Market Forge MT10T6G User Manual
(1) 6 GALLON & (1) 10 GALLON TILTING
G
MODELS
MT10T6G - (1) six gallon (23 liter) and (1) ten gallon (38 liter)
tilting kettle on a gas steam boiler
DESCRIPTION
Market Forge Model ________ Steam Jacketed Tilting Kettles.
Kettles will be mounted on a 28” (711mm) high cabinet base. Hot and
cold water fill faucet, depressed area and drains, and steam control
valve will be located on stainless steel marine-edged counter-top.
A 4” (120mm) deep clean-up pan 12” x 10” (305mm x 254mm) with
removable splash guard will be standard. Splash guard will be removable so that it may also be attached to a food receiving pan. Kettle
made from #316 stainless steel will A.S.M.E approved and National
Board Registered.
Cabinet base, constructed of a stainless steel frame, which houses
the gas fired boiler, will be of modular design to match other Market
Forged cooking equipment. Base will be equipped with 6” (125mm)
stainless steel marine-edged countertop and and stainless steel lift
-off front cover. Units will be polished stainless steel.
The CSD-1 compliant steam boiler features an intermittent spark pilot
ignition and nickel plating. The steam boiler will be automatically filled
with water and brought to pressure when water and heat switches
are turned on and automatically drained under pressure when water
and heat switches are turned off. A cold water condenser will automatically condense all exhausted steam before it is released from
Two Gas Tilting Kettles
the cooker and steam boiler drain. Also includes an ASSE approved
backflow preventer, automatic water level control, low water cut-off,
FOOD SERVICE EQUIPMENT
water strainer and cathodic protector. For more boiler information see
the M24G-M36G spec sheet (14-0111).
OPERATION SHALL BE BY:
Gas fired, 15 PSI (1kg/cm2), A.S.M.E constructed and National Board
Registered steam boiler rated at:
200,000 BTU (standard)
300,000 BTU (Optional at Extra Cost)
Boiler will be equipped for:
Natural Gas
LP Gas
Manifold gas pressure shall be 4” W.C. (102mm) for natural gas and
10” W.C. (254mm) for LP Gas. Incoming pressure must not exceed
14” W.C. (357mm).
SHIPPING WEIGHT
625 lbs (284 kg)
KETTLES ON A GAS STEAM BOILER
JOB NAME: ___________________________
ITEM NO.: ____________________________
NO. REQUIRED: _______________________
OPTIONS & ACCESSORIES
(at additional charge)
Cleaning Accessories
28” long kettle draw-off brush
36” long clean up brush
8-1/2” long clean up brush
48” long kettle paddle
48” long kettle whip
Clean up pan
Tilting kettle accessory kit, includes draw-off brush,
36” clean up brush, 8-1/2” clean up brush, whip, solid
strainer and pan holder
300,000 BTU firing rate
One-piece lift-off stainless steel cover
Stainless steel wire basket
Steam Take-Off kit
Prison package, includes lockable stainless steel covers,
tamper proof screws, (4) 6” adjustable flanged feet
6” Flanged Feet
Filter System
60” water hose with quick disconnect
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
www.mfii.com
G
(1) 6 GALLON & (1) 10 GALLON TILTING
KETTLES ON A GAS STEAM BOILER
DETAILS & DIMENSIONS
SERVICE CONNECTIONS
G Gas Connection - 3/4” (19mm) N.P.T. female for
200,000 BTU boiler.
G1 Gas Connection - 1” (25mm) N.P.T. female for
300,000 BTU boiler.
CW1 Cold Water - 3/8” (10mm) NPT for cold water
to boiler. Cold water lines will have a maximum
of 50 PSI (3.5kg/cw2) and a minimum of 25 PSI
(1.8 kg/cw2) water pressure.
CW2 Cold Water - 3/8” (10mm) NPT for cold water to
condenser and kettle fill faucet. Cold water lines
will have a maximum of 50 PSI (3.5kg/cw2) and a
minimum of 25 PSI (1.8 kg/cw2) water pressure.
HW Hot Water - 3/8” (10mm) NPT female for hot
water to kettle fill faucet. Hot water line will
have a maximum of 50 PSI (3.5kg/cw2) and a
minimum of 25 PSI (1.8 kg/cw2) water pressure.
D Drain - Pipe full 2” (50mm) NPT to flush floor
drain capable of receiving water flowing at a
maximum rate of 5 gallons (19 liters) per minute. DO NOT MAKE SOLID CONNECTION TO
FLOOR DRAIN. DO NOT INSTLALL ELBOWS
IN DRAIN LINE.
EC Electrical Connection - 120 Volts AC, 60 Hz,
single phase, and a 9 foot Power Cord/NEMA
Two Gas Tilting Kettles
FOOD SERVICE EQUIPMENT
5-15.
ST Steam Take-off - Connection for operations of
adjacent steam powered equipment. Requires
steam take-off kit (optional at extra cost).
WATER SUPPLY
Good quality water feed is the responsibility of the owner. Water quality
must be within the following general guidelines.
TDS: 40-125 ppm Hardness: 35-100 ppm Chlorine: <0.2 ppm
Silica: <13 ppm Chlorides: <25 ppm
Chloramine: <0.2 ppm pH: 7.0 - 8.5
The best defense against poor water quality is a water treatment system
designed to meet your water quality conditions.
DIMENSIONS ARE IN INCHES [MM]
5 [127]
36 [914]
EC
FLUE
ST
5 [127]
G1
G
2.75 [70]
10.5
[267]
33
[838]
12.5
[318
10.5
[267]
CW2
HW
4[102]
2.5 [64]
D
CW1
8.5
[216]
3 [76]
Notes: If equipment is installed where elevation exceeds
2,000 feet (609.6 meters) above sea level, specify installation altitude so that proper gas orifices can be provided.
The only available space to supply utilities to the gas boiler
is the 6” (152mm) space between the floor and the cabinet.
Allow 3” (76mm) space from side wall and 6” (152mm) from
rear wall if adjoining walls are combustible.
PVC & CPVC PIPE ARE NOT ACCEPTABLE MATERIALS
FOR DRAINS.
CAUTION: REMOTE KETTLE OPERATION If this boiler
is feeding a remote kettle that will be more than 5 feet (1.5
meters) away, consult factory before ordering.
The manufacturer reserves the right to modify materials and specifications without notice.
PRINTED IN U. S. A.
SPEC SHEET: 14-0125 Rev D (4/16)
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
58
[1473]
10 gal
kettle
55.25
[1403
6 gal
kettle
22
[559]
ST
8 [203]
EC
27
[686]
28
D
HW
CW2
G
CW1
G1
[711]
6 [152]
www.mfii.com
Loading...