Marcy MD-8851R User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List
Warranty

Ordering Parts

Model

MD-8851R

Retain This

Manual for

Reference

170301

OWNER'S

MANUAL

MARCY® DELUXE

CAGE & BENCH

MD-8851R

Pure-Tec Limited

www.puretecfitness.com

Tel: [phone]

Email: [e-mail]

Monday - Friday 0800 – 1700 GMT

TABLE OF CONTENTS

BEFORE YOU BEGIN..................................................................……………. 1

IMPORTANT SAFETY NOTICES.................................................................… 2

WARNING LABEL PLACEMENT……………………………………………….. 3

FREE AND TRAINING AREA…………………………………………………… 4

CAGE HARDWARE PACK….......…...........................................……………… 5

CAGE ASSEMBLY INSTRUCTIONS........................................………………. 7

EXPLODED DIAGRAM……………………………………………………………. 19
CAGE PARTS LIST………..………………………………………………………. 20

MULTI-PURPOSE BENCH HARDWARE PACK……………………………….. 21

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS..........................… 23

EXPLODED DIAGRAM……………………………………………………………. 27
MULTI-PURPOSE BENCH PARTS LIST………………………………………… 28

WARRANTY...............................................................................................…. 29

ORDERING PARTS...................................................................................….. 29

BEFORE YOU BEGIN

Thank you for selecting the MARCY® MD-8851R Deluxe Cage & Bench. For
your safety and benefit, read this manual carefully before using the machine.
As the official representative for Marcy, we are committed to providing complete
customer satisfaction. If you have any questions, or find missing or damaged
parts, we guarantee you complete satisfaction through direct assistance from our
factory. To avoid unnecessary delays, please call our Customer Solutions
Department. Monday to Friday 8am to 5pm GMT.

.

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual before
you assemble or operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

CARE AND MAINTENANCE

1. Lubricate moving parts with WD-40 or light oil periodically.

2. Inspect and tighten all parts before using the machine.

3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.

4. Maximum user’s weight: 136 kgs

5. Maximum weights on the Bar Catch: 136 kgs

6. Maximum weights on Leg Developer: 45 kgs

7. Maximum weights on Sliding Weight Post: 45 kgs

8. Cage assembled dimension: 129cm x 108cm x 213cm

9. Bench assembled dimension: 174cm x 66cm x 116cm

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. PURE-TEC LIMITED
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

.

2

WARNING LABEL PLACEMENT

.

3

FREE AND TRAINGING AREA REQUIREMENTS

.

4

CAGE HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

.

5

CAGE HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

.

6

CAGE ASSEMBLY INSTRUCTION

Tools Required for Assembling the Machine: One Adjustable Wrench and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Left Vertical Frame (#1) onto a Base Frame (#3). Secure it with two M10 x 3

1/8” Allen Bolts (#48), four Ø ¾” Washers (#55), and two M10 Aircraft Nuts (#57).
C.) Attach a Diagonal Support (#4) to the Left Vertical Frame and the Base Frame.
D.) Secure the Diagonal Support to Left Vertical Frame from top with one M10 x 2 ½” Carriage

Bolt (#45), one Ø ¾” Washer (#55), and one M10 Aircraft Nut (#57). Secure it from side

with one M10 x 2 ¾” Carriage Bolt (#44), one Ø ¾” Washer (#55), and one M10 Aircraft

Nut (#57).
E.) Secure the Diagonal Support to the Base Frame with one M10 x 1” Allen Bolt (#53) and

one Ø ¾” Washer (#55).
F.) Repeat B, C, D, and E to install the Right Vertical Frame (#2), one Base Frame, and one

Diagonal Support together.
G.) Connect the two Diagonal Supports together with a Cross Brace (#5) in the mid-span.

Secure each end of Cross Brace with two M10 x 2 ¾” Carriage Bolts (#44), one 4 ¾” x 2”

Bracket (#18), two Ø ¾” Washers (#55), and two M10 Aircraft Nuts (#57).

H.) Attach the Chin-up Bar (#6) to the Left and Right Vertical Frame. Secure each end with

two M10 x 1 5/8” Carriage Bolts (#46), two Ø ¾” Washers (#55), and two M10 Aircraft

Nuts (#57).

.

7

DIAGRAM 1

.

8