Market Forge FT-20LF User Manual
DIRECT STEAM TILTING
D
MODELS
FT-20LF - 20 gallon (76 liter), direct steam, tilting, fully jack-
eted, tri-leg kettle
FT-30LF - 30 gallon (114 liter), direct steam, tilting, fully jack-
eted, quad-leg kettle
FT-40LF - 40 gallon (152 liter), direct steam, tilting, fully jack-
eted, quad-leg kettle
FT-60LF - 60 gallon (227 liter), direct steam, tilting, fully jack-
eted, quad-leg kettle
DESCRIPTION
Will be a Market Forge direct steam connected, tilting tri-leg, steam
jacketed. Kettle will be constructed of welded satin finish stainless
steel, type 304. A double wall kettle interior will form a full jacket
around the lower of the kettle. The kettle bottom will be of elliptical
design for superior heat circulation.
The 20 gallon will be on a Tri-leg mounting frame of stainless steel
pipe and the 30-60 gallon will be on a Quad-leg mounting frame
of stainless steel pipe. Both the Tri and Quad stainless steel pipe
mounting frames will conceal the steam piping. Each leg will be fitted with a four-hole adjustable flange foot for securing to the floor.
A sealed stainless steel tilt mechanism will permit the kettle to tilt
forward a full 90o for complete emptying. Tilting mechanism will
be self-locking for positive stop action. Steam control valve will be
Tilting, Fully Jacketed Kettles
mounted on right hand control box.
FOOD SERVICE EQUIPMENT
Unit will include as standard a steam control kit (CKT-1), and a
Steam trap that includes a steam control valve (steam inlet globe
valve) and line strainer.
OPERATION WILL BE BY
Direct steam at 5-35 PSI (0.3-2.5 kg/cm2). Over 35 PSI (2.5 kg/
cm2), a pressure reducing valve is required.
STEAM FLOW REQUIREMENTS
34 lbs. (15.5 kg) steam per hour or 1 BHP per 20 gallons (76 liters)
pf kettle capacity.
MODEL BHP/Hour Lbs. Steam/Hour
FT-20LF 1.0 34.5
FT-30LF 1.5 52.0
FT-40LF 2.0 69.0
FT-60LF 3.0 103.5
TRI-LEG & QUAD-LEG KETTLES
JOB NAME: ___________________________
ITEM NO.: ____________________________
NO. REQUIRED: _______________________
FT-40LF shown
SHIPPING WEIGHT
FT-20LF - 225 lbs (102 kg)
FT-30LF - 275 lbs (125 kg)
FT-40LF - 300 lbs (136 kg)
FT-60LF - 315 lbs (143 kg)
OPTIONS & ACCESSORIES
(at additional charge)
Covers
One-piece lift-off stainless steel cover.
One-piece counterbalance hinged stainless steel cover.
Pantry Faucets
Double pantry faucet with swing spout and
mounting bracket.
Single pantry faucet with swing spout and mounting
bracket.
Draw-off
2” draw-off valve with strainer.
3” draw-off valve with strainer. Triple basket assembly.
Check valve.
Wall models (consult factory).
Graduated measuring stick.
BFT - ball float trap.
PRV - pressure reducing valve.
Type 316 stainless steel liner for high acid content products.
Etched Gallon Markings.
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
www.mfii.com
D
DIRECT STEAM TILTING
TRI-LEG & QUAD-LEG KETTLES
DETAILS & DIMENSIONS
DIMENSIONS
MODEL A B C D E F G H (2”) H (3”) J (2”) J (3”) K L M
26
FT-20LF
FT-30LF
FT-40LF
FT-60LF
[660]
29.5
[749]
33
[840]
35.5
[902]
15.75
[400]
17.5
[445]
19.25
[489]
20.5
[521]
34.75
[883]
34.5
[876]
33.75
[857]
35
[889]
39.75
[1010]
43.25
[1100]
46.75
[1185]
49.25
[1251]
33.5
[850]
37
[940]
40.5
[1030]
43
[1092]
20.25
[514]
21.5
[546]
20
[508]
21
[533]
- 13
[330]
- 15.5
[394]
- 14.5
[368]
- 18
[457]
15.25
[387]
15.5
[394]
16.25
[413]
20.25
[514]
12.5
[318]
14.5
[368]
12.5
[318]
10.5
[267]
12
[305]
14
[356]
12
[305]
10
[254]
63
[1600]
65.63
[1667]
67.25
[1709]
71.88
[1826]
NONE 16.38
9.5
[241]
11
[279]
12.5
[318]
[416]
18.38
[467]
19.88
[505]
21.5
[546]
DIMENSIONS ARE IN INCHES [MM]
SAFETY RELIEF VALVE
STRAINER AND
STEAM TRAP
(OPTIONAL)
2” VALVE:
CLOSED 5.13 [130]
OPENED 6.88 [175]
3” VALVE:
CLOSED 7.88 [200]
Tilting, Fully Jacketed Kettles
OPENED 10.13 [257]
CR
FOOD SERVICE EQUIPMENT
K
JACKET
DRAIN VALVE
L L
45°
ØA
SPRING ASSISTED
COVER (OPTIONAL)
NOTE: 30, 40, & 60 GALLON
KETTLES ARE SUPPLIED WITH
2 REAR SUPPORT LEGS.
S
FLANGED FEET DETAIL
4 EQUALLY SPACED Ø7/16 [11]
HOLES ON 3 [76] B.C.
B
C
SERVICE CONNECTIONS
S Steam Supply - 3/4” IPS (19mm) at 5-35 PSI (0.3-
2.5 kg/cm2). Over 35 PSI (2.5 kg/cm2). Pressure
reducing valve is required if incoming pressure
exceeds jacket rating.
CR Condensate Return - 1/2” IPS (13mm)
FAUCET (OPTIONAL)
2” OR 3” TANGENT
DRAW-OFF VALVE
(OPTIONAL
S
F
J
E
D
It is our policy to build equipment which is design certified by A.S.M.E., C.S.A. and N.S.F. However, a continuing program of product improvement makes it
necessary to submit new models to the agencies as they are developed and consequently not all models bear the appropriate agency labels at all times.
The manufacturer reserves the right to modify materials and specifications without notice.
PRINTED IN U. S. A.
SPEC SHEET: 14-0142 Rev A (7/14)
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
H
G
M
www.mfii.com
Loading...