Mark PAR 36 ECO User Manual

EN

PAR 36 ECO

CAUTION. Keep the device away from rain and moisture. Unplug mains lead before opening the housing. For

your own safety, please read this user manual carefully before you initial start-up.

Every person involved with the installation, operation and maintenance of this device have to:

- Be qualified

- Follow the instructions of this manual

INTRODUCTION

- Thank you for having chosen PAR 36 ECO spot. This spot is ideal for party rooms and small discotheques.

- Unpack your PAR 36 ECO

- Before you initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult with your dealer and do not use the device.

SAFETY INSTRUCTIONS

- If the external flexible cable or cord of this sport is damaged, it shall be exclusively replaced by the manufacturer
or his service agent or a similar qualified person in order to avoid a hazard.

- Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an e
xtent that their effectiveness is impaired, for example by cracks or deep scratches.

- The lamp shall be changed if it has become damaged or thermally deformed.

- This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will
not accept liability for any resulting defects or problems.

- If the device has been exposed to drastic temperature fluctuation (e.g. After transporting), do not switch
inmediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.

- During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.

- Do not toucj the device housing bare-handed during its operation (housing become hot)

- Do not switch the pins on and off in short intervals as this would reduce the lamp´s life.
HEALTH HAZARD Nevel look directly into the light source, as sensitive persons may suffer an epileptic shock

- Please considerer that damages caused by manual modifications to the device are not subject to warranty.
OPERATION DETERMINATIONS This device was designed for indoor use only.

- Do not shaeke the device. Avoif brute force when installing or operating the device.

- You can install the device at any desired place in dry rooms. Please make sure that the device is not
exposed to extreme heat, moisture or dust. There should not be any cables lying around. You endanger
your own and the safety of others.

- Operate the device only after having familirized with its functions. Do not allow an operation by persons
who do not know the device well enough. Most damages are the result of an unprofessional operation.

- Please consider that for safety reasons unauthorized modifications to the device are forbidden.

INSTALLATION
DANGER OF FIRE When installing the device, make sure there is no highly-inflammable material within

a distance of min. 0.5 m

- This device fall under protection class I. Therefore is essential that the yellow/green conductor get
connected to earth.

Rev. 13.01

EN

- Install the lamp (6 V/30 W PAR 36) in the housing. Please remove the fixation ring by pressing it together.
Connected the wires with the lamp using a flat-blade screwdriver. Insert the lamp in the housing. Place
the lens onto the bulbb. Fix the lamp and the lens with the fixation ring. Please refer to the following drawing.

- For ceiling and wall mounting fix the device with the mounting bracket onto the desired installation place.
This device must be earthed.

- This device es not suitable for mounting on flammable
surfaces.

- Connect the spot to the mains.

OPERATION

- After you connected the device to the mains, the lamp starts burning. Adjust the light´s angle to get the
best results.

- Unplug or disconnect the PAR 36 spot from ther mains, when you are not using it.

REPLACING THE LAMP

Warning: Before replacing the lamp, unplug the pin spotlight. Be sure the lamp has cooled down, or wear a thick

glove when replacing it.
Caution: Use only a PAR 36 6 V 30 W lamp. Using another type and size lamp could damage the lamp or the
pin spotlight.

- Remove the fixation ring by pressing it togheter

- Turn the pin spot light with the lamp side down so the lamp falls out.

- Use a flat-blade screwdriver to loosen the two screws that secure the wire to the bulb´s terminal. Remove
the old bulbl and discard it.

- Reconnect the two wires to the screws on the new lamp and tighten the screws securely. Insert the new
lamp into the housing.

- Replace the lens and fix the lamp and the lens with the fixation ring.

SPECIFICATIONS

Power supply: AC 220 - 240 V, 50 Hz, 36 W
Fitting lamps: 6 V/30 W PAR 36

Este símbolo en su equipo o embalaje, indica que el presente producto
no puede ser tratado como residuos domésticos normales, sino que deben
entregarse en el correspondiente punto de recogida de equipos electrónicos
y eléctricos. Asegurándose de que este producto es desechado
correctamente, Ud. está ayudando a prevenir las consecuencias negativas
para el medio ambiente y la salud humana que podrían derivarse de la
incorrecta manipulación de este producto. EL reciclaje de materiales
ayuda a conservar las reservas naturales. Para recibir más información,
sobre el reciclaje de este producto, contacte con su ayuntamiento, su
punto de recogida más cercano o el distribuidor donde adquirió el producto.

HOUSING

PAR 36 6V 30W LAMP

LENS (NOT INCLUDED)

FIXATION RING