Marco Beverage Systems filtro Instructions Manual

1900076 REV.1 Page 1 of 4

OPERATING AND MAINTANANCE INSTRUCTIONS

FILTRO

Auto-Fill Jug, Flask & Mini-Flask Versions

- P/N: (Jug) 1000617 ; (Flask) 1000618;

- (

Jug - Dual Hot plate) 1000619; (Mini-flask) 1000622

INTRODUCTION

The information provided in this manual is intended to assist in the installation and
maintenance of the Auto-Fill Filtro Filter coffee Brewer. Please read the instructions
carefully to prevent accidents and ensure an efficient installation.
This manual is not a substitute for any safety instructions or technical data affixed to the
machine or its packaging. All information in this manual is current at the time of
publication and is subject to change without notice.
Only technicians or authorised service providers should carry out maintenance of these
machines.
The company accepts no responsibility for any damage or injury caused by incorrect or
unreasonable installation and operation.

SAFETY INSTRUCTIONS

· Read and keep these instructions.

· To protect against electric shock do not immerse mains cord in water or other

liquid.

· To prevent chafing of the cable, do not let the mains cord hang over the edge of a

table or counter; or touch hot surfaces.

· Do not operate any product with a damaged cord, plugs, or after the machine

malfunctions or has been damaged in any manner. If the supply cord is damaged,
it must be replaced by the manufacturer or approved service agent in order to
avoid a hazard.

· Switch off at the mains (unplug or disconnect from outlet). Allow to cool before

removing components.

· The use of non-approved spares and/or accessories may cause damage and/or

injuries.

· Do not use outdoors.

· Do not use the product for anything other than its intended use.

· Keep the outside of the coffee maker clean and dry at all times.

DURING OPERATION

! Allow time for all the coffee to drain from the filter bowl before removing.
! Protect the controls against grease and dirt.
! Never use warm or hot water to fill the machine.
! Risk of scalding. Beware of removing the filter basket/jug/flask when the

b

rewer is in operation. ALL users of this machine should be trained and should

b

e aware that the machine dispenses very hot beverages.

! Do not place an empty glass jug on a hotplate when it is switched on except

i

mmediately before brewing.

1900076 REV.1 Page 2 of 4

TECHNICAL DETAILS

Model

Auto-Fill Jug

1

000617

Auto-Fill Flask

1

000618

Supply voltage

230V

230V

Frequency

50Hz

50Hz

Power

2400W

2200W

Dimensions

220x385x460

[

WxDxH] mm

220x385x615

[

WxDxH] mm

Empty Weight

6.8kg

7.8kg

Capacity (per hr)

18L

18L

Brew time

5 min

6.5 min

Brew capacity

1.8L

2.2L

INSTALLATION

ELECTRICAL

· Electrical specification: 230Vac. 50Hz.

· This machine must be connected to a fused 13A single-phase power supply.

· This machine is provided with a 3-pin plug and must be connected to an earthed

supply.

PLUMBING

· Mains water pressure required (limits): 5-50psi (35-345kPa)

· Fit a stop Valve on a cold water line and attach a 3/4" BSP male fitting, (e.g. 3/4" x

1/2" 311 or washing machine type stop valve).

· Connect straight tailpiece of the inlet hose to the stop valve fitting. Make sure that

the pre-attached sealing washer is fitted.

· Turn on the water to flush any impurities, dust etc from the inlet hose and water

pipe. Allow several gallons through.

· Connect right-angled tailpiece of the hose to the inlet valve of the boiler (again

3/4" BSP). Make sure the sealing washer is fitted here also.

· Turn on water and check for leaks.

LOCATION

· Position the brewer at buffet height on a firm level base that can bear the weight

of the machine when it is filled.

· Position the brewer level and in such a way that it cannot cause any damage if it

leaks.

· Position the brewer within 1.5 metres from a suitable power socket and mains

water supply.