” (10mm) NPT Female for Hot Water to

Kettle Faucet (See Note 3)

CWK Cold Water - 3/8” (10mm) NPT Female for Cold Water to

Kettle Faucet (See Note 3)

CWB Cold Water - 3/8” (10mm) NPT Female for Cold Water to

Boiler. Water may be filtered (See Note 3).

CWC Cold Water - 3/8” (10mm) NPT Female for Cold Water

Condenser (See Note 3)

DIMENSIONS ARE IN INCHES [MM]

15 [381]

D

See Note 1

9 [228]

12 [305]

2.88 [73]

2.5 [64]

2.88 [73]

EC

15

[381]

36 [914]

EP

CWK

CWC

6.38

[162]

HWK

11.5
[292]

1.75 [45]

4.31 [110]

CWB

16.25 [413]

13.88 [352]

33 [838]

NOTES:

Electric Steam Jacketed Kettle

1. Recess area for kettle draw-off must be kept free of all piping and

FOOD SERVICE EQUIPMENT

connections.

2. The only available space to supply utilities to the unit is the 6”
(152mm) height between the floor and the cabinet.

3. Water pressure max 50 PSI (3.5kg/cm2) and min 25 PSI (1.8kg/
cm2).

CAUTION: REMOTE KETTLE OPERATION If this boiler is feeding a
remote kettle that will be more than 5 feet (1.5 meters) away, consult
factory before ordering.

WATER SUPPLY

Good quality water feed is the responsibility of the owner. Water quality
must be within the following general guidelines.

TDS: 40-125 ppm Hardness: 35-100 ppm Chlorine: <0.2 ppm
Silica: <13 ppm Chlorides: <25 ppm
Chloramine: <0.2 ppm pH: 7.0 - 8.5

The best defense against poor water quality is a water treatment system
designed to meet your water quality conditions.

38 [965]

21 [533]

[152]

D

The manufacturer reserves the right to modify materials

See Note 1

6

EC EP

and specifications without notice.

HWK CWK CWB

28 [711]

7

[179]

CWC

PRINTED IN U. S. A.
SPEC SHEET: 14-0121 Rev D (4/16)

44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: [phone] • Fax: [phone]

www.mfii.com