Marcy B80 User Manual

www.puretecfitness.com

1

B80
UPRIGHT BIKE

USER MANUAL

Distributed By:

Pure-Tec Limited

www.puretecfitness.com

www.puretecfitness.com

2

CONTENTS

Important Safety Information
Weight Limit Capacities

Hardware Parts List

Pre Assembly Check List

Assembly Instructions

Computer Instructions

Exercise Instructions

Exploded Diagram

Parts List

Additional Information

Warranty Information

3

4

5

6 - 11

12-19

20-21

22-23

24-25

26

27

www.puretecfitness.com

3

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

1. This Bike is intended for class H (H=Domestic) use only. It is not designed for commercial
use.

2. This machine has been tested to EN 957.

3. Read the OWNER’S OPERATION MANUAL and all accompanying literature and follow it
carefully before using your Bike.

4. Keep children and pets away from the Bike at all times. Do not leave children unattended
in the same room with the Bike. The Bike is not a toy and therefore parents and guardians
should be aware of the natural tendency for children to play, leading to situations and
behaviour for which the Bike is not intended.

5. If children are allowed to use the Bike their physical/mental development and above all,
temperament should be taken into account. Constant supervision is therefore needed.

6. Position the Bike on a clear levelled surface which is clear of all obstacles as not to restrict
movement whilst exercising. DO NOT use the Bike near water or outdoors.

7. Exercise equipment has moving parts. In the interest of safety, keep others, especially
children, at a safe distance while exercising.

8. Never hold your breath while exercising. Breathing should remain at a normal rate in
conjunction with the level of exercise being performed.

9. Rest adequately between workouts. Muscle tone develops during these rest periods.
Beginners should work out twice a week and increase gradually to 4 to 5 times per week.

10. Remove all jewellery, including rings, chains and pins before commencing exercise.

11. Always wear suitable clothing and footwear during exercise. Do not wear loose fitting
clothing that could become entangled with the moving parts of your exercise machine.

IMPORTANT!!! THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR YOUR
BIKE IS 120KGS.

THIS OWNER’S MANUAL CONTAINS ASSEMBLY, OPERATION, MAINTENANCE AND

SAFETY INFORMATION. IN THE INTEREST OF SAFETY, PLEASE MAKE CERTAIN

THAT YOU READ AND UNDERSTAND ALL THE INFORMATION BELOW.

www.puretecfitness.com

4

HARDWARE PACKING LIST

NO.

DESCRIPTION

DRAWING

QTY

15

Allen bolt M8*55

4

16

Curved washerΦ22

8

18

Allen bolt M8*16

4

21

T type knob

1

37

Clamp cover

1

11

Quick release knob

1

73

Spring washerФ8

4

Box Wrench

1

Allen key L6

1

www.puretecfitness.com

5

PRE-ASSEMBLY CHECK LIST

1 4 7

6

9/10

38

8

76

5

2

3 12

PART NO.

DESCRIPTION

Q’TY

1

Main frame

1

4

Front support

1

7

Seat support

1

6

Meter

1

9/10

Pedal ( L/R )

1/1

38

Front support cover

1

8

Seat 1 76

Towel holder

1

5

Handlebar

1

2

Front stabilizer

1

3

Rear stabilizer

1

12

Sliding seat cover

1

www.puretecfitness.com

6

ASSEMBLY INSTRUCTION

STEP 1

Attach the front stabilizer (2) to the front of the main frame (1), fasten with two curved
washers (16), two spring washers (73) , two allen bolts (15).
Attach the rear stabilizer (3) to the rear of the main frame (1), fasten with two curved
washers (16), two spring washers (73), two allen bolts (15).

1

15

15

73

16

73

16

2

3

www.puretecfitness.com

7

STEP 2

Connect the upper sensor wire (33) from the front support (4) to the lower sensor
wire (34).
through on the front support cover (38) on the front support (4).
Insert the front support (4) into the main frame (1) and fasten with four allen bolts
(18) and four curved washers (16).

4

16

16

18

18

33

38

34

1

www.puretecfitness.com

8

STEP 3

Attach the handlebar (5) to the front support (4) and fasten with one clamp (25), one allen
bolt (22), one clamp cover (37) and one T type knob (21).
Connect the upper sensor wire (33) to the sensor wire on the back of the meter (6).

Insert the hand pulse wire (20) through grommet (32) on front support (4) and pull it out of
front support (4), Insert the hand pulse wire (20) to the pulse hole on the back of meter (6).
Attach the meter (6) to the front support (4) and fasten with four screws (27) which are
pre-assemble on the meter (6).

6

20

33

21

5

32 25

22

37

1

www.puretecfitness.com

9

STEP 4

Attach the sliding seat cover (12) to the seat support (7) and fasten with one self-tapping
screw (39).
Attach the towel holder (76) to the seat (8) and fasten with two nut (54) and two washer (35)
which are pre-assemble on the seat (8)
Release two nuts on the back of seat (8) and attach it to the seat support (7), then fix the
seat by tightening two nuts.
Insert the seat support (7) into the main frame (1) and fasten with one quick release knob
(11) which could adjust the height to your desired position.

8

76

35

54

8

76

39

12

7

12

Nut

11

8

7

1