Page 1
Showdown 5.6
Digital Fish Finder
User Manual
www.marcumtech.com
Page 2
Versa Electronics www.marcumtech.com
- 2 -
Table of Contents
About Your New Showdown Digital Fish Finder . . . . . . . . . . . . . . . . . . . . . . .3
In Your Showdown 5.6 Package ...................................3
Getting Started ................................................4
Battery Charging ...............................................5
Some common sense safety tips: ...............................5
To charge your battery: ........................................5
Operating The Showdown 5.6 .....................................6
Showdown 5.6 Features .........................................6
Other Showdown 5.6 Features ....................................9
Tips For Using Your Showdown 5.6 ...............................10
Moving the Showdown to a new location ...........................11
Caring For Your Showdown 5.6 ..................................11
Troubleshooting ..............................................12
Nothing happens after the POWER button has been pressed: ........12
Unit turns on but will not read bottom ...........................12
Screen seems to be getting heavy interference, lots of “clutter”: ......12
Showdown 5.6 Specifications ...................................13
One-Year Limited Warranty .....................................13
How to Obtain Service ........................................13
Showdown 5.6 Replacement Parts ...............................14
Page 3
Versa Electronics www.marcumtech.com
- 3 -
About Your New Showdown Digital Fish Finder
Congratulations! Your new Showdown 5.6 Digital Fish Finder delivers
unmatched system performance and offers the most intuitive and easy to use
system on the market… the future of ice-fishing electronics is here! As a result
of your purchase, we believe you will catch more fish and have more fun. This
is due in part to the simplicity of ShowDown’s sonar presentation, as well as the
user-friendliness of the interface. You will now spend more time actually fishing,
less time trying to figure out how to use and interpret what your sonar unit is
showing you.
Simply turn your Showdown 5.6 on to immediately begin observing the action
below. The ShowDown’s Auto Depth Range feature means there’s no switching
between various depth ranges. Nor will you have to guess at bottom or depth
itself. The Showdown 5.6 immediately locks on to the proper depth range, while
also displaying digital depth at all times.
In addition to other standard features such as Adjustable Zoom, Sensitivity,
Range, and Noise Reduction, your new Showdown 5.6 also features the
exclusive “Ice Mode,” which provides seamless sonar operation even in
extremely cold conditions (down to at least -40°F). Turning this feature on
activates a heating element that keeps the internal liquid crystals moving at
super-high speed. (Typical liquid crystal sonar units often freeze and delay the
display speed under cold conditions).
All these features combine into the most precise, yet simple-to-use sonar unit
on the market. Thank you for making this purchase—you’ll be glad you did.
In Your Showdown 5.6 Package
•Showdown5.6sonar
•Adjustablegimbaltilt-bracket
•6-feettransducer/powercableand
200 kHz – 20 degree transducer
•BatteryShuttlewithretractabletransducerarm
•Neoprenesoftpackwithhookandloopclosureandinteriormesh
transducer pocket
•Rubberstopperfortransducercable
•12-volt,9.0-ampsealedgel-cellbattery,2ampinlinefuse
•1-ampBatteryCharger
•User’sManual
•WarrantyCard
Page 4
Versa Electronics www.marcumtech.com
- 4 -
Getting Started
Your new Showdown 5.6 Digital Fish Finder comes completely assembled,
and nearly ready to use. Follow the simple steps below and you will be ready
to fish.
(1) Remove the Showdown 5.6 from the box. Gently remove interior unit from
neoprene case. Your Showdown should be firmly attached to clear gimbal
bracket, which should be pre-assembled, and attached to the top of battery
case.
(2) Make sure all wire connections are solid. Check to make sure the 2 amp
fuse is inserted into fuse holder. Check that the positive (RED +) spade is
connected to the positive terminal on battery, and that the negative (BLACK -)
spade is connected to the negative terminal on battery.
(3) Check unit connections. Rectangular female plug should be firmly attached
to the rear of your Showdown. Do not force the plug into place. Make
sure that the 5-hole side is on top when making this connection. This plug
connects the ShowDown unit to the transducer and the 12-volt power source.
Insert single power plug from the transducer cord into the single hole power
receptacle on the end of the wiring harness coming from the battery. This is
the power connection on your Showdown 5.6 sonar unit.
(4) Make sure that the round rubber stopper is securely in place on the transducer cable, and that the hook and loop battery strap is tight to keep battery
snug in the battery compartment.
(5) Slide fully assembled Showdown 5.6 back into the neoprene case.
(6) The 9 amp battery provided comes with a good charge on it and can be
taken fishing upon opening the box. Before initial use, you may want to charge
it fully if you are not going fishing immediately. To charge the battery, see
below.
(7) Route transducer cable through the adjustable transducer turning arm.
Affix rubber cable stopper at the desired depth above transducer.
(8) Place your Showdown 5.6 on a relatively level spot on the ice, extend the
transducer arm over ice hole, place the transducer into the water, and turn the
unit ON by pressing the POWER key.
(9) To store your ShowDown, turn power OFF, fold in transducer arm, tuck
transducer into interior mesh pocket, and fold hook and loop closure over.
Remember to recharge battery after every use—this will maximize run time
and battery longevity.
Page 5
Versa Electronics www.marcumtech.com
- 5 -
Battery Charging
Your Marcum system comes with a 3-stage battery charger. This style of
charger has proven to be the most effective and easiest to use of all charging
systems available. While the rate of charge is low, a completely discharged
battery can be brought back to a full charge in as little as 12 hours. Because
this is a 3-stage charger, there is no danger of overcharging your battery.
When properly cared for, a sealed lead acid battery will last for at least a
couple of years. Batteries are made to be used, and they need to be used to
make the most of them. The most important thing you can do is to promptly
recharge your battery after each use. Not charging your battery immediately
after use is the number one thing that leads to battery failure. When you get
home from a trip, put your battery on charge right away, and leave it there
overnight, or for around 8-12 hours. We often talk to people who hesitate
to charge their battery after each use for fear that the battery will develop
a “memory” and this will lead to a shortened run time—THIS IS FALSE!!!
ALWAYS CHARGE YOUR BATTERY AFTER EVERY USE!!! Be sure to use the
charger that came with your system, or a similar one that is between .5 amp
and 1 amp. Using a larger charger, like you would use on a car, truck, RV, or
boat is likely to cause damage to the battery. There is really very little danger
of overcharging your battery with a low amp charger, and most chargers automatically go into “maintenance mode” once a full charge has been achieved.
A 3-Stage charger works like this—
Stage 1 (Bulk Stage): Constant current charging at a high voltage level at
maximum amperage to minimize charge time.
Stage 2 (Absorption Stage): Current tapers off for final 10% of charge.
Stage 3 (Maintenance Stage): Lower voltage mode to prevent electrolyte loss,
keeping your battery at full charge indefinitely.
Some common sense safety tips:
For safety reasons, it is recommended that you place your system on a flat,
hard surface like cement or tile when charging it, away from any flammable
materials. Be sure to disconnect the charger from the wall when not in use,
and avoid leaving your battery hooked up to the charger for extended periods
of time.
To charge your battery:
Your battery has a wiring harness attached to it that has “piggyback” terminals
on it, enabling you to keep the power cord from the unit attached to the
battery at all times, as well as having the wiring harness with receptacle for
your charger attached at all times. To charge, simply couple the end of the
charger with the end of the wiring harness. It is normal for a green light to
appear on the charger at this time. Once connected, plug the transformer
end of the charger into a 110 volt AC wall outlet. You will see a red LED light
appear on the charger at this time. When your battery is fully charged, this
red light will change to green. Depending on the condition of your battery, this
process can take up to 20 hours to complete. At this time, you can disconnect
the charger from the battery and wall outlet. However, no harm will come to
your battery if you leave it attached to the charger.
Page 6
Versa Electronics www.marcumtech.com
- 6 -
If you need to remove the battery, unplug the two battery terminals from the
battery. Remove the hook and loop strap that is holding the battery in place
and lift the battery out. To replace the battery, place a new battery of similar
specifications into the battery compartment and secure it with the hook and
loop strap and re-connect the positive and negative terminals.
Operating The Showdown 5.6
The ShowDown’s straightforward control panel is designed to let you concentrate on fishing. Most settings work by first activating the function itself (ex:
press SENS to trigger sensitivity adjustment), then simply pressing the UP or
DOWN keys to adjust levels.
POWER
ON— To turn your Showdown 5.6 POWER to ON, press and hold the POWER
key for two seconds.
OFF— To turn your Showdown 5.6 POWER to OFF, press and hold POWER
for two seconds. Your Showdown 5.6 automatically preserves your sonar
settings the next time you activate unit.
BACKLIGHT— To turn the backlight on, turn your POWER ON, then press
POWER key again (do not hold key down). To turn backlight OFF, press
Power momentarily again (do not hold down the power button).
SIMULATOR mode— With Showdown 5.6 POWER OFF, enter SIMULATOR mode by pressing and holding POWER key for 5 seconds. The “SIMU”
indicator will appear at the top-right of Showdown 5.6 view-screen. To exit
SIMULATOR, turn Showdown 5.6 POWER to OFF, then turn unit back ON.
UP/DOWN— Pressing the UP or DOWN key lets you adjust the Sensitivity,
Range, Zoom and Noise. Trigger a function first by pressing the appropriate
function key, then move UP or DOWN.
Showdown 5.6 Features
ICE-MODE
Your Showdown 5.6 sonar offers exclusive ICE MODE, a feature unique to
Versa Electronics brand sonar units, which allows for operation in the coldest
conditions. With ICE MODE active, Showdown 5.6 triggers an internal LCD
heater that keeps the liquid crystals moving at their normal super high speeds
in sub-freezing temperatures. This means that anglers no longer have to worry
about their sonar “slowing down” due to freezing liquid crystal. While this
feature is called “ICE MODE”, you may find that your Showdown performs
better under a wide variety of conditions when in “ICE MODE”.
NOTE: If your Showdown 5.6 is left in extreme cold for an extended time
period with the POWER turned OFF, allow one to two minutes for the Ice
Mode LCD heater to warm the crystals sufficiently after the POWER has
been turned ON and ICE Mode has been activated. After the ICE Mode LCD
heater has been running for an extended period, it is perfectly normal for the
Showdown 5.6 power-head to feel warm.
Page 7
Versa Electronics www.marcumtech.com
- 7 -
TO INITIATE ICE MODE, simply press the UP and DOWN buttons simultaneously. You will now see the “ICE” mode indicator appear at the top of
the Showdown 5.6 Dual Beam display screen. In ICE mode, an internal LCD
heater is initiated. To exit ICE MODE and return Showdown 5.6 to normal
operating mode, press the UP and DOWN keys simultaneously. The ICE
MODE indicator will no longer show at the top of the display screen.
SENS (SENSITIVITY) — The Showdown 5.6 is a highly-sensitive sonar unit
capable of reading the tiniest of solid objects below. It features a 25-level
Sensitivity function that adjusts either automatically or manually. By simply
turning on your Showdown, it will automatically select a level of sensitivity
appropriate for the given depth and signal strength. Ideally, the Sensitivity
should be set at the lowest level possible to still view your lure and surrounding fish, while at the same time “tuning out” excessive clutter in the water
column. Clutter can make reading the sonar screen more difficult. Clutter can
be caused by any number of suspended items, including algae, zooplankton,
tiny bubbles, and other particles.
If you’re seeing too much clutter, simply decrease the Sensitivity level until the
clutter disappears. Conversely, if you’re not reading your lure directly below
the transducer, consider increasing the Sensitivity level.
MANUAL SENSITIVITY— While your Showdown will automatically select an
appropriate level of sensitivity, you may wish to adjust the level yourself. To
manually adjust Showdown 5.6 SENSITIVITY press the SENS button. The
“SENS” indicator will appear at the lower left of view-screen, along with a
number and bar indicator that displays Sensitivity level (0 to 25) at the bottom
of the screen.
With the SENS indicator active, press the UP or DOWN key to increase or
decrease your SENSITIVITY to the desired level. In most cases, you will
have the best performance with the Sensitivity set between 5 and 10.
RANGE— The Showdown 5.6 is equipped with 6 separate depth ranges—20,
40, 60, 80, 120, and 240-feet. Regardless of the manual depth range setting,
Showdown 5.6 will always display digital depth, even if the bottom is deeper
than the bottom limit of the RANGE setting, (down to 240’).
AUTO RANGE— In Auto Range mode, Showdown 5.6 will automatically lock
into the depth range appropriate to the depth of the water. For instance, in
32-feet of water, Showdown 5.6 will automatically lock in at the 40-foot depth
range. Auto Range allows you to simply turn on the power and begin fishing.
MANUAL RANGE— To manually adjust the Showdown’s depth range, press
the RANGE key. This will cause the digital depth markers to flash on-and-off,
indicating that the sonar has switched from AUTO RANGE mode to MANUAL
RANGE mode.
While the display is flashing, press either the UP or DOWN key to toggle
between depth ranges—20-FT, 40-FT, 60-FT, 80-FT, 120-FT, 240-FT. Pressing
UP moves RANGE to the next shallower depth zone; DOWN moves to the
next deeper zone.
Page 8
Versa Electronics www.marcumtech.com
- 8 -
To return to AUTO RANGE, press the RANGE key, and then press the UP
key (moving Range to the next shallower setting) until the Range passes the
20-foot range by one step. At this point, you will hear an audible fast beep,
and see a flashing “A” icon above the FEET indicator.
ZOOM— The Zoom feature allows you to focus the display on a specific
depth within the water column. The position of the ZOOM window is adjustable in one-foot increments. Zoom can focus on bottom (for detecting
bottom-hugging fish), or at any level above bottom. The Zoom window is
programmed to display 25% of the depth range (i.e. – in 100 feet of water, you
will zoom to different 25-foot segments of the water column).
MANUAL ADJUSTABLE ZOOM— To zoom the display in on a specific
segment of the water column, press the ZOOM key once. Once ZOOM is
activated, the word ZOOM will appear at the top left of the display screen.
You can now adjust ZOOM to any depth segment by simply pressing the
UP or DOWN keys—once for each ZOOM level. To ZOOM into the bottom,
simply continue pressing the DOWN key until you reach the desired level.
To disengage ZOOM (bringing the Showdown 5.6 back to normal surfaceto-bottom view) simply press the ZOOM button a second time. The ZOOM
indicator will no longer appear at the top left of the display.
AUTO BOTTOM TRACK ZOOM— The Showdown 5.6 sonar also offers Auto
Bottom Track Zoom that automatically zooms and locks onto the bottom
25-percent of the water column. This is especially useful for locating bottom
hugging fish like walleyes and perch. To automatically zoom onto the bottom
25-percent of the water column, you may choose to enter Auto Bottom Track
Zoom. This is an extremely helpful feature that will always lock onto and zoom
in on the bottom, even if you have removed the transducer from one area, and
placed it into completely different depth.
To enter Auto Bottom Track Zoom, press the ZOOM key (you should see the
ZOOM icon at the top left of the screen). Press the UP key until you have
passed the shallowest depth range. At this point, you will hear an audible fast
beep, and see a flashing “A” icon at the bottom of the screen.
NOISE (Interference Rejection) — The unit’s Noise Rejection feature allows
you to use your Showdown 5.6 in close proximity to other sonar units, trolling
motors, and other electronic devices without experiencing excessive signal
interference. A ten (10) level Noise Rejection function allows you to adjust to
a wide range of rejection levels. If “noise interference” occurs, increase the
Noise Rejection level until you effectively eliminate the signal interference. To
adjust the ShowDown’s NOISE Rejection control, simply press the NOISE
button once. The NOISE indicator bar will appear at the bottom of the screen,
along with a number (0 to 10), which shows the NOISE control setting. Press
the UP button to move to the next highest NOISE rejection level, or press
DOWN to move to the next lowest NOISE rejection level. As you do so, you
should notice the indicator number change. After approximately 5-seconds,
the NOISE indicator bar will disappear and be replaced by the normal operating depth display.
Page 9
Versa Electronics www.marcumtech.com
- 9 -
Other Showdown 5.6 Features
Backlight— Your Showdown 5.6 offers a warm “nightglow” backlight that
actually accentuates the pixels in the display. Can be turned on or off by
briefly pressing the POWER button after unit is ON.
Neoprene Carry Bag— Protects your Showdown 5.6 during storage, use and
transport. Exterior hook and loop flap seals out dust and moisture.
Interior Transducer Pocket— Small mesh pocket inside neoprene carrying
case. Always place your transducer in this pocket when not in use.
Adjustable Transducer Arm— Your Showdown 5.6 is equipped with an
extendable and adjustable transducer arm which directs the transducer over
your ice fishing hole. Coupled with the round rubber transducer cable stopper
which fits over the top of the arm clip, this handy item keeps your transducer
level in the water at all times for optimal signal return. When not in use, the
arm folds up, and fits snugly inside the neoprene carrying bag.
Digital Depth— The digital depth display on the Showdown 5.6sonar
provides a quick and easy way to determine depth. Digital Depth is always
displayed in the bottom-right of the view screen (unless NOISE or SENS are
being adjusted). In addition, digital depth scale indices show to the left of the
display area for quickly determining the depth of fish or your lure.
Simulator— To trigger the Showdown 5.6 Simulator mode, start with unit
turned OFF. Press and hold the POWER button for approximately 5-seconds.
You should see the “SIMU” indicator bar appear at the top right of the display.
Simulator mode shows how bottom, a lure and fish might appear on the
unit if you were fishing in 32’ of water. It also allows you to adjust and learn
various sonar settings before you get out fishing. To turn Simulator mode off,
it is necessary to turn your Showdown 5.6 power OFF by holding down the
POWER button again.
Low Battery Warning— When battery power reaches very low levels, a
low battery indicator will appear and flash at the top right of the display. An
audible beep will also sound every 30 seconds. This signifies that it is time
to recharge the battery, or replace it with a fully charged spare. WARNING:
When you see and hear this warning, the Showdown 5.6 may shut down
within minutes.
“Last Settings” Memory— Your Showdown 5.6 automatically remembers
the settings you used last. So when it is turned OFF and then ON again, your
previous settings will be preserved and active.
Page 10
Versa Electronics www.marcumtech.com
- 10 -
Tips For Using Your Showdown 5.6
Setting up the transducer for ice-fishing: When used in conjunction with
the retractable pivoting transducer arm and rubber stopper, the Showdown’s
transducer will automatically level itself in your ice hole. To begin operation,
simply insert transducer cable into rubber stopper at desired depth. Extend
transducer arm; insert cable into open end of transducer arm, and allow the
rubber stopper to rest in the open end of the transducer arm. We recommend
setting your stopper to have the transducer down the least amount possible.
The Showdown Dual Beam puts out enough power that in most cases it is not
necessary to have your transducer down more than a few inches below the
water line to get a good reading. When the ice thickness is over two feet, it
may be necessary to have your transducer set farther down. Remember--the
less transducer cable you have out, the easier it is to pull it out of the water
when bringing in a fish, or to move to a new location.
Reading the Showdown 5.6 sonar signals: The Showdown 5.6 displays
the water column in its natural state (vertically), rather than in a confusing
circular configuration, such as is the case with traditional dial flashers. On the
ShowDown, top is the surface, and bottom is bottom. Bottom appears as a
dark solid bar above decreasingly solid bars below. A thicker “bottom band”
indicates a harder bottom composition, such as rock, gravel or sand. A thinner
band indicates a softer bottom.
Generally, a solid band that appears on the screen between the surface
and bottom indicates some form of aquatic life (gamefish, baitfish, insects,
plankton, etc.), or your lure. Thicker or more solid bands imply larger objects,
such as gamefish. This is due to the nature of the ShowDown’s sonar signals.
Stronger or denser objects return a stronger signal back to the transducer
than smaller objects.
At the same time, even a large fish may not return a strong signal until it
swims directly beneath your transducer. This is because the transducer emits
a cone-shaped signal that increases in diameter as the signal travels deeper.
Therefore, not only will a fish appear to grow in size as it travels beneath the
transducer (the signal has become stronger), but it will also appear to be
swimming from deeper water to shallower water, even though this may not be
the case at all. A fish that’s swimming at 25 feet may not display at 25-feet
until it passes directly beneath the sonar transducer. That’s simply because
the sonar signal travels further to return an echo from a fish that’s off to the
side than it does for a fish that’s directly below.
How do I “see” my lure? The best way to find your lure on the Showdown 5.6
screen is to simply drop your lure down to bottom, then reel it up about a foot.
You should see a single solid band appear above bottom to signify your lure. If
you do not see this, adjust the sonar Sensitivity by pressing the SENS button
and the UP/DOWN keys (see SENSITVITY). Adjust sensitivity until you can
make out your lure even as you reel it up toward the surface, or jig it up and
down. Do not increase sensitivity too much, however, as doing this may cause
your Showdown 5.6 to display excess “clutter” that makes following your lure
and nearby fish more difficult.
Page 11
Versa Electronics www.marcumtech.com
- 11 -
Battery life and sonar run-time: Generally, a fully charged 12-volt, 9.0-amp
battery (included) will provide up to 30-hours of use. NOTE: In ICE mode, run
time will be decreased slightly, due to the power requirements of the LCD
heater. To assure long battery life, and peak sonar performance, we recommend charging the battery after every use.
Will the Showdown 5.6 read through the ice? Yes. This is a great way to
save time while looking for a particular spot or depth. To receive a sonar signal
directly through the ice (without drilling a hole), first clear off any snow that may
be covering ice. Make sure that ice in the area is relatively “clear” ice without
excessive bubbles or frost pockets, which can deflect sonar signals. Pour
about a cup of water on the spot, and immediately rest the transducer on the
standing water on the ice. If you still don’t have a signal, pour additional water
under the transducer. If the surface of the ice is rough or filled with air bubbles,
drilling a 1” deep hole in the ice before checking the depth may be necessary.
Moving the Showdown to a new location
Being mobile is one of the keys to being successful on the ice. Whenever you
move from one spot to another, it is tempting to leave your transducer hanging
on the transducer arm. This is likely to lead to failure of the transducer arm,
and can cause damage to the transducer itself if it is allowed to drag on the
ice. Always fold the transducer arm in, and stow the transducer inside the
pack when you are moving. Keeping the amount of transducer cord you have
out at a minimum will make transporting your Showdown easier. Similarly, you
may need to quickly remove your transducer from the hole when about to land
a fish. We have actually seen anglers in a panic actually grab the shuttle itself
and toss the entire unit to the side. This is no way to treat any piece of electronics; a much better approach is to simply lift the transducer out of your way by
the cord, and the shuttle itself can be gently pushed aside.
Caring For Your Showdown 5.6
To keep your Showdown 5.6 running at optimal performance, we recommend
the following:
Stow your Showdown 5.6 properly when not in use. Turn sonar power off, and
disconnect Power plug from back of unit. If possible, gently wipe excess water
or moisture from the Showdown 5.6 screen and transducer arm with a soft
cloth. Should your Showdown system become wet, it is unlikely that any harm
will come to it, but make sure to get the entire system completely dried out as
soon as possible.
Slide the adjustable transducer arm back into the housing, and stow transducer into the interior pocket. Close and secure soft case door with hook and
loop enclosure. Store in cool (above 30°F, below 85°F), dry location whenever
possible.
Recharge your battery after every use. Even if you only used your Showdown
for a short time, getting in the habit of regularly charging your battery will maximize the life of your battery. During prolonged storage periods, recharge the
battery every few months. These steps will maximize the life of your battery.
Page 12
Versa Electronics www.marcumtech.com
- 12 -
Clean your Showdown 5.6 periodically. Using a mild dishwashing soap and a
soft cloth, gently clean the power head and view screen. DO NOT use window
cleaner or alcohol-based cleaning products—they may damage LCD screen
and void your warranty.
Troubleshooting
Nothing happens (screen fails to display) after the POWER button has been
pressed:
•Batterynotconnected.Properlyconnectthebattery;redtored(positive),
black to black (negative)
•Batterynotsufcientlycharged.(SeeBatteryCharging)
•PowercordmaynotbeconnectedtoShowdown5.6orshuttlepowerport.
Check connections and try POWER again
•Checkwiringonpowercable.MakesureallconnectionsbetweenShowdown5.6/transducer/batteryaresolid.
•Checktheconditionofthe2-ampinlinefuse(locatedontheRED(+)wire
coming off the battery). The wire in a 2 amp fuse is very fine, and it can take
a very close look to determine if it is still intact. If there are any beaks in the
wire or discoloration in the clear plastic, replace the fuse. It is acceptable to
replace the 2 amp fuse with a 3 amp fuse. Using a fuse larger than a 3 amp
may damage your Showdown.
Unit turns on but will not read bottom:
•Transducermaynotbeproperlyleveledorconnected.Checkcableconnections. Make sure the bottom of the transducer has a clear path to the
bottom, and is not obstructed by any solid objects.
•Checktoseeifyouhaveadjustedthemanualdepthrange.Ifrangeisset
shallower than the depth of the water, bottom will not display in the viewing
area. Adjust range to be just slightly deeper than bottom.
Screen seems to be getting heavy interference, with lots of “clutter”:
•AdjusttheShowdown5.6sensitivity.Often,decreasingtheunit’ssensitivity
will keep unwanted signals from appearing on screen.
•Youmightbereceivinginterferencefromadjacentelectronicdevices,such
as a competing sonar unit. Activate and adjust the ShowDown’s Noise
Rejection until you find a level that clears up most or all of the interference
(see NOISE section).
Page 13
Versa Electronics www.marcumtech.com
- 13 -
Showdown 5.6 Specifications
Current Draw: 400 mA maximum Transducer Frequency: 200kHz Transducer
Angle:20°TransmitPower:1000-wattstrueRMS/8000wattspeak-to-
peak power Ping Rate: 40 pings per second max Sonar Resolution: 0.46”
(in 20’, 40’ and 60’ ranges) Sensitivity Control: 25-level Noise Rejection
Control: 10-level anti-interference Range Control: 6 depth ranges—20’, 40’,
60’, 80’, 120’, 240’ Zoom Control: Zooms in to 25% of the water column, or in
one foot increments as specified by user. Ice Mode: Activates LCD heater, and
boosts gain. Digital Depth Display: Yes. Display Grayscale: 4-level Grayscale.
One-Year Limited Warranty
Versa Electronics warrants this product to be free from defects in materials and workmanship for one year from the date of purchase. This warranty
applies to customers who properly fill out and return the warranty card
included with this manual. Failure to complete and return the warranty card
voids the warranty. Versa Electronics will, at its sole discretion and without
charging the customer, repair or replace any components that fail in normal
use. Failures due to abuse, misuse, or unauthorized alteration, modification
or repair are not covered. Cut cables and submerged power-heads are not
covered.Brokencableand/orpower-headconnectorswillincuraservice
repair charge. The battery is not covered by this warranty. The warranty is
valid only for the original owner who purchases the unit from an authorized
Versa Electronics dealer. Products purchased from on-line auction sites are
not considered under warranty.
How to Obtain Service
We want our products to provide you with a pleasant on-the-water experience. That means maximum customer satisfaction. If you have a problem
with your Showdown 5.6, please visit us at marcumtech.com, contact Versa
Electronics toll free number at 888-778-1208, or send an email for a Return
Authorization number (RA#). No service returns will be accepted without this
return authorization number, which must be clearly marked on the outside of
the package. Versa Electronics retains the exclusive right to repair or replace
the unit at its discretion. The customer is responsible for shipping costs
associated with returning the unit to Versa Electronics. Versa Electronics will
pay for shipping the repaired unit back to the customer while it is still under
warranty. All out-of warranty services will be charged a fee for service and
shipping which must be paid in advance. After obtaining a Return Authorization number, the unit should be securely packed and shipped “pre-paid
freight” and insured to Versa Electronics. It is the consumers’ full responsibility
to track their products sent out in the mail or other forms of delivery service.
Versa Electronics will not be liable for lost packages sent out in the mail.
Unless specified otherwise, do not send the battery or other accessories when
returning the unit for repair. Versa Electronics will not be responsible for lost or
damaged accessories. Please allow a minimum of 10 business days prior to
calling on the status of your repair.
Versa Electronics
3943 Quebec Avenue N.
Minneapolis, MN 55427
RA# _________________
Note: The RA number must
be clearly marked on the
outside of the package
Page 14
Versa Electronics www.marcumtech.com
- 14 -
Showdown 5.6 Replacement Parts
The rigors of ice fishing can take a toll on equipment. Replacement parts
that have become lost or damaged can be easily ordered, go to
marcumtech.com, or you can call us at (888) 778-1208.
Parts list
Transducer
Turning arm
Straight arm
Pack
Gimball
Stopper (2-pack)
2-Amp fuse (2-pack)
Manual
12 V 9 amp battery
Page 15
Versa Electronics www.marcumtech.com
- 15 -
OTHER MARCUM PRODUCTS
Here are some other great systems from Marcum. These items can be purchased from one of our many fine retailers, or direct from us at marcumtech.com
LX5
The LX-5 incorporates the latest in sonar technology, featuring a patented
flexible zoom that can be set anywhere between surface and bottom, a patent
pending TrueColor display, 2500 watts of peak-to-peak power, patented signal
interference rejection, Superfine Line Technology, and target separation down
to3/4inch.
LX7
The LX-7 Digital Sonar takes DNA from other fine Marcum sonars –you might
say it was “bred” for excellence. Because the LX-7 is digital, we can pack it full
of more features than have ever been found in an ice sonar before. With an 8”
customizable dashboard display, superior target separation, 12-level interference rejection, dual-beam transducer, expandable zoom, and much, much
more, the LX7 is the perfect combination of macro features and micro precision.
Showdown Troller
The new Showdown Troller Digital Fish Finder is a palm-sized sonar device with
full size performance. For use in either ice-fishing or open water situations…
quickly “troll” from hole to hole while ice-fishing or shoot through your canoe
or kayak in order to find fish and the correct depth. As a scouting tool it has ne
equal; the ultimate in portability is matched to ShowDown’s proven CrystalQuick® vertical display. The sonar instantly locks on to bottom, and clearly
displays the location of fish and your lure, anywhere in the water column.
VS825SD
The VS825sd offers several technologies that are the first of their kind, making
this system the most technologically advanced underwater viewing system
available.
Using new technology such as an 8” Solar Intelligent- H2D display will deliver
the sharpest, most vivid display, even in direct sunlight; Color Kill technology
allows you to switch between a Color or Black and White image on demand,
while maintaining crisp screen resolution; On-Screen displays of Camera Direction, Depth, Temp and Battery Voltage take all of the guess work out of your
camera position so your new VS825sd can be used to hunt for underwater treasures, locate the “spot on the spot”, observe fish in their natural habitat or learn
how fish react to your lure or bait presentation. The applications are endless,
and it’s never been easier or more fun to view.
Page 16
www.marcumtech.com
MarCum User Manuals are available for download from
www.marcumtech.com.
Loading...