Marco FILTRO, FILTRO 1000615, FILTRO 1000616 Service Manual

Service Manual 1000615 Filtro Jug MF 1000616 Filtro Flask MF 02-05-06 Page 1 of 9

FILTRO

Manual-Fill Jug & Flask Version

- P/N: (Jug) 1000615 ; (Flask) 1000616

SERVICE MANUAL

Marco Beverage Systems Ltd.

63d Heather Road,

Sandyford Industrial Estate,

Dublin 18,

Republic of Ireland

Ireland Tel: [phone]

Ireland Fax: [phone]

UK Tel: [phone]

UK Fax: [phone]

Service Manual 1000615 Filtro Jug MF 1000616 Filtro Flask MF 02-05-06 Page 2 of 9

INTRODUCTION

The information provided in this manual is intended to assist in the installation and maintenance and service
of the Manual-Fill versions of the Filtro Filter coffee Brewer. Please read the instructions carefully to prevent
accidents and ensure an efficient installation.

This manual is not a substitute for any safety instructions or technical data affixed to the machine or its
packaging. All information in this manual is current at the time of publication and is subject to change
without notice.

Only technicians or authorised service providers should carry out maintenance of these machines.

The company accepts no responsibility for any damage or injury caused by incorrect or unreasonable
installation and operation.

SAFETY INSTRUCTIONS

 Read and keep these instructions.
 To protect against electric shock do not immerse mains cord in water or other liquid.
 To prevent chafing of the cable, do not let the mains cord hang over the edge of a table or counter; or

touch hot surfaces.

 Do not operate any product with a damaged cord, plugs, or after the machine malfunctions or has

been damaged in any manner. If the supply cord is damaged, it must be replaced by the manufacturer
or approved service agent in order to avoid a hazard.

 Switch off at the mains (unplug or disconnect from outlet). Allow to cool before removing

components.

 The use of non-approved spares and/or accessories may cause damage and/or injuries.
 Do not use outdoors.
 Do not use the product for anything other than its intended use.
 Keep the outside of the coffee maker clean and dry at all times.

Service Manual 1000615 Filtro Jug MF 1000616 Filtro Flask MF 02-05-06 Page 3 of 9

TECHNICAL DETAILS

Model

Manual-Fill Jug

1000615

Manual-Fill Flask

1000616

Supply voltage

230V

230V

Frequency

50Hz

50Hz

Power

2300W

2100W

Dimensions

220x385x460 [WxDxH]

mm

220x385x615 [WxDxH]

mm

Empty Weight

6.1kg

7.1kg

Capacity (per hr)

18L

18L

Brew time

5 min

6.5 min

Brew capacity max

1.8L

2.2L

INSTALLATION

ELECTRICAL

 Electrical specification: 230Vac. 50Hz.
 This machine must be connected to a fused 13A single-phase power supply.
 This machine is provided with a 3-pin plug and must be connected to an earthed supply.

LOCATION

 Position the brewer at buffet height on a firm level base that can bear the weight of the machine

when it is filled.

 Position the brewer level and in such a way that it cannot cause any damage if it leaks.
 Position the brewer within 1.5 metres from a suitable power socket.

OPERATION

 Allow time for all the coffee to drain from the filter bowl before removing.
 Protect the controls against grease and dirt.
 Never use warm or hot water to fill the machine.
 Risk of scalding. Beware of removing the filter basket/jug/flask when the brewer is in operation.

ALL users of this machine should be trained and should be aware that the machine dispenses very
hot beverages.

 Do not place an empty glass jug on a hotplate when it is switched on except immediately before

brewing.

PRIMING

The coffee machine needs to be primed with water prior to being turned on and its first operation; an amount
of water will always remain in the machine.

 Insert an empty filter basket into the machine and place an empty jug/flask on the lower hotplate (or

base in the case of the flask version)

 Pour a jug (1.8l/2.2l) of water into the tank (cold water reservoir).
 Plug the machine into the power supply and switch on the power button. The switch indicator and

‘Brewing’ light will illuminate and the buzzer will sound for 1sec. The boiler will heat up and water
will start to flow through the machine.

 At the end of the process the ‘Brew Ready’ light will illuminate and the buzzer will sound. Only half of

the water will have transferred to the jug/flask and the remainder will stay in the machine.