Page 1
TWO 10 GALLON
DS
MODEL
MT10T10 - (2) ten gallon (38 liter) direct steam tilting kettles
on cabinet base
DESCRIPTION
Will be a Market Forge Model MT10T10, consisting of two 10
gallon (38 liter) type 316 stainless steel, tilting, steam jacketed
trunnion kettles. Kettles will be mounted on a 28” (711mm) high
cabinet base. Hot and cold water fill faucet, depressed area and
drains, and steam control valves will be located on stainless steel
marine edged counter-top. A 4” (102mm) deep, 12” x 10” (305mm
x 254mm) clean-up pan with removable splash guard will be
standard. (Splash guard will be removable so that it may also be
attached to a food receiving pan).
Kettle will be A.S.M.E. approved and National Board Registered.
Cabinet base will be of modular design to match other Market
Forge cooking equipment. Base with stainless steel frame will
be equipped with 6” (152mm) stainless steel legs and adjustable
bullet feet, reinforced die formed stainless steel marine edged
counter-top, and stainless steel lift-off front cover Unit will be
polished stainless steel.
DIRECT STEAM TILTING KETTLES
JOB NAME: ___________________________
ITEM NO.: ____________________________
NO. REQUIRED: _______________________
OPERATION SHALL BE BY:
Direct Steam at 15-50 PSI (1.0-3.5 kg/cm2) 1/3 BHP required
per kettle. Over 50 PSI (3.5 kg/cm2), a pressure reducing valve
is required.
Two Direct Steam Tilting Kettles
FOOD SERVICE EQUIPMENT
SHIPPING WEIGHT
400 lbs (181 kg)
OPTIONS & ACCESSORIES
(at additional charge)
Cleaning Accessories
28” long kettle draw-off brush
36” long clean up brush
8-1/2” long clean up brush
48” long kettle paddle
48” long kettle whip
Clean up pan
Tilting kettle accessory kit, includes draw-off brush,
36” clean up brush, 8-1/2” clean up brush, whip, solid
strainer and pan holder
One piece lift-off stainless steel cover
Stainless steel wire basket
Pressure reducing valve
Condensate return kit
Ball float trap
Prison package, includes lockable stainless steel covers,
tamper proof screws, (4) 6” adjustable flanged feet.
6” Flanged Feet
60” water hose with quick disconnect (2) required.
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
www.mfii.com
Page 2
DS
TWO 10 GALLON
DIRECT STEAM TILTING KETTLES
DETAILS & DIMENSIONS
SERVICE CONNECTIONS
S* Steam Supply - 3/4” (19mm) NPT for incoming steam
at 15-50 PSI (1.0-3.5kg/cm2).
HW Hot Water - 3/8” (10mm) NPT for hot water to faucet.
Hot water line will have a maximum of 50 PSI (3.5kg/
cw2) and a minimum of 25 PSI (1.8 kg/cw2) water
pressure (Water may be filtered).
CW Cold Water - 3/8” (10mm) NPT for cold water to
faucet. Cold water line will have a maximum of 50 PSI
(3.5kg/cw2) and a minimum of 25 PSI (1.8 kg/cw2)
water pressure.
D Drain - Pipe full 2” (50mm) IPS to flush floor drain.
DO NOT MAKE SOLID CONNECTION TO FLOOR
DRAIN.
CR** Condensate Return - 1/2” (13mm) IPS for incoming
condensate return from kettle may be connected to
condensate return line.
* Pressure reducing valve is required if incoming pressure
exceeds 50 PSI (3.5kg/cm2).
**Optional at extra cost.
WATER SUPPLY
Good quality water feed is the responsibility of the owner. Water
quality must be within the following general guidelines.
TDS: 40-125 ppm Chlorides: <25 ppm
Silica: <13 ppm pH: 7.0 - 8.5
Two Direct Steam Tilting Kettles
Chloramine: <0.2 ppm Chlorine: <0.2 ppm
FOOD SERVICE EQUIPMENT
Hardness: 35-100 ppm
The best defense against poor water quality is a water treatment
system designed to meet your water quality conditions.
Appliance to be installed with backflow protection according to
federal, state or local codes.
DIMENSIONS ARE IN INCHES [MM]
4 [102]
CW
12
10.5
[267]
58
[1473]
8.5
[216]
HW
15 [381]
18 [457]
[305]
4 [102]
2.5 [64]
36 [914]
CR
D
S
33
[838]
6 [152]
PRINTED IN U. S. A.
SPEC SHEET: 14-0119 Rev C (12/15)
18
[457]
CW
HW
The manufacturer reserves the right to modify materials and specifications without notice.
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
28
S
CR
D
[711]
6 [152]
www.mfii.com
Loading...