Mark MULTIPAR 575/2 User Manual

User Manual / Instrucciones de Usuario

MULTIPAR 575/2

V. 2

MULTIPAR 575/2

Version Español .............. Página 5

English Version ............... Page 1

Colour frame

Lens catcher

Yoke locking knob

Retaining clip

Lens

1. Before you initially start-up, please make sure that there is no damage caused by transportation. Should there be any,
consult your dealer and do not use the device.

2. CAUTION! Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when
touching the wires! Keep away from heaters and other heating sources!

3. Do not mount the device on or near combustible sufaces. Do not operate the device without a lens installed.

4. Always hang the device with the color frame retaining clip in the locked position.

5. This device falls under protection-class I, therefore it is essential that the yellow/green conductor gets connected to

earth. The electric connection must be carried out by a qualified employee.

6. Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord
from time to time.

8. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or

his service agent or a similar qualified person in order to avoid a hazard.

9. Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that
their effectiveness is impaired, for example by cracks or deep scratches.

10. Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the

mains with particular caution!

11. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by
the plug. Never pull out the plug by tugging the power-cord.

12. During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean
that the device is defective.

13. DANGER OF BURNING! Never touch the device during the operation! The housing heats up to the housing
temperature TSURFACE.

14. Don't switch the device on and off in short intervals as this would reduce the lamp's life.

15. HEALTH HAZARD! Never look directly into the light source, as sensitive persons may suffer an epileptic shock

(especially meant for epileptics)!

16. Keep away children and amateurs from the device!

17. There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by

authorized dealers.

IMPORT

ANT SAFETY

INSTRUCTIONS

Spring clip

Colour frame holder

Tabs

Lens rotation ring

Lamp
housing

Yoke

Accessories

Color frame 407CF

Wide Flood lens 400-WFL

Very Narrow Spot lens

400-VNSP
Narrow Spot lens 400-NSP
Medium Flood lens 400-MFL

MULTIPAR 575/2

- 1 -

MULTIPAR 575/2

Lenses for the MULTI PAR come in four versions. The type or beam spread can be identified by the lens texture.

2.Loosen the knurled bolt on the back of the lamp housing and pull the housing
straight out from the back of the fixture.

3.Remove the GKV lamp from its box, holding it by the base.
Note: To avoid premature lamp failure , do not touch the lamp glass with your
fingers. If you touch the lamp during installation, clean it carefully with
rubbing alcohol and a clean, lint -free cloth before operation .

4.Line up the flat sides of the lamp base with the brackets on either side of the
socket (Figure 2).

5.Push down on the lamp base until the lamp is firmly seated. Make sure that the
lamp is fully seated, with the bottom of the lamp heat sink flush to the lamp housing casting.
Caution! lmproperly installed lamps cause premature lamp failure and socket problems .

6.To reinstall the lamp housing, center it on the reflector and the bolt hole, then tighten the knurled bolt to secure the
lamp housing in place.

WARNING! Let lamp cool before changing .

Always replace the lamp if it becomes damaged or deformed.
Verify that the GKV lamp you use is suitable for the voltage at your facility. 115,

120, 230, and 240 volt GKV lamps are available.

Caution! Operating lamps above their rated voltage reduces lamp life and can
cause premature lamp failure .

1.Disconnect the unit from power before installing the lamp.

1.Release the retaining clip by pushing it sideways. The retaining clip opens.

2.lnsert the color frame.

3.Press the retaining clip down until it locks.
Note: Use only color frames or top hats with 6.7-inch inside diameter.

Cleaning the reflector

1.Remove the lens so you can access the reflector from the front of the fixture. See Removing a lens on page 2

2.Remove dust with a blast of oil free air, or wipe with a clean, soft, lint-free cotton cloth. lf this is sufficient to remove

dust, go to step 5. Otherwise, continue to step 3.

3.Dampen a clean, soft, lint-free cotton cloth with a mild, soapy water solution and gently wipe the reflector.

4.Remove any soapy water residue with a clean, soft, lint-free cotton cloth dampened with water.

5.Reinstall a lens before using the fixture.

The following recommendations are offered when cleaning and inspecting lenses and reflectors:
Do not use glass and window cleaners on the reflector. Chemicals in these cleaners will harm the reflective coating.
Do not use paper towels or harsh materials to wipe the reflector. These materials can scratch the surface of the reflector.

WARNING! Unplug the fixture before attempting to clean reflector .

Figure 1

Color frame retaining clip

WARNING! Hang the MUL

TI PAR

with the color frame retaining clip in the locked position

.

The color frame holder is equipped with a spring-loaded retaining clip that prevents color

frames and accessories from falling out.

Lens identification

Retaining clip in
the locked position

Very narrow spot
Clear glass

15º Round beam shape

VNSP

Installing the GKV Iamp

Lamp housing

Figure 2

Wide flood
Many facets,sized 6x12mm
30º x51º

Oblong beam shape

Medium flood
Fewer facets,sized 6x22mm
21º x34º

Oblong beam shape

Narrow spot
Stipple glass
19º Round beam shape

NSP

MFL WFL

Knurled bolt

Lamp brackets

HPL lamp

MULTIPAR 575/2

- 2 -