Market Forge MT10T10G300A User Manual

TWO GAS 10 GALLON

G

MODELS: □ MT10T10G200A

□ MT10T10G300A

SIZE: 36” x Wide x 33” Front-to-Back

(914mm Wide x 838mm Front-to-Back)
Height without Handle: 47.5” (1200mm)
Height with Handle: 58.5” (1500mm)

DESCRIPTION:

Market Forge Model ________ Steam Jacketed Tilting
Kettles. Kettles will be mounted on a 28” (711mm) high
cabinet base. Hot and cold water  ll faucet, depressed
area and drains, and steam control valve will be located on

stainless steel marine-edged counter-top. A 4” (120mm)
deep clean-up pan 12” x 10” (305mm x 254mm) with re-

movable splash guard will be standard. Splash guard will
be removable so that it may also be attached to a food

receiving pan. Kettle made from #316 stainless steel will
A.S.M.E approved and National Board Registered.

TILTING KETTLES

JOB NAME: ________________________
ITEM NO.: _________________________
NO. REQUIRED: ____________________

SPEC SHEET: S-2159A

10/12

Cabinet base, constructed of a stainless steel frame,
which houses the gas  red boiler, will be of modular de­sign to match other Market Forged cooking equipment.
Base will be equipped with 6” (125mm) stainless steel

marine-edged countertop and hinged doors with magnet-

ic latches. Units will be polished stainless steel.

CAPACITY:

■ MT10T10G - Two 10 Gallon (38 liters)

OPERATION SHALL BE BY:

Gas  red, 15 PSI (1kg/cm2), A.S.M.E constructed and
National Board Registered steam boiler rated at:

□ 200,000 BTU (Standard)
□ 300,000 BTU (Optional at Extra Cost)

Boiler will be equipped for:

□ Natural Gas
□ LP Gas

Manifold and pilot gas pressure will be 3 1/2” (89mm) for

Natural Gas and 10” (254mm) for LP Gas. Incoming gas
pressure must not exceed 14” (357mm) W.C.

The manufacturer reserves the right to modify materials and speci cations without notice.

Boiler will be automatically  lled with hot water and
brought to 15 PSI (1kg/cm2) pressure when heat and

water switches are turned on and automatically drained
under pressure when switches are turned off. Automatic
cold water condenser will condense exhausted steam

into water before releasing it to drain. Unit also includes
safety valve, low water cut-off, water strainer, and des-

caler.

OPTIONAL AT EXTRA COST:

□ One-piece lift-off stainless steel cover
□ Stainless steel wire basket
□ Clean-up brush
□ Steam Take-Off kit
□ Total Concept Boiler Descaling Chemical

FOOD SERVICE EQUIPMENT

Two 10 Gallon Tilting Kettles

Tel: [phone] • Fax: [phone] (Ex. MA) • [phone] (MA and Overseas)

E-Mail: CUSTSERV@m i.com • Website: www.m i.com

35 Garvey Street • Everett • MA • 02149

SPEC SHEET: S-2159A

28"

ST

43mm

HW

CW

5"

ST

G1

76mm

3"

400mm

15 3/4"

1 3/4"

D

102mm

4"

152mm

D

G1

G

6"

8"

205mm

EC

ST

471mm

18 1/2"

33"

G

51mm

610mm

(100 or 200K)

445mm

17 1/2"

24"

(300K)

5"

127mm

2"

2 3/4"

70mm

(100 or 200K)

EC

5 1/2"

369mm

838mm

ST

280mm

10 1/2"

36"

64mm

FLUE

914mm

2 1/2"

127mm

CW

HW

58"

1473mm

711mm

22"

559mm

10/12

Two 10 Gallon Tilting Kettles

FOOD SERVICE EQUIPMENT

G

TWO GAS 10 GALLON

TILTING KETTLES

DETAILS & DIMENSIONS

SERVICE CONNECTIONS

Gas Fired

G Gas Connection - 3/4 (19mm) NPT 200,000 BTU

G1 Gas Connection - 1 (25mm) NPT 300,000 BTU

HW

Hot Water - 3/8” (9.5mm) O.D. tubing for hot water to

generator. Hot water lines will have a maximum of 50
PSI (3.5kg/cm2) and a minimum of 25 PSI (1.8kg/

cm2) water pressure.

CW

Cold Water - 3/8” (9.5mm) O.D. tubing for cold water

to condenser. Cold water lines will have a maximum

HWK

of 50 PSI (3.5kg/cm2) and a minimum of 25 PSI
(1.8kg/cm

1/2” (13mm) O.D. tubing for hot water to kettle ll

2

) water pressure.

faucet.

CWK

1/2” (13mm) O.D. tubing for cold water to kettle ll
faucet.

D

Drain - Pipe full 2” (50mm) I.P.S. to ush oor drain

capable of receiving water owing at a maximum rate

of 5 gallons (19 liters) per minute. DO NOT MAKE
SOLID CONNECTION TO FLOOR DRAIN.

EC

Electrical Connection - 115 VAC, 60 Hz, 2 amps, 1/2”
(13mm) conduit connection or equivalent. Use wire
suitable for at least 90°C.

ST*

Steam Take-Off - Connection for operation of adja­cent steam-powered equipment

* Steam supply connection available on either side of
cabinet base.

NOTES: Allow 3” (76mm) space from side wall and 6”
(152mm) from rear wall if adjoining wall is combustible.

If unit is to be installed where elevation exceeds 2,000’
(609.6 meters) above sea level, specify installation altitude

so that proper gas orices can be provided.

PVC & CPVC pipe are not acceptable materials for drains.

CAUTION:

Before connecting water to this unit, water supply should
be analyzed to make sure hardness is no greater than 2.0

grains per gallon and pH level is within the range of 7.0-

8.5. Water that fails to meet these standards should be
treated by installation of water conditioner. EQUIPMENT

FAILURE CAUSED BY INADEQUATE WATER QUAL­ITY IS NOT COVERED UNDER WARRANTY.

It is our policy to build equipment which is design certied by U.L., A.S.M.E., N.S.F. and C.S.A. However, a continuing program of product improvement makes

it necessary to submit new models to the agencies as they are developed and consequently not all models bear the appropriate agency labels at all times.

PRINTED IN U.S.A.

Tel: [phone] • Fax: [phone] (Ex. MA) • [phone] (MA and Overseas)

E-Mail: CUSTSERV@mi.com • Website: www.mi.com

35 Garvey Street • Everett • MA • 02149