marinco SPL-12W, SPL-12B, SPL-12C User Manual
Precision Spotlight Instructions Precision Spotlight Instructions
For more information and installation guides, visit
our website: www.marinco.com
For a FREE catalog of Marinco Recreational
Group products, contact your local dealer or visit
Marinco.com.
marinco.com
ZX447
MAR_TL_029_1011
LIMITED WARRANTY
For five (5) years from the date of purchase, Marinco will, at its discretion, repair or replace
for the original consumer, free of charge, any part or parts found upon examination by
Marinco to be defective in material or workmanship or both. All transportation charges under
this warranty must be borne by the consumer.
Proof of purchase is required. Proof of purchase must be a computerized receipt.
Handwritten receipts are not accepted.
THERE IS NO OTHER EXPRESSED WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR FROM THE DATE OF PURCHASE. THIS IS THE EXCLUSIVE REMEDY AND
CONSEQUENTIAL DAMAGES ARE EXCLUDED WHERE PERMITTED BY LAW.
FCC
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
502-2 & 503-2 instructions
Instructions
marinco.com
Installing and Using the
Precision Spotlight
IMPORTANT!
READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
INTRODUCTION
The Marinco Precision spotlight uses a super bright 100 Watt, replaceable H3 Halogen bulb
that produces a rich yet intense beam that can illuminate objects up to 1,000ft away. It is
IP56 Weatherproof rated with a double o-ring sealed base, UV weather resistant housing
and fully enclosed tilt function driven by quiet motors that can withstand extreme temperatures (5°F to 113°F or -15°C to 45°C). It has been designed and tested to withstand the
harsh marine environments including high humidity, salt water spray, shock, and vibration.
Innovative construction allows for upside down mounting and reverse motion programming.
Precision circuitry allows for remarkable aiming and tracking with two speed choices.
The Precision remotes have glow in the dark buttons and include one touch Automatic
Sweep and SOS options. The wireless remotes transmit a signal up too 200ft (60m). While
the spotlight comes with a wireless bridge remote there are two more optional remotes:
a wireless handheld remote w/lanyard (SPRL-1) and a hard wired bridge mount remote
(SPRL-3).
PACKAGE INCLUDES:
• Spotlightwith12Voltbulbinstalled
• Additional24Voltbulb**
• Mountingkit(nofastenersincluded)
• WirelessBridgeRemote
• Instructionmanual
**(modelsSPL-12W,SPL-12B,SPL-12Conly)
MODELS: SPL-12W, SPL-12B, SPL-12C
MAR_TL_029_1011_Precision_Spotlight_ Manual_6x9_Ins.indd 1-2 11/3/11 11:15 AM
Precision Spotlight Instructions Precision Spotlight Instructions
Required for Installation:
• Four(4)No.10stainlesssteelpanheadscrewsforspotlightbracket(Length and type of
screws to be determined by mounting surface)
• Two(2)No.6stainlesssteelpanheadscrews(Length and type of screws to be
determined by mounting surface)
• Two(2)#16AWGbuttwireconnectors
WARNING: IF THE APPLICATION IS 24 VOLTS. THE 12 VOLT BULB WILL NEED TO BE
REPLACED WITH THE 24 VOLT BULB. TO REPLACE THE BULB REFER TO THE BULB
REPLACEMENT SECTION. (PAGES 4-5).
Failure to use the appropriate bulb wattage will damage the spotlight.
WARNING: BEFORE OPERATION REMOVE BLUE FILM FROM LENS. FAILURE TO
REMOVE FILM WILL DAMAGE THE SPOTLIGHT.
Mounting and wiring of the Precision Spotlight
1. Select a flat surface to mount the spotlight. Make sure there are no obstructions around
the spotlight that could interfere with the rotation. (template included with light). Be sure you
will have wiring access to the underside of the chosen location and that drilling holes will
not damage existing wiring or structures. Avoid locations where lines, anchors and sails
might entangle or damage the light.
2. Refer to the template for mounting and wire hole location.
3. While installing the mounting bracket make sure that the securing screw is opposite the
direction that the light will be facing. Mark the mounting holes and center wire hole.
Be sure that there is at least a 6"(145mm) radius of clearance from the center hole.
See dotted line on figure 1.
4. Drill hole sizes appropriate for the type of screws or bolts being used. Note: the maximum
bracket whole sizes are No. 10 screws.
5. Drill the appropriate hole size to accommodate the wires. This will depend on the type of
wire being used.
6. The spotlight requires 12 or 24 volt power supplied through appropriate gauge wire.
(Note: If the wired bridge remote version is used than 2 additional wires will need to
be routed from the remote to the spotlight.)
WARNING: CORRECT WIRE SIZE FOR THE RUN AND CIRCUIT BREAKER PROTECTION
NEEDS TO BE SELECTED BASED ON ABYC STANDARDS. FAILURE TO FOLLOW ABYC
STANDARDS MIGHT LEAD TO SEVERE INJURY, DEATH OR DAMAGE TO VESSEL.
7. Mount the bracket. But first apply a small amount of non silicone sealant to where the
screws or bolts penetrate the mounting surface. (Note: mounting bracket screw
heads should not protrude more than .2” (5mm) above mounting bracket.)
8. Connect wires to spotlight using butt connectors. Red wire is positive,
Black wire is negative.
WARNING: POLARITY OF THE WIRES NEEDS TO BE CORRECT TO OPERATE THE
SPOTLIGHT! FAILURE TO WIRE CORRECTLY WILL DAMAGE THE SPOTLIGHT
SYSTEM!
9. Slide spotlight over mounting plate making sure the wires are not pinched and the two
holding tabs engage the light in the proper location. Align the external screw hole with
the screw threads on the mounting plate. This will require a degree of pressure and effort
as the mounting seal must be suitably compressed during this process. Insert securing
screw and ensure that it is fully engaged and secure.
2
7
FIGURE 1
MAR_TL_029_1011_Precision_Spotlight_ Manual_6x9_Ins.indd 3-4 11/3/11 11:15 AM
Loading...