Mark MULTIPAR 162/3 User Manual

Rev. 16.04.01

MULTIPAR 162/3

User Manual / Instrucciones de Usuario

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the fixture.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

Disconnect main power before servicing and maintenance.

Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

In the event of serious operating problem, stop using the fixture immediately. Never try

to repair the fixture by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type spare parts.

Do not connect the device to any dimmer pack.

Do not touch any wire during operation and there might be a hazard of electric shock.

To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

The housing must be replaced if they are visibly damaged.

Do not look directly at the LED light beam while the fixture is on.

There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact your nearest dealer.

Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage

unit.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

MULTIPAR 162/3 User Manual/Manual de uso P 1

EN

2. Technical Specifications

Featuring 54 pcs 3W RGBW (16R+16G+16B+6W)

Each color of R, G, B, W, can be controlled individually.

DMX 8 channels

Smooth 0~100% dimming and variable strobe speeds.

Operation modes: DMX, Mater/Slave mode, audio

Ideal for discotheques, clubs, bars, parties, Mobile DJs, ect.

Input Voltage: AC 220V~240V 50/60Hz

Power consumption

Beam angle: :

160

25º

W

LED: 54 pcs 3W RGBW (16R+16G+16B+6W)

Dimension: 305 x 215 x 326 mm

Weight:

3,2

kg

3. Installation

The unit should be mounted via its screw holes on the handle.

Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is

out of the touch of people and has no one pass by or under it.

MULTIPAR 162/3 User Manual/Manual de uso P 2

EN

4. Setting the unit

4.1Rear Panel

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press ENTER button to

setup . Back to the functions without any change press MENU button. The main functions

are shown below:

MULTIPAR 162/3 User Manual/Manual de uso P 3

EN

1 . DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal.

2. Display: To show the various menus and the selected functio

3.Menu

To select the program functions

4.Up

To go forward in the selected functions

5.Down

To go backword in the selected functions

6.Enter

To confirm the selected funtions

7. Mains input：Connect to supply mains power.

8. DMX output：For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.