Marcy cl203, CL503 User Manual

Motion Cycle

Product Code: CL203

Escalade International Limited

Pleasant Road, Penllergaer, Swansea. SA4 9GE

Tel: [phone] Fax [phone]

www.escaladesports.co.uk

[e-mail]

16/09/2009-3

2

Contents

Important Safety Information 3
Weight Limit Capacities

Hardware Parts List 4

Pre Assembly Check List 5

Assembly Instructions 6 - 9

User Guide 10

Computer Instructions 11

Exercise Instructions 12

Fault Finding Chart 13

Exploded Diagram 14

Parts List 15

Additional Information 16
Care Maintenance

Limited Warranty 17

Supplied by

Escalade International Ltd

Pleasant Road

Penllergaer

Swansea
SA4 9GE

Tel: [phone]

Fax: [phone]

www.escaladesports.co.uk

E mail: [e-mail]

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

THIS OWNER’S MANUAL CONTAINS ASSEMBLY, OPERATION, MAINTENANCE AND

SAFETY INFORMATION. IN THE INTEREST OF SAFETY, PLEASE MAKE CERTAIN THAT

YOU READ AND UNDERSTAND ALL THE INFORMATION BELOW.

1. This cycle is intended for class H (H=Domestic) use only. It is not designed for
commercial use.

2. This machine has been tested to BS EN 957 Parts 1:2005 and Part 5:1996.

3. Read the OWNER’S OPERATION MANUAL and all accompanying literature and follow
it carefully before using your cycle.

4. Keep children and pets away from the Cycle at all times. Do not leave children
unattended in the same room with the Cycle. The Cycle is not a toy and therefore
parents and guardians should be aware of the natural tendency for children to play,
leading to situations and behaviour for which the Cycle is not intended.

5. If children are allowed to use the Cycle their physical/mental development and above all,
temperament should be taken into account. Constant supervision is therefore needed.

6. Position the Cycle on a clear levelled surface which is clear of all obstacles as not to
restrict movement whilst exercising. DO NOT use the Cycle near water or outdoors.

7. Exercise equipment has moving parts. In the interest of safety, keep others, especially
children, at a safe distance while exercising.

8. Never hold your breath while exercising. Breathing should remain at a normal rate in
conjunction with the level of exercise being performed.

9. Rest adequately between workouts. Muscle tone develops during these rest periods.
Beginners should work out twice a week and increase gradually to 4 to 5 times per
week.

10. Remove all jewellery, including rings, chains and pins before commencing exercise.

11. Always wear suitable clothing and footwear during exercise. Do not wear loose fitting
clothing that could become entangled with the moving parts of your exercise machine.

IMPORTANT!!! THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR YOUR
CYCLE IS 100KGS.

3

HARDWARE PARTS LIST

PART NO. DESCRIPTION Q’TY

11 Knob

1

15 Carriage Bolt M8*L65mm

2

16 Curve WasherΦ22

6

17 Domed Nut M8

2

18 Allen Bolt M8*15mm

8

19 Flat Washer Φ25

2

26 Screw for Handlebar

2

27 Flat Washer Φ17

2
Allen Key L6 1
Allen Wrench S13-15-19 1

Above described parts are all the parts you need to assemble this machine. Before
you start to assemble, please check the hardware packing to make sure they are
included.

4

PRE-ASSEMBLY CHECK LIST

PART NO. DESCRIPTION Q’TY

01 Main Frame 1
02 Front Stabilizer 1
03 Rear Stabilizer 1
04 Front Post 1
05 Handlebar 1
06 Computer 1
07 Seat Post 1
08 Seat 1
09 Left Pedal 1
10 Right Pedal 1

User Manual 1

Please note that some items of hardware may already be pre assembled onto your
cycle.

5

ASSEMBLY INSTRUCTION

STEP 1

(a) Attach the front stabilizer (2) to the main frame (1), and tighten using 2 carriage bolts

(15), curve washer (16) and domed nut (17).

(b) Then, attach the rear stabilizer (3) to the main frame (1), using 2 allen bolts (18), and flat

washer (19) for the bottom of rear stabilizer, then tighten 2 sets of allen bolt (18), and flat
washer (27) for each side of the rear stabilizer.

STEP 2

Take the front post (4) and connect the middle computer wire (21) with lower computer wire

(22). Release the tension knob (20) on the front post (4) then connect with the lower tension

cable (23). Please see page 7 for a detailed description of the assembly. Insert the front

post (4) into the main frame (1) and tighten using 4 allen bolt (18) and curve washer (16).

6