Page 1
Showdown
5.6 Dual Beam
Digital Fish Finder
User Manual
www.marcumtech.com
Page 2
Versa Electronics www.marcumtech.com
- 2 -
Table of Contents
About Your New Showdown Dual Beam Digital Fish Finder .............3
In Your Showdown 5.6 Dual Beam Package . . . ......................3
Getting Started ................................................4
Battery Charging ...............................................5
Some common sense safety tips ...............................5
To charge your battery ........................................5
Operating The Showdown 5.6 Dual Beam ...........................5
Showdown 5.6 Dual Beam Features ................................6
Ice-Mode .....................................................6
Other Showdown 5.6 Dual Beam Features ..........................9
Tips For Using Your Showdown 5.6 Dual Beam ......................10
Moving the Showdown Dual Beam to a new location .................11
Caring For Your Showdown 5.6 Dual Beam .........................12
Troubleshooting ..............................................12
Nothing happens after the POWER button has been pressed ........12
Unit turns on but will not read bottom ...........................13
Screen seems to be getting heavy interference, lots of “clutter” ......13
Showdown 5.6 Dual Beam Specifications ..........................13
Showdown 5.6 Dual Beam Replacement Parts ......................13
One-Year Limited Warranty .....................................14
How to Obtain Service .........................................14
Page 3
Versa Electronics www.marcumtech.com
- 3 -
About Your New Showdown Dual Beam Digital Fish Finder
Congratulations! Your new Showdown 5.6 Dual Beam Digital Fish Finder
delivers unmatched performance and is the most intuitive and easy to use
system on the market… the future of ice-fishing electronics is here! With the
Showdown 5.6 Dual Beam, you will catch more fish and have more fun. This
is due in part to the simplicity of the ShowDown’s sonar presentation, as well
as the user-friendliness of the interface. You will now spend more time actually
fishing, and less time trying to figure out how to use and interpret what your
sonar unit is showing you.
Simply turn on your Showdown 5.6 Dual Beam, and immediately begin observing the action below. The ShowDown’s Auto Depth Range feature means
there’s no switching between various depth ranges. Nor will you have to guess
at bottom or depth itself. The Showdown 5.6 Dual Beam immediately locks on
to the proper depth range, while also displaying digital depth at all times.
In addition to other standard features such as Adjustable Zoom, Sensitivity, Range, and Noise Reduction, your new Showdown 5.6 Dual Beam Also
features the exclusive “Ice Mode,” which provides seamless sonar operation
even in extremely cold conditions (down to at least -40°F). Turning this feature
on activates a heating element that keeps the internal liquid crystals moving at
super-high speed. (Typical liquid crystal sonar units often freeze and delay the
display speed under cold conditions). All these features combine into the most
precise, yet simple-to-use sonar unit on the market. Thank you for making this
purchase—you’ll be glad you did.
In Your Showdown 5.6 Dual Beam Package . . .
•Showdown5.6DualBeamsonar
•Adjustablegimbaltilt-bracket
•6-feettransducer/powercableand
200kHz-DualBeam8/20Degreetransducer
•BatteryShuttlewithretractabletransducerarm
•NeoprenesoftpackwithVelcroenclosureandinteriormeshtransducer
pocket
•Rubberstopperfortransducercable
•12-volt,9.0-ampsealedgel-cellbattery,2ampinlinefuse
•.5ampBatteryCharger
•User’sManual
•WarrantyCard
Page 4
Versa Electronics www.marcumtech.com
- 4 -
Getting Started
Your new Showdown 5.6 Dual Beam Digital Fish Finder comes completely
assembled, and nearly ready to use. Follow the simple steps below and you
will be ready to fish.
(1) Remove your Showdown 5.6 Dual Beam unit from the box. Gently remove
the interior unit from neoprene case. The Showdown 5.6 Dual Beam sonar
unit should be firmly attached to clear gimbal bracket, which should be
pre-assembled, and attached to base of battery case. Make sure the Velcro
battery strap is tight to keep battery snug in case.
(2) Make sure all wire connections are solid. Check to make sure the 2 amp
fuse is inserted into fuse holder. Be sure that the positive (RED +) spade is
connected to the positive terminal on battery, and that the negative (BLACK -)
spade is connected to the negative terminal on battery.
(3) Check unit connections. Rectangular plug should be firmly attached
to the rear of Showdown 5.6 Dual Beam unit. Do not force plug into place.
Make sure that 5-holeside is on top when making this connection. This plug
connects the ShowDown unit to the transducer and the 12-volt power source.
Insert single POWER plug from transducer cord into the single hole POWER
receptacle on the end of the wiring harness coming from the battery. This is
the power connection on your Showdown 5.6 Dual Beam sonar unit.
(4) Make sure that the round rubber stopper is securely in place on the transducer cable, and that the Velcro battery strap is tight to keep battery snug in
the battery compartment.
(5) Slide fully assembled Showdown 5.6 Dual Beam back into neoprene case.
(6) The 9 amp battery provided comes with a good charge on it and can be
taken fishing upon opening the box. Before initial use, you may want to charge
it fully if you are not going fishing immediately. To charge the battery, see
below.
(7) Route transducer cable through the adjustable transducer turning arm.
Affix rubber cable stopper at the desired depth above transducer.
(8) Place your Showdown 5.6 Dual Beam on a relatively level spot on the ice,
extend the transducer arm over ice hole, place the transducer into the water,
and turn the unit ON by pressing the POWER key.
(9) To store your ShowDown, turn power OFF, fold in transducer arm, tuck
transducer into interior mesh pocket, and fold Velcro closure over. Remember
to recharge battery after every use—this will maximize run time and battery
longevity.
Page 5
Versa Electronics www.marcumtech.com
- 5 -
Battery Charging
Your Showdown system comes with a 3-stage battery charger. This style of
charger has proven to be the most effective and easiest to use of all charging
systems available. While the rate of charge is low, a completely discharged
battery can be brought back to a full charge in as little as 12 hours. Because
this is a 3-stage charger, there is no danger of overcharging your battery.
Therefore, it is recommended that you charge your battery overnight after
each use, and once every few months during periods of non-use.
A 3-Stage charger works like this—
Stage 1 (Bulk Stage): Constant current charging at a high voltage level at
maximum amperage to minimize charge time.
Stage 2 (Absorption Stage): Current tapers off for final 10% of charge.
Stage 3 (Maintenance Stage): Lower voltage mode to prevent electrolyte loss,
keeping your battery at full charge indefinitely.
Some common sense safety tips:
For safety reasons, it is recommended that you place your system on a flat,
hard surface like cement or tile when charging it, away from any flammable
materials. While this sophisticated charging and maintenance system allows
you to leave the battery unattended without concern over damaging effects
from overcharging, it is still recommended that you avoid leaving your battery
hooked up to the charger for extended periods of time, and disconnect the
charger from the wall when not in use.
To charge your battery:
To charge your battery, first disconnect the POWER plug from the POWER
receptacle. Remove the .5-amp battery charger from packaging box, unwrap
cord, and plug into the base POWER receptacle. Plug the transformer end of
the battery charger and charge the battery for 12-hours or until the green LED
appears on battery charger.
Operating The Showdown 5.6 Dual Beam
The ShowDown’s straightforward control panel is designed to let you
concentrate on fishing. Most settings work by first activating the function
itself (ex: press SENS to trigger sensitivity adjustment), then simply pressing
the UP or DOWN keys to adjust levels.
POWER
ON— To turn your Showdown 5.6 Dual Beam POWER to ON, press and hold
POWER key for two seconds.
OFF— To turn your Showdown 5.6 Dual Beam POWER to OFF, press and
hold POWER for two seconds. Showdown 5.6 Dual Beam automatically
preserves your sonar settings the next time you activate unit.
Page 6
Versa Electronics www.marcumtech.com
- 6 -
BACKLIGHT— To turn backlight on, turn Showdown 5.6 Dual Beam POWER
ON, then press POWER key again (do not hold key down). To turn backlight
off, press POWER momentarily again (do not display hold button down).
SIMULATOR MODE— With Showdown 5.6 Dual Beam POWER OFF, enter
SIMULATOR mode by pressing and holding POWER key for 5 seconds. The
“SIMU” indicator will appear at the top-right of Showdown 5.6 Dual Beam
view-screen. To exit SIMULATOR, turn Showdown 5.6 Dual Beam POWER to
OFF, then turn unit back ON.
UP/DOWN— Pressing the UP or DOWN key lets you adjust the Sensitivity,
Range, Zoom and Noise. Trigger a function first by pressing the appropriate
function key, then move UP or DOWN.
Showdown 5.6 Dual Beam Features
ACTIVATING DUAL BEAM MODE – Your Showdown 5.6 Dual Beam transducer can be easily switched from a 20 degree cone angle (good for general
use) to an 8 degree cone angle (good for water over 40’, or any time there is a
lot of structure below you) . To switch between the narrow and wide beams –
First – Press and hold the “UP” button and then press and hold the “RANGE”
button to “activate” the Narrow Beam or the Wide Beam. When the cone
angles have been switched, an “8” or “20” will appear briefly on the bottom of
the display, indicating which cone angle you are currently using.
The approximate area of coverage with a 20 degree transducer is determined by dividing the depth by 3 (in 30 feet of water your area of coverage
is approximately 10’). The approximate area of coverage with an 8 degree
transducer is determined by dividing the depth by 7 (in 30 feet of water your
area of coverage is approximately 4.25’).
Ice-Mode
Your Showdown 5.6 sonar offers exclusive ICE Mode, a feature unique to
Versa Electronics brand sonar units, which allows for operation in the coldest
conditions. With ICE Mode active, Showdown 5.6 triggers an internal LCD
heater that keeps the liquid crystals moving at their normal super high speeds
in sub-freezing temperatures. This means that anglers no longer have to
worry about their sonar “slowing down” due to freezing liquid crystal. While
this feature is called “Ice Mode”, you may find that your Showdown performs
better under a wide variety of conditions when in “ICE” mode.
NOTE: If your Showdown 5.6 Dual Beam is left in extreme cold for an
extended time period with the POWER turned OFF, allow one to two minutes
for the Ice Mode LCD heater to warm the crystals sufficiently after the
POWER has been turned ON and ICE Mode has been activated. After the
ICE Mode LCD heater has been running for an extended period, it is perfectly
normal for the Showdown 5.6 Dual Beam power-head to feel warm.
Page 7
Versa Electronics www.marcumtech.com
- 7 -
TO INITIATE ICE MODE, simply press the UP and DOWN buttons simultaneously. You will now see the “ICE” mode indicator appear at the top of
the Showdown 5.6 Dual Beam display screen. In ICE mode, an internal LCD
heater is initiated. To exit ICE mode and return Showdown 5.6 Dual Beam to
normal operating mode, press the UP and DOWN keys simultaneously. The
ICE mode indicator will no longer show at the top of the display screen.
SENS (SENSITIVITY) — The Showdown 5.6 is a highly-sensitive sonar unit
capable of reading the tiniest of objects below. It features a 25-level Sensitivity function that adjusts either automatically or manually. By simply turning on
your Showdown, it will automatically select a level of sensitivity appropriate
for the given depth and signal strength. Ideally, the Sensitivity should be set
at the lowest level possible to still view your lure and surrounding fish, while at
the same time “tuning out” excessive clutter in the water column. Clutter can
make reading the sonar screen more difficult. Clutter can be caused by any
number of suspended items, including algae, zooplankton, tiny bubbles, and
other particles.
If you’re seeing too much clutter, simply decrease the Sensitivity level until the
clutter disappears. Conversely, if you’re not reading your lure directly below
the transducer, consider increasing the Sensitivity level.
MANUAL SENSITIVITY— While your Showdown will automatically select
an appropriate level of sensitivity, you may wish to adjust the level yourself.
To manually adjust Showdown 5.6 sensitivity press the SENS button. The
“SENS” indicator will appear at the lower left of view-screen, along with a
number and bar indicator that displays Sensitivity level (0 to 25) at the bottom
of the screen.
With the SENS indicator active, press the UP or DOWN key to increase or
decrease your sensitivity to the desired level. In most cases, you will have the
best performance with the sensitivity set between 5 and 10.
RANGE— The Showdown 5.6 Dual Beam is equipped with 6-separate depth
ranges—20, 40, 60, 80, 120, and 240-feet. Regardless of the manual depth
range setting, Showdown 5.6 Dual Beam will always display digital depth,
even if the bottom is deeper than the bottom limit of the RANGE setting
(down to 240’).
AUTO RANGE— Your Showdown 5.6 Dual Beam will automatically lock into
the depth range appropriate to the depth of the water. For instance, in 32-feet
of water, Showdown 5.6 Dual Beam will automatically lock in at the 40-foot
depth range. Auto Range allows you to simply turn on the power and begin
fishing.
MANUAL RANGE— To manually adjust the Showdown’s depth range, press
the RANGE key. This will cause the digital depth markers to flash on-and-off,
indicating that the sonar has switched from AUTO RANGE mode to MANUAL
RANGE mode.
Page 8
Versa Electronics www.marcumtech.com
- 8 -
While the display is flashing, press either the UP or DOWN key to toggle
between depth ranges—20-FT, 40-FT, 60-FT, 80-FT, 120-FT, 240-FT. Pressing
UP moves RANGE to the next shallower depth zone; DOWN moves to the
next deeper zone. To return to Auto Range, press the RANGE key, and then
press the UP key (moving Range to the next shallower setting) until the Range
passes the 20-foot range by one step. At this point, you will hear an audible
fast beep, and see a flashing “A” icon above the FEET indicator.
ZOOM— The Zoom feature allows you to focus the display on a specific
depth within the water column. This position of the ZOOM window is adjustable in one-foot increments. Zoom can focus on bottom (for detecting
bottom-hugging fish), or at any level above bottom. The Zoom window is
programmed to display 25% of the depth range (i.e. – in 100 feet of water, you
will zoom to different 25-foot segments of the water column).
The Showdown 5.6 Dual Beam sonar also offers Auto Bottom Track Zoom
that automatically zooms and locks onto the bottom 25-percent of the water
column. This is especially useful for locating bottom-hugging fish like walleyes
and perch.
MANUAL ADJUSTABLE ZOOM— To zoom the display in on a specific
segment of the water column, press the ZOOM key once. Once ZOOM is
activated, the word ZOOM will appear at the top left of the display screen.
You can now adjust ZOOM to any depth segment by simply pressing the
UP or DOWN keys—once for each ZOOM level. To ZOOM into the bottom,
simply continue pressing the DOWN key until you reach the desired level.
To disengage ZOOM (bringing the Showdown 5.6 Dual Beam back to normal
surface-to-bottom view) simply press the ZOOM button a second time. The
ZOOM indicator will no longer appear at the top left of the display.
AUTO BOTTOM TRACK ZOOM— To automatically zoom onto the bottom
25-percent of the water column, you may choose to enter Auto Bottom Track
Zoom. This is an extremely helpful feature that will always lock onto and zoom
in on the bottom, even if you have removed the transducer from one area, and
placed it into completely different depth.
To enter Auto Bottom Track Zoom, press the ZOOM key (you should see the
ZOOM icon at the top left of the screen). Press the UP key until you have
passed the shallowest depth range. At this point, you will hear an audible fast
beep, and see a flashing “A” icon at the bottom of the screen.
NOISE (Interference Rejection) — The unit’s Noise Rejection feature allows
you to use your Showdown 5.6 Dual Beam in close proximity to other sonar
units, trolling motors, and other electronic devices without experiencing
excessive signal interference. A ten (10) level Noise Rejection function allows
you to adjust to a wide range of rejection levels. If “noise interference” occurs,
increase the NOISE Rejection level until you effectively eliminate the signal
interference. To adjust the Showdown’s NOISE Rejection control, simply
press the NOISE button once. The NOISE indicator bar will appear at the
bottom of the screen, along with a number (0 to 10), which shows the NOISE
control setting.
Page 9
Versa Electronics www.marcumtech.com
- 9 -
Press the UP button to move to the next highest NOISE rejection level, or
press DOWN to move to the next lowest NOISE rejection level. As you do
so, you should notice the indicator number change. After approximately
5-seconds, the NOISE indicator bar will disappear and be replaced by the
normal operating depth display.
Other Showdown 5.6 Dual Beam Features
Backlight— Your Showdown 5.6 Dual Beam offers a warm “nightglow” backlight that actually accentuates the pixels in the display. Can be turned on or
off by briefly pressing the POWER button after unit is ON.
Neoprene Carry Bag— Protects your Showdown 5.6 Dual Beam during
storage, use and transport. Exterior Velcro flap seals out dust and moisture.
Interior Transducer Pocket— Small mesh pocket inside neoprene carrying
case. Always place your transducer in this pocket when not in use.
Adjustable Transducer Arm— Showdown 5.6 Dual Beam is equipped with
an extendable and adjustable transducer arm, which directs the transducer
over your ice fishing hole. Coupled with the round rubber transducer cable
stopper which fits over the top of the arm clip, this handy item keeps your
transducer level in the water at all times for optimal signal return. When not in
use, the arm folds up and fits snugly inside the neoprene-carrying bag.
Digital Depth— The digital depth display on the Showdown 5.6 Dual Beam
sonar provides a quick and easy way to determine depth. Digital Depth is
always displayed in the bottom-right of the view screen (unless NOISE or
SENS are being adjusted). In addition, digital depth scale indices show to the
left of the display area for quickly determining the depth of fish or your lure.
Simulator— To trigger the Showdown 5.6 Dual Beam Simulator mode, start
with unit turned OFF. Press and hold the POWER button for approximately
5-seconds. You should see the “SIMU” indicator bar appear at the top right of
the display. Simulator mode shows how bottom, a lure and fish might appear
on the unit if you were fishing in 32’ of water. It also allows you to adjust and
learn various sonar settings before you get out fishing. To turn Simulator mode
off, it is necessary to turn Showdown 5.6 Dual Beam Power OFF by holding
down the POWER button again.
Low Battery Warning— When battery power reaches very low levels,
a low battery indicator will appear and flash at the top right of the display.
An audible beep will also sound every 30 seconds. This signifies that it is
time to recharge the battery, or replace it with a fully charged spare.
WARNING: When you see and hear this warning, the Showdown 5.6 Dual
Beam may shut down within minutes.
“Last Settings” Memory— Your Showdown 5.6 Dual Beam automatically
remembers the settings you used last. So when it is turned OFF and then
ON again, your previous settings will be preserved and active.
Page 10
Versa Electronics www.marcumtech.com
- 10 -
Tips For Using Your Showdown 5.6 Dual Beam
Setting up the transducer for ice fishing: When used in conjunction with
the retractable pivoting transducer arm and rubber stopper, the Showdown’s
transducer will automatically level itself in your ice hole. To begin operation,
simply insert transducer cable into rubber stopper at desired depth. Extend
transducer arm; insert cable into open end of transducer arm, and allow the
rubber stopper to rest in the open end of the transducer arm. We recommend
setting your stopper to have the transducer down the least amount possible.
The Showdown Dual Beam puts out enough power that in most cases it is not
necessary to have your transducer down more than a few inches below the
water line to get a good reading. When the ice thickness is over two feet, it
may be necessary to have your transducer set farther down. Remember--the
less transducer cable you have out, the easier it is to pull it out of the water
when bringing in a fish, or to move to a new location.
Reading the Showdown 5.6 Dual Beam Dual Beam sonar signals: The
Showdown 5.6 Dual Beam displays the water column in its natural state
(vertically), rather than in a confusing circular configuration, such as is the
case with traditional dial flashers. On the Showdown, top is the surface, and
bottom is bottom. Bottom appears as a dark solid bar above decreasingly
solid bars below. A thicker “bottom band” indicates a harder bottom composition, such as rock, gravel or sand. A thinner band indicates a softer bottom.
Generally, a solid band that appears on the screen between the surface
and bottom indicates some form of aquatic life (game fish, baitfish, insects,
plankton, etc.), or your lure. Thicker or more solid bands imply larger objects,
such as game fish. This is due to the nature of the ShowDown’s sonar signals.
Stronger or denser objects return a stronger signal back to the transducer
than smaller objects.
At the same time, even a large fish may not return a strong signal until it
swims directly beneath your transducer. This is because the transducer emits
a cone-shaped signal that increases in diameter as the signal travels deeper.
Therefore, not only will a fish appear to grow in size as it travels beneath the
transducer (the signal has become stronger), but it will also appear to be
swimming from deeper water to shallower water, even though this may not be
the case at all. A fish that’s swimming at 25 feet may not display at 25-feet
until it passes directly beneath the sonar transducer. That’s simply because
the sonar signal travels further to return an echo from a fish that’s off to the
side than it does for a fish that’s directly below.
How do I “see” my lure? The best way to find your lure on the Showdown
5.6 Dual Beam screen is to simply drop your lure down to bottom, then reel it
up about a foot. You should see a single solid band appear above bottom to
signify your lure. If you do not see this, adjust the sonar Sensitivity by pressing
the SENS button and UP/DOWN keys (see SENSITVITY). Adjust sensitivity
until you can make out your lure even as you reel it up toward the surface, or
jig it up and down. .Do not increase sensitivity too much, however, as doing
this may cause your Showdown 5.6 Dual Beam to display excess “clutter”
that makes following your lure and nearby fish more difficult.
Page 11
Versa Electronics www.marcumtech.com
- 11 -
Battery life and sonar run-time: A fully charged 12-volt, 9.0-amp battery will
provide up to 30-hours of use. NOTE: In ICE mode, run time will be decreased
slightly due to the power requirements of the LCD heater. To assure long
battery life and peak sonar performance, we recommend charging the battery
after every use.
Will the Showdown 5.6 Dual Beam read through the ice? Yes. This is a
great way to save time while looking for a particular spot or depth. To receive
a sonar signal directly through the ice (without drilling a hole), first clear off
any snow that may be covering ice. Make sure that ice in the area is relatively
“clear” ice without excessive bubbles or frost pockets, which can deflect
sonar signals. Pour about a cup of water on the spot, and immediately rest
the transducer on the standing water on the ice. If you still don’t have a signal,
pour additional water under the transducer. If the surface of the ice is rough
or filled with air bubbles, drilling a 1” deep hole in the ice before checking the
depth may be necessary.
Moving the Showdown Dual Beam to a new location
Being mobile is one of the keys to being successful on the ice. Whenever you
move from one spot to another, it is tempting to leave your transducer hanging
on the transducer arm. This is likely to lead to failure of the transducer arm,
and can cause damage to the transducer itself if it is allowed to drag on the
ice. Always fold the transducer arm in, and stow the transducer inside the
pack when you are moving. Keeping the amount of transducer cord you have
out at a minimum will make transporting your Showdown easier. Similarly,
you may need to quickly remove your transducer from the hole when about to
land a fish. We have actually seen anglers in a panic actually grab the shuttle
itself and toss the entire unit to the side. This is no way to treat any piece of
electronics; a much better approach is to simply lift the transducer out of your
way by the cord, and the shuttle itself can be gently pushed aside.
Page 12
Versa Electronics www.marcumtech.com
- 12 -
Caring For Your Showdown 5.6 Dual Beam
To keep your Showdown 5.6 Dual Beam running at optimal performance, we
recommend the following:
Stow your Showdown 5.6 Dual Beam properly when not in use. Turn sonar
power off, and disconnect Power plug from back of unit. If possible, gently
wipe excess water or moisture from the Showdown 5.6 Dual Beam screen and
transducer arm with a soft cloth.
Slide the adjustable transducer arm back into the housing, and stow transducer into the interior pocket. Close and secure soft case door with Velcro
enclosure. Store in cool (above 30°F, below 85°F), dry location whenever
possible.
Recharge battery after every use. Even if you only used your Showdown for a
short time, getting in the habit of regularly charging your battery will maximize
the life of your battery, and will ensure that your Showdown will be ready to go
for your next outing. During prolonged storage periods, recharge the battery
every few months. These steps will maximize the life of your battery.
Clean your Showdown 5.6 Dual Beam periodically. Using a mild dishwashing
soap and a soft cloth, gently clean the power head and view screen. DO NOT
use window cleaner or alcohol-based cleaning products—they may damage
LCD screen and void your warranty.
Troubleshooting
Nothing happens (screen fails to display) after the POWER button has been
pressed:
•Batterynotconnected.Properlyconnectthebattery;redtored(positive),
black to black (negative)
•Batterynotsufcientlycharged.(SeeBatteryCharging)
•PowercordmaynotbeconnectedtoShowdown5.6DualBeamorshuttle
power port. Check connections and try POWER again
•Checkwiringonpowercable.MakesureallconnectionsbetweenShowdown5.6DualBeam/transducer/batteryaresolid.
•Checktheconditionofthe2-ampinlinefuse(locatedontheRED(+)wire
coming off the battery). The wire in a 2 amp fuse is very fine, and it can take
a very close look to determine if it is still intact. If there are any beaks in the
wire or discoloration in the clear plastic, replace the fuse. It is acceptable to
replace the 2 amp fuse with a 3 amp fuse. Using a fuse larger than a 3 amp
may damage your Showdown.
Page 13
Versa Electronics www.marcumtech.com
- 13 -
Unit turns on but will not read bottom:
•Transducermaynotbeproperlyleveledorconnected.Checkcableconnections. Make sure the bottom of the transducer has a clear path to the
bottom, and is not obstructed by any solid objects.
•Checktoseeifyouhaveadjustedthemanualdepthrange.Ifrangeisset
shallower than the depth of the water, bottom will not display in the viewing
area. Adjust range to be just slightly deeper than bottom.
Screen seems to be getting heavy interference, with lots of “clutter”:
•AdjusttheShowdown5.6DualBeamsensitivity.Often,decreasingtheunit’s
sensitivity will keep unwanted signals from appearing on screen.
•Youmightbereceivinginterferencefromadjacentelectronicdevices,such
as a competing sonar unit. Activate and adjust the ShowDown’s Noise
Rejection until you find a level that clears up most or all of the interference
(see NOISE section).
Showdown 5.6 Dual Beam Specifications
Current Draw: 400 mA maximum Transducer Frequency: 200kHz Transducer
Angle:DualBeam8/20°TransmitPower:1000-wattstrueRMS/8000watts
peak-to-peak power Ping Rate: 40 pings per second max Sonar Resolution:
0.46” (in 20’, 40’ and 60’ ranges) Sensitivity Control: 25-level Noise Rejection
Control: 10-level anti-interference Range Control: 6 depth ranges—20’, 40’,
60’, 80’, 120’, 240’ Zoom Control: Zooms in to 25% of the water column, or in
one foot increments as specified by user. Ice Mode: Activates LCD heater, and
boosts gain. Digital Depth Display: Yes. Display Grayscale: 4-level Grayscale
Showdown 5.6 Dual Beam Replacement Parts
The rigors of ice fishing can take a toll on equipment. Replacement parts that
have become lost or damaged can be easily ordered, go to showdownfishfinder.com, or you can call us at (888) 778-1208.
Parts list
Transducer
Turning arm
Straight arm
Pack
Gimball
Stopper (2-pack)
2-Amp fuse (2-pack)
Manual
12 V 9 amp battery
Page 14
Versa Electronics www.marcumtech.com
- 14 -
One-Year Limited Warranty
Versa Electronics warrants this product to be free from defects in materials and workmanship for one year from the date of purchase. This warranty
applies to customers who properly fill out and return the warranty card
included with this manual. Failure to complete and return the warranty card
voids the warranty. Versa Electronics will, at its sole discretion and without
charging the customer, repair or replace any components that fail in normal
use. Failures due to abuse, misuse, or unauthorized alteration, modification
or repair are not covered. Cut cables and submerged power-heads are not
covered.Brokencableand/orpower-headconnectorswillincuraservice
repair charge. The battery is not covered by this warranty. The warranty is
valid only for the original owner who purchases the unit from an authorized
Versa Electronics dealer. Products purchased from on-line auction sites are
not considered under warranty.
How to Obtain Service
We want our products to provide you with a pleasant on-the-water experience. That means maximum customer satisfaction. If you have a problem with
your Showdown 5.6 Dual Beam unit please contact Versa Electronics toll free
number at 888-778-1208 or send email to service@versae.com for a Return
Authorization number (RA#). No service returns will be accepted without this
return authorization number, which must be clearly marked on the outside of
the package. Versa Electronics retains the exclusive right to repair or replace
the unit at its discretion.
The customer is responsible for shipping costs associated with returning the
unit to Versa Electronics. Versa Electronics will pay for shipping the repaired
unit back to the customer while it is still under one-year warranty. All out-of
warranty services will be charged a fee for service and shipping which must
be paid in advance. After obtaining a Return Authorization number, the unit
should be securely packed and shipped “pre-paid freight” and insured to
Versa Electronics. It is the consumers’ full responsibility to track their products
sent out in the mail or other forms of delivery service. Versa Electronics will
not be liable for lost packages sent out in the mail. Unless specified otherwise,
do not include battery or other accessories when returning the unit for repair.
Versa Electronics will not be responsible for lost or damaged accessories.
Please allow a minimum of 10 business days prior to calling on the status of
your repair.
Versa Electronics
3943 Quebec Avenue N.
Minneapolis, MN 55427
RA# _________________
Note: The RA number must
be clearly marked on the
outside of the package
Page 15
Versa Electronics www.marcumtech.com
- 15 -
Other Marcum Products
Here are some other great systems from Marcum. These items can be
purchased from one of our many fine retailers, or direct from us at marcum-
tech.com
LX5 The LX-5 incorporates the latest in sonar technology, featuring a patented
flexible zoom that can be set anywhere between surface and bottom, a patent
pending TrueColor display, 2500 watts of peak-to-peak power, patented signal
interference rejection, Superfine Line Technology, and target separation down
to3/4inch.
LX7 The LX-7 Digital Sonar takes DNA from other fine Marcum sonars –you
might say it was “bred” for excellence. Because the LX-7 is digital, we can
pack it full of more features than have ever been found in an ice sonar before.
With an 8” customizable dashboard display, superior target separation,
12-level interference rejection, dual-beam transducer, expandable zoom, and
much, much more, the LX7 is the perfect combination of macro features and
micro precision.
Showdown Troller The new Showdown Troller Digital Fish Finder is a palm-
sized sonar device with full size performance. For use in either ice-fishing or
open water situations…quickly “troll” from hole to hole while ice-fishing or
shoot through your canoe or kayak in order to find fish and the correct depth.
As a scouting tool it has ne equal; the ultimate in portability is matched to
ShowDown’s proven Crystal-Quick® vertical display. The sonar instantly locks
on to bottom, and clearly displays the location of fish and your lure, anywhere
in the water column.
VS825SD The VS825sd offers several technologies that are the first of their
kind, making this system the most technologically advanced underwater
viewing system available.
Using new technology such as an 8” Solar Intelligent- H2D display will deliver
the sharpest, most vivid display, even in direct sunlight; Color Kill technology
allows you to switch between a Color or Black and White image on demand,
while maintaining crisp screen resolution; On-Screen displays of Camera
Direction, Depth, Temp and Battery Voltage take all of the guess work out of
your camera position so your new VS825sd can be used to hunt for underwater treasures, locate the “spot on the spot”, observe fish in their natural habitat
or learn how fish react to your lure or bait presentation. The applications are
endless, and it’s never been easier or more fun to view.
Page 16
www.marcumtech.com
MarCum User Manuals are available for download from
www.marcumtech.com.
Loading...