Mark PAR-16 User Manual
PAR-16
For your own safety, please read this user manual carefully
before you start-up and use.
SAFETY INSTRUCTIONS
? CAUTION!
electric shock when touching the wires!
Keep away from heaters and other heating sources!
?
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
?
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an
?
extent that their effectiveness is impaired, for example by cracks or deep scratches.
Always disconnect from the mains, when the device is not in use or before cleaning it.
?
Keep away children and amateurs from the device!
?
This device is a spot designed for professional use on stages, in discotheques, theatres etc. this fixture
?
is only allowed to be operated with an alternation current of max. 230V/50/60Hz 50W and was designed
for indoor use only.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that
?
the device will serve you for a long time without defects.
Do not shake the device. Avoid brute force when installing or operation the device.
?
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
?
moisture or dust. There should not be any cables lying around. You endanger your own and the safety
of others!
? The symbol
between light-output and the illuminated surface must be more than 0.5 meter.
The maximum ambient temperature T
?
Operate the device only after having become familiar with its functions. Most damages are the result of
?
unprofessional operation!
Please use the original packaging if the device is to be transported.
?
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
?
If this device will be operated in any way different to the one described in this manual, the product may
?
suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
dangers like short-circuit, burns, electric shock, lamp explosion, crash etc.
Replacing the lamp
DANGER TO LIFE!
?
? CAUTION!
Before replacing the lamp, unplug mains lead and let the lamp cool down (approx. 5 minutes).
?
During the installation do not touch the glass-bulbs bare-handed! Please follow the lamp manufacturer? s
?
notes!
Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the
?
device was not designed for. Damages caused by non-observance are not subject to warranty.
For the installation, you need one Cool-Beam 12V GX-5.3 lamp with up to max. 50W
?
? Procedure:
Step 1: Open the housing cover by pulling the extension spring.
Step 2: If replacing the lamp, remove the old lamp from the lamp socket.
Step 3: Insert the new Cool-Beam 12V/50W GX-5.3 lamp into the spot.
Step 4: Close the device.
Please be advised that for proper use an appropriate safety transformer for 12V halogen lamps is
Do not operate this device with opened housing cover!
?
Installing
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch
?
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
M
determines the minimum distance from lighted objects. The minimum distance
must never be exceeded.
a
Only install the lamp with the device switched off! Unplug from mains before!
The lamp has to be replaced when it is damaged or thermally deformed due to the heat!
necessary.
? The device should be installed outside areas where persons
may walk by or be seated.
? IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE
EXPERIENCE, including (but not limited to) calculation working
load limits, installation material being used, and periodic safety
inspection of all installation material and the projector.
? The device has to be installed out of the reach of people.
(1)Colour filter trame
(2)Clip-to-hold clamps
(3)Tube
(4)Mounting-bracket
(5)Extension spring
(6)Housing cover
(7)Mounting bracket screws
? Before rigging make sure that the installation area can hold a
minimum point load of 10 times the device? s weight.
? DANGER OF FIRE! When installing the device, make sure
there is no highly inflammable material (decoration articles, etc.)
within a distance of min. 0.5 M.
? For overhead use, always install a safety-rope that can hold at
least 10 times the weight of the fixture.
? Adjust the desired inclination-angle via the mounting-bracket and fix the fixation screws.
Connection with the mains
? DANGER TO LIFE! The electric connection must only be carried out by a qualified electrician!
? In order to connect the device to the mains, you have to install a n appropriate transformer
with a 12 V at least 60 W output (per PAR 16 spot)
OPERATION:
?
After toy connected the device to the mains, you can control the device via your lighting controller
CLEANING AND MAINTENANCE
The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert
after every four years in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled
person once a year.
The following points have to be considered during the inspection:
1) All screws used for installing the devices or parts of the device have to be tighly connected and must not be
corroded.
2) There must not be any deformations on housings, fixations and installation spots (ceiling, suspension, trussing).
3) The electric power supply cables must not show any damages
? DANGER TO LIFE! Disconnect from mains before starting
? There are no serviceable parts inside the device except for
only to be carried out by authorized dealers.
TECHNICAL SPECIFICATIONS
Power supply:
Max.230-240V/AC, 50Hz
Power consumption, Max.50W
Dimensions (L x W x H); 92x92x120mm
Weight: 0.2 kg
Fitting lamp Max12V/50W GX-5.3
Maximum ambient temperature Ta: 45°C
Maximum housing temperature TB: 160°C
Minimum distance: 0.5m
Este símbolo en su equipo o embalaje, indica que el presente producto
no puede ser tratado como residuos domésticos normales, sino que deben
entregarse en el correspondiente punto de recogida de equipos electrónicos
y eléctricos. Asegurándose de que este producto es desechado
correctamente, Ud. está ayudando a prevenir las consecuencias negativas
para el medio ambiente y la salud humana que podrían derivarse de la
incorrecta manipulación de este producto. EL reciclaje de materiales
ayuda a conservar las reservas naturales. Para recibir más información,
sobre el reciclaje de este producto, contacte con su ayuntamiento, su
punto de recogida más cercano o el distribuidor donde adquirió el producto.
maintenance operation!
the lamp. Maintenance and service operations are
Loading...