MarineTech KPS25C, KPS25A, KPS25B, KPS50C, KPS100C Installation Manual
...
SERVICE AND WARRANTY
Should your unit ever require service, please do not return the product to your dealer. Please
call the number below for special instructions on shipping and handling. Please call between
9:00 am - 3:00 pm (Central Standard Time) Monday through Friday. If service is required and
covered by warranty, it will be repaired or replaced as described below. If service is required
and not covered by warranty, replacement parts are available for purchase and may be paid for
by credit card.
The warranty coverage on this equipment is limited to the terms set
forth below:
MarineTech Products, Inc. warrants this product to be free of defects in material and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. Positive
proof of date of purchase is required for warranty service. If ser vice is r equir ed and covered by warranty, the unit will be repaired or replaced with new or factory rebuilt parts at no
charge. The defective components must be returned to the address specified, with shipping
charges prepaid. Be sure to include your name, address, telephone number and a copy of the
sales receipt showing the date of original retail purchase. All sales receipts are subject to verification.
This warranty does not apply if the unit has been damaged by accident, abuse, misuse, poor
installation or misapplication, or if it has been modified from its original condition, or if any
serial number has been removed or defaced or altered. This warranty does not cover any ex-
pense to remove or reinstall the unit or any of its components. If a r etur ned unit is not
covered by warranty, the sender will be notified and given an estimate of the charges to repair
or replace the unit, together with the return shipping charges.
Installation Manual
Transom Mount Models Only.
KPS25A KPS50A KPS100A
KPS25B KPS50B KPS100B
KPS25C KPS50C KPS100C
KPS50A
THIS WARRANTY DOES NOT COVER SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY,
OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED
TO DAMAGE TO OR REPLACEMENT OF OTHER EQUIPMENT AND PROP-
ERTY. THE WARRANTY AND REMEDIES SET FORTH ARE EXCLUSIVE
AND IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS
OR IMPLIED. DUE TO THE SPECIAL AND UNIQUE CONDITIONS THAT
MAY EXIST IN EACH APPLICATION, THE MANUFACTURER SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO DEALER, AGENT
OR EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION, EXTENSION OR ADDITION TO THIS WARRANTY.
Some states do not allow exclusion of incidental or consequential damages, so the above ex-
clusions may not apply to you. This warranty gives you specific legal rights, and you may also
have other legal rights, which may vary from state to state.
For service or replacement parts, visit our website or contact
our customer service department. Send an email to:
service@marinetechproducts.com or call 651-486-6989
MarineTech Products, Inc.
1360 East County Road E
Vadnais Heights, MN 55110
www.marintechproducts.com
Introduction
Required Tools For Installation
Thank you for purchasing your new KingPin Anchor system. Please read
through these operating instructions so you will know how to install and
operate your model properly.
Safety Precautions
The safety precautions for this KingPin Anchor system have been pre-
pared to assist the operator in the performance of good safety proce-
dures.
Warning!!
Only engage KingPin Anchor pole when stopped. NEVER MOVING.
Disengage KingPin Anchor pole before moving the watercraft. ALWAYS
be aware of your surrounding while moving with KingPin Anchor pole in
its mount. Take CAUTION around bridges, low hanging trees, power
lines, Etc. Make sure KingPin Anchor pole is securely stored before
trailering boat. Always use the comfort grips while handing the KingPin
Anchor pole. Never step on the KingPin Anchor mount. Take CAUTION
articles of clothing could get snagged on the KingPin Anchor mount.. Use
caution while docking with KingPin Anchor mount attached to watercraft.
FAILURE TO HEED TO ANY OF THESE INSTRUCTIONS MAY RESULT
IN DAMAGE TO YOUR KINGPIN ANCHOR SYSTEM, WATERCRAFT,
AND/OR SERIOUS PERSONAL INJURY OR DEATH.
13/64” Drill Bit Phillips Bit
Power Drill Marker
Installing the KingPin Anchor
1.) First use the base of the anchor as a template for marking hole
location.
2.) Drill holes using a 13/64” drill.
3.) Place 5/8” O-Rings in countersink grooves on the boat
side of Base Plate.
4.) Align and secure anchor with machine screws. CAUTION
over tightening may cause screws to strip.
The hardware installation is complete. Your KingPin Anchor is
ready for use.
Machine Screws
Kit Includes
(1) 5 or 10 In. Transom (4) O-Rings 5/8” (4) Machine Screws
*Note: Kit does not include the (2) Rubber Pole Clips shown below.
* Included with Pole Kit Only
Watercraft
13/64 Drill Holes
5/8” O-Rings
Base Plate
Loading...