Marantz SR4001, SR5001 User Guide

Model SR4001/SR5001 User Guide

AV Surround Receiver

CAUTION

IMPORTANT SAFETY

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁ cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, speciﬁ es that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

NOTE:

Changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.

1. Read Instructions – All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ve n tilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization – This product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other). This plug will ﬁ t into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to ﬁ t, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

AC POLARIZED PLUG

13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Protective Attachment Plug – The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug.

15. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1.

16. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

17. Powe r Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

18. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of ﬁ re or electric shock.

19. Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁ re or electric shock. Never spill liquid of any kind on the product.

20. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualiﬁ ed service personnel.

21. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualiﬁ ed service personnel under the following conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have

fallen into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁ ed technician to restore the product to its normal operation.

e. If the product has been dropped or damaged

in any way, and

f. When the product exhibits a distinct change

in performance this indicates a need for service.

FIGURE 1

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

This Class B digital apparatus complies with Canadian ICES-003.

22. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in ﬁ re, electric shock, or other hazards.

23. Saf e ty Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

24. Wall or Ce iling Mounting – The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

25. Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including ampliﬁ ers) that produce heat.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

TABLE OF CONTENTS INTRODUCTION

INTRODUCTION .....................................1

PRECAUTIONS .......................................1

DESCRIPTION ........................................2

FEATURES .............................................. 3

ACCESSORIES ....................................... 3

FRONT PANEL ........................................4

SR4001 ................................................................................. 4

SR5001 ................................................................................. 4

FL DISPLAY .......................................................................... 6

REAR PANEL ..........................................7

SR4001 ................................................................................. 7

SR5001 ................................................................................. 7

REMOTE CONTROL OPERATION ........9

FUNCTION AND OPERATION ........................................... 9

OPERATION OF REMOTE CONTROL UNIT .................. 11

GENERAL INFORMATION OF RC5001SR TO

SR4001/SR5001 ................................................................ 12

CONTROLLING MARANTZ COMPONENTS ..................13

BASIC OPERATION .......................................................... 15

CONNECTIONS ....................................17

SPEAKER PLACEMENT ...................................................17

CONNECTING SPEAKERS .............................................. 17

CONNECTING AUDIO COMPONENTS .......................... 18

CONNECTING VIDEO COMPONENTS ..........................19

ADVANCED CONNECTING .............................................20

CONNECTING THE REMOTE CONTROL JACKS ......... 20

CONNECTING THE ANTENNA TERMINALS .................. 21

XM RADIO OVERVIEW (SR5001 only) ............................ 22

CONNECTING THE XM ANTENNA .................................22

CONNECTING FOR THE

MULTI ROOM (SR5001 only) ............................................23

SETUP ...................................................25

ON SCREEN DISPLAY MENU SYSTEM .........................25

1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND

COMPONENT VIDEO INPUT) .......................................... 26

2 SPEAKER SETUP ......................................................... 26

3 PREFERENCE ..............................................................27

4 SURROUND ..................................................................28

5 PL II (PRO LOGIC II) MUSIC PARAMETER ............... 28

6 CS II (CIRCLE SURROUND II) PARAMETER ............ 28

7 7.1 CH INPUT LEVEL ....................................................29

8 MULTI ROOM (SR5001 only) ........................................29

SIMPLE SETUP ....................................30

BASIC OPERATION (PLAYBACK) ...... 31

SELECTING AN INPUT SOURCE ....................................31

VIDEO CONVERT .............................................................31

SELECTING THE SURROUND MODE ............................ 32

ADJUSTING THE MAIN VOLUME ................................... 32

ADJUSTING THE TONE (BASS & TREBLE) CONTROL

.... 32

TEMPORARILY TURNING OFF THE SOUND ...................32

USING THE SLEEP TIMER ..............................................32

NIGHT MODE ...................................................................32

SURROUND MODE .............................. 33

OTHER FUNCTION ..............................36

TV AUTO ON/OFF FUNCTION .........................................36

ATTENUATION TO ANALOG INPUT SIGNAL ...................36

LISTENING THROUGH HEADPHONES ........................ 36

DOLBY HEADPHONE MODE ........................................... 36

VIDEO ON/OFF ................................................................36

DISPLAY MODE ................................................................36

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT .................................................... 37

RECORDING AN ANALOG SOURCE ..............................37

HT-EQ ................................................................................37

7.1 CH INPUT ....................................................................37

AUX2 INPUT ......................................................................38

LIP.SYNC (SR5001 only) ...................................................38

BASIC OPERATION (TUNER) .............38

LISTENING TO THE TUNER ............................................38

PRESET MEMORY ...........................................................39

LISTENING TO XM SATELLITE RADIO ........................... 41

SEARCH MODE ................................................................42

PRESET MEMORY ...........................................................44

TROUBLESHOOTING .......................................................45

MULTI ROOM SYSTEM

(SR5001 only) ..................................46

MULTI ROOM PLAYBACK USING THE

MULTI ROOM OUT TERMINALS ..................................... 46

MULTI ROOM PLAYBACK USING THE

MULTI SPEAKER TERMINALS ........................................ 46

SURROUND SPEAKER B SYSTEM

(SR4001 only) ..................................47

ANOTHER ROOM PLAYBACK USING THE

S (SURROUND) SPEAKER B TERMINALS .................... 47

TROUBLESHOOTING ..........................48

TECHNICAL SPECIFICATIONS ..........49

DIMENSIONS .......................................49

SETUP CODES ........................................I

Thank you for purchasing the Marantz SR4001/ SR5001 Surround receiver. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the SR4001/SR5001. As there are a number of connection and conﬁ guration options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V specialist dealer.

This user guide covers the SR4001 and SR5001, though the SR4001 is given for the title. Explanations of features belonging only to the SR5001 are indicated as “SR5001 only”.

XM Satellite Radio Ready

The XM name and related logos are registered trademarks of XM Satellite Radio Inc.

PRECAUTIONS

DO NOT LOCATE IN THE FOLLOWING PLACES

To ensure long-lasting use, do not locate the SR4001/ SR5001 where it is:

• Exposed to direct sunlight.

• Near sources of heat such as heaters.

•

In highly humid or poorly ventilated environments.

• Dusty.

• Subjected to mechanical vibrations.

• On wobbly, inclined or otherwise unstable surfaces.

• In locations such as in cramped audio racks where radiated heat is blocked. To ensure proper heat radiation, ensure the below clearance from walls and other equipment.

8 ins.(0.2 m)

AV SURROUND RECEIVER SR5001AV SURROUND RECEIVER SR5001

INPUT SELECTORINPUT SELECTOR

SIMPLESIMPLE

PUREPURE

SURROUNDSURROUND

MULTI

SETUPSETUP

DIRECTDIRECT

MODEMODE

MULTI

SPEAKER

STANDBY

AUTOAUTO

HT-EQHT-EQ

MENUMENU

PHONES

POWER ON/OFF

VOLUMEVOLUME

READY

8 ins.(0.2 m)8 ins.(0.2 m)

UPUP

DOWNDOWN

MEMORYMEMORY

DISPLAYDISPLAY

CLEARCLEAR

ATTATT

MUTEMUTE

ENTERENTER

T-MODET-MODE

EXITEXIT

BAND

AUX 1 INPUTAUX 1 INPUT

DIGITALDIGITAL

RRLLVIDEOVIDEO

S-VIDEOS-VIDEO

AUDIOAUDIO

8 ins.(0.2 m)

ENGLISH

DESCRIPTION

DTS was introduced in 1994 to provide 5.1 channels of discrete digital audio into home theater systems. DTS brings you premium quality discrete multichannel digital sound to both movies and music. DTS is a multichannel sound system designed to create full range digital sound reproduction. The no compromise DTS digital process sets the standard of quality for cinema sound by delivering an exact copy of the studio master recordings to neighborhood and home theaters. Now, every moviegoer can hear the sound exactly as the moviemaker intended. DTS can be enjoyed in the home for either movies or music on of DVD’s, LD’s, and CD’s.

“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.

The advantages of discrete multichannel systems over matrix are well known. But even in homes equipped for discrete multichannel, there remains a need for high-quality matrix decoding. This is because of the large library of matrix surround motion pictures available on disc and on VHS tape; and analog television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from twochannel matrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, bandlimited surround it can be disappointing to users accustomed to discrete multichannel.

Neo:6 offers several important improvements as follow,

• Neo:6 provides up to six full-band channels of matrix decoding from stereo matrix material. Users with 6.1 and 5.1 systems will derive six and ﬁ ve separate channels, respectively, corresponding to the standard home-theater speaker layouts.

Neo:6 technology allows various sound elements

• within a channel or channels to be steered separately, and in a way which follows naturally from the original presentation.

•

Neo:6 offers a music mode to expand stereo nonmatrix recordings into the ﬁ ve- or six-channel layout, in a way which does not diminish the subtlety and integrity of the original stereo recording.

DTS-ES Extended Surround is a new multichannel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTSES Extended Surround greatly improves the 360degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999. In addition to the 5.1 surround channels (FL, FR, C, SL, SR and LFE), DTS-ES Extended Surround also offers the SB (Surround Back) channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal formats with different surround signal recording methods, as DTSES Discrete 6.1 and DTS-ES Matrix 6.1.

“DTS”, “DTS-ES” and “Neo:6” are trademarks of Digital Theater Systems, Inc.

The stereo CD is a 16-bit medium with sampling at

44.1 kHz. Professional audio has been 20- or 24bit for some time, and there is increasing interest in higher sampling rates both for recording and for delivery into the home. Greater bit depths provide extended dynamic range. Higher sampling rates allow wider frequency response and the use of antialias and reconstruction ﬁ lters with more favorable aural characteristics.

DTS 96/24 allows for 5.1channel sound tracks to be encoded at a rate of 96kHz/24bits on DVD-Video titles. When DVD-video appeared, it became possible to deliver 24-bit, 96 kHz audio into the home, but only in two channels, and with serious limitations on picture. This capability has had little use. DVD-audio allows 96/24 in six channels, but a new player is needed, and only analog outputs are provided, necessitating the use of the D/A converters and analog electronics provided in the player.

DTS 96/24 offers the following:

1. Sound quality transparent to the original 96/24 master.

Full backward compatibility with all existing

2. decoders. (Existing decoders will output a 48 kHz signal)

3. No new player required: DTS 96/24 can be carried on DVD-video, or in the video zone of DVD-audio, accessible to all DVD players.

4. 96/24 5.1-channel sound with full-quality fullmotion video, for music programs and motion picture soundtracks on DVD-video.

“DTS” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.

Dolby Digital identiﬁ es the use of Dolby Digital audio coding for such consumer formats as DVD and DTV. As with ﬁ lm sound, Dolby Digital can provide up to ﬁ ve full-range channels for left, center, and right screen channels, independent left and right surround channels, and a sixth (“.1”) channel for low-frequency effects.

Dolby Surround Pro Logic II is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround program material; provides a convincing three-dimensional soundﬁ eld on conventional stereo music recordings; and is ideally suited to bring the surround experience to automotive sound. While conventional surround programming is fully compatible with Dolby Surround Pro Logic II decoders, soundtracks will be able to be encoded speciﬁ cally to take full advantage of Pro Logic II playback, including separate left and right surround channels. (Such material is also compatible with conventional Pro Logic decoders.)

Dolby Digital EX creates six full-bandwidth output channels from 5.1-channel sources. This is done using a matrix decoder that derives three surround channels from the two in the original recording. For best results, Dolby Digital EX should be used with movies soundtracks recorded with Dolby Digital Surround EX.

About Dolby Pro Logic IIx

Dolby Pro Logic II x technology delivers a natural and immersing 7.1-channel listening experience to the home theater environment. A product of Dolby’s expertise in surround sound and matrix decoding technologies, Dolby Pro Logic II x is a complete surround sound solution that maximizes the entertainment experience from stereo as well as

5.1-channel encoded sources.

Dolby Pro Logic II x is fully compatible with Dolby Surround Pro Logic technology and can optimally decode the thousands of commercially available Dolby Surround encoded video cassettes and television programs with enhanced depth and spatiality. It can also process any high-quality stereo or Advanced Resolution 5.1-channel music content into a seamless 6.1- or 7.1-channel listening experience.

The Dolby Headphone technology provides a surround sound listening experience over headphones. When listening to multichannel content such as DVD movies over headphones, the listening experience is fundamentally different than listening to speakers. Since the headphone speaker drivers are covering the pinna of the ear, the listening experience differs greatly from traditional speaker playback. Dolby utilizes patented headphone perspective curves to solve this problem and provides a non-fatiguing, immersive, home theater listening experience. Dolby Headphone also delivers exceptional 3D audio from stereo material.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX”, and the doubleD symbol are trademarks of Dolby Laboratories.

Circle Surround II (CS-II ) is a powerful and versatile multichannel technology. CS-II is designed to enable up to 6.1 multichannel surround sound playback from mono, stereo, CS encoded sources and other matrix encoded sources. In all cases the decoder extends it into 6 channels of surround audio and a LFE/subwoofer signal. The CS-II decoder creates a listening environment that places the listener “inside” music performances and dramatically improves both hi-fi audio conventional surround-encoded video material. CS-II provides composite stereo rear channels to greatly improve separation and image positioning – adding a heightened sense of realism to both audio and A/V productions.

CS-II is packed with other useful feature like dialog clarity (SRS Dialog) for movies and cinema-like bass enrichment (TruBass). CS-II can enable the dialog to become clearer and more discernable in movies and it enables the bass frequencies contained in the original programming to more closely achieve low frequencies – overcoming the low frequency limitations of the speakers by full octave.

Circle Surround II , Dialog Clarity, TruBass, SRS and

symbol are trademarks of SRS Labs, Inc. Circle Surround II , Dialog Clarity and TruBass technology are incorporated under license from SRS Labs, Inc.

HDCD® (High Deﬁ nition Compatible Digital ®) is a patented process for delivering on Compact Disc the full richness and details of the original microphone feed. HDCD encoded CDs sound better because they are encoded with 20-bits of real musical information as compared to 16-bits for all other CDs. HDCD overcomes the limitation of the 16-bit CD format by using a sophisticated system to encode the additional four bits onto the CD while remaining completely compatible with the CD format. When listening to HDCD recordings, you hear more dynamic range, a focused 3-D sound stage, and extremely natural vocal and musical timbre. With HDCD, you get the body, depth and emotion of the original performance not a ﬂ at, digital imitation.

HDCD system manufactured under license from Microsoft. This product is covered by one or more of the following: In the United States 5,479,168 5,638,074 5,640,161 5,808,574 5,838,274 5,854,600 5,864,311 5,872,531 and in Australia 669,114 with other patents pending.

HDMI, the and High-Deﬁ nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

FEATURES

The SR4001/SR5001 incorporates the latest generation of digital surround sound decoding technology such as Dolby Digital EX, Dolby Digital, DTS-ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby Pro-Logic II x (Movie, Music and Game), Circle Surround II (Cinema and Music). In addition, Marantz has focused on the future. By utilizing pre-out jacks, 7.1 direct inputs and a RS-232C communication port (SR5001 only), the SR4001/SR5001 is tomorrow’s technology, today!

The SR4001/SR5001 features a fully discrete 7 channel ampliﬁ er section capable of delivering 80 watts (SR4001)/90 watts (SR5001) of high-current amplification, for continuously clean and stable power into each of the 7 channels. It employs a massive EI power transformer in combination with oversized ﬁ lter capacitors. This design conﬁ guration is capable of a clear and powerful reproduction of the most demanding action movie soundtracks and full range (multichannel) music discs. Through its ability to generate very high output voltages, the SR4001/ SR5001 can easily drive the most demanding speakers with optimum results.

The SR4001/SR5001 incorporates the most advanced Digital Signal Processing circuitry, along with a Crystal each of the 7 channels. Independent power supply circuits are incorporated for the FL display, audio and video sections for maximum separation, clarity and dynamic range. Together with hand-selected customized components, all elements work in harmony to recreate the emotion, exactly as the artist had intended.

The SR4001/SR5001 is designed and engineered with extensive feedback from custom installation experts, dealers and consumers. It features multiroom/multisource, a RS-232C communication port (SR5001 only), heavy duty speaker binding posts and an extensive array of both analog and digital inputs / outputs. With 6 assignable digital inputs (including Front Aux), 3 assingnable component inputs (SR5001), 5 assignable digital input (SR4001), Super Audio CD Multi Channel (7.1 channel) direct inputs video convert system and OSD output versatility is taken to a stunning new level. Furthermore, the SR4001/SR5001 can output the OSD information through the Y/C (S-video) and composite video outputs.

192 kHz/24 bit D/A converter in

An easy-to-use universal remote control allows full access to all of the operating functions and can be used for system operation as well.

This unit has Simple Setup function for easy setup. You can setup all speaker settings by just selecting your room size and the number of your speakers with Simple Setup function. You can also setup customized settings just like conventional AV ampliﬁ ers.

• Dolby Digital EX, Dolby Digital , DTS ES (Discrete 6.1, Matrix 6.1, Neo: 6)

• Dolby Headphone 2

• Dolby Pro Logic IIx (Movie, Music, Game)

• Circle Surround II (Movie, Music, Mono)

• HDCD decording

• 7 × 80 Watts (8 Ohm) (SR4001)/7 × 90 Watts (8 Ohm) (SR5001), Discrete Ampliﬁ ers

• High Power Current Feedback Circuitry

• Massive Energy Power Supply, Huge EI Transformer, Large ELCO’s.

• 192 kHz/24 bit Crystal

DAC for all 8 Channels

• 32 bit Digital Surround Processing Chipsets

• Video Off Mode

• Large Heavy Duty Speaker Terminals for all Channels

• RS-232C Terminal for System Control (SR5001only)

• Set Up Menu via all Video Output (Composite, SVideo and Component video)

• Auto Input Signal Detection

• Improved Station Name Input Method, 50 Presets

• Auto Adjust Function for Speaker Distance Settings (Delay Time)

• Front AUX Input (Digital Camera, Portable DVD)

• Universal remote control

• Simple Setup Function

• Video convert system

• LIP.SYNC Funciton (Audio delay) (SR5001 only)

ACCESSORIES

Remote Controller RC5001SR

AITP

I I

M-CH ST

EX/ES

STEREO

7.1CH IN NIG

CH/C

SPKR A/B

A/D

+10

HT-EQ

OSD

LTI/CAT

M O

VOLLUME

M-SPKR

T.TON S E

E T UP

ENTER

BASS

PRESET

DIS

C+

CH-S

ANG

-OF BT

ITLE

TUNER

V D

TAPE

CDR

X 1

S SV

AUX

AMP E C

5 50

O LL

E R

AAA-size batteries × 2

AM Loop Antenna

FM Antenna

AC Power Cord

Front AUX Jack Cover

PUSH

User Guide

Warranty Card

USA × 1 Canada × 1

T.DIS

PTY

E XIT

F.DIRECT T UNING

DIO

LEARN

S O

U RC

l/l/

SEND

SLEEP

SET

ISPLA

P.DIRECT

O N

SURR d ts

OUN

LIP

VIRTUAL

A N

T.MO

P.S

CAN

ENGLISH

FRONT PANEL

SR4001

qw yu !3io!0t!2!1re

AV SURROUND RECEIVER SR4001

INPUT SELECTOR

7.1 CH INPUT

STANDBY

POWER ON/STANDBY

SR5001

qw yu !3io!0t!2!1re

AV SURROUND RECEIVER SR5001

INPUT SELECTOR

MULTI

STANDBY

POWER ON/STANDBY

S.SPEAKER B

MULTI

q POWER switch and STANDBY

indicator

When this switch is pressed once, the unit turns ON

y SURROUND MODE button

You can select the surround mode by pressing this button.

and the display illuminates. When pressed again, the unit turns OFF and the STANDBY indicator will be illuminated.

w MULTI (Multi Room) button

(SR5001 only)

VOLUME

Press this button to activate the Multiroom system. “MULTI” indicator will be illuminated in the display.

u PURE DIRECT button and

indicator

When this button is pressed once, “SOURCE DIRECT” appears on the FL display. If pressed again, “PURE DIRECT” appears. After 2 seconds, the FL display indication goes out. In the source/pure direct mode, the tone control circuitry and bass management are bypassed.

DOWN

SIMPLE

PURE

SURROUND

MODE

PHONES

AUTO

SETUP

DIRECT

HT-EQ

ENTER

MEMORY

DISPLAY

EXIT

CLEAR

T-MODE

BAND

MUTE

AUX 1 INPUT

DIGITAL

S-VIDEO

w 7.1CH INPUT button (SR4001 only)

Press this button to select the output of an external

ATT

RLVIDEO

AUDIO

multichannel player.

e INPUT SELECTOR knob

(AUDIO/ VIDEO)

This knob is used to select the input sources. The video SOURCE, such as TV, DVD, VCR1 and

Notes:

• The surround mode is automatically switched to AUTO when the pure direct function is turned on.

• Additionally, speaker configurations are fixed automatically as follows.

Front SPKR = LARGE Center SPKR = LARGE Surround SPKR = LARGE Surround Back SPKR = LARGE Sub woofer = YES

DSS, selects video and audio simultaneously.

!5!6!7!8 @3!9@0@1@2

Audio function sources such as CD, TAPE, CDR/MD, and TUNER may be selected in conjunction with a Video source. This feature (Sound Injection) combines a sound from one source with a picture from another. Choose the video source ﬁ rst, and then choose a

i SIMPLE SETUP button

Press this button to enter the simple setup mode. You can setup the speaker conditions (speaker sizes, number of speakers, speaker delay times) quickly by pressing the cursor buttons.

different audio source to activate this function.

o DISPLAY button

r M.(Multi Room) SPEAKER button

(SR5001 only)

VOLUME

DOWN

READY

Press this button to activate the Multiroom Speaker system. “MULTI” indicator will be illuminated in the display.

(See page 46)

r S.(Surround) SPEAKER B button

SURROUND

SPEAKER

PHONES

MODE

AUTO

SETUP

DIRECT

HT-EQ

ENTER

MEMORY

DISPLAY

EXIT

CLEAR

T-MODE

BAND

MUTE

DIGITAL

S-VIDEO

AUX 1 INPUT

ATT

RLVIDEO

AUDIO

(SR4001 only)

Press this button to activate the Surround Speaker B system . “SPKR B” indicator will be illuminated in the display.

(See page 47)

SIMPLE

PURE

t INFRARED receiving sensor

When this button is pressed, the FL display mode is changed as Surround Mode → Auto-display Off → Display Off → Input Function and the display off indicator(DISP) lights up in condition of DISPLAY OFF.

!0 MEMORY button

Press this button to enter the tuner preset memory numbers or station names. (See page 39)

!1 CLEAR button

Press this button to cancel the station-memory setting mode or preset scan tuning. (See page 39)

window

!5!6!7!8 @3!9@0@1@2

This window receives infrared signals for the remote control.

!2 VOLUME control knob

Adjusts the overall sound level. Turning the control clockwise increases the sound level.

!3 ATT (Attenuate) button

If the selected analog audio input signal is greater than the capable level of internal processing, the PEAK indicator will illuminate. If this happens, you should press the ATT button. “ATT” is displayed when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of “REC OUT” (TAPE, CD-R/MD, VCR1 and VCR2 output). This function is memorized for each input function.

!4 MUTE button

Press this button to mute the output to the speakers. Press it again to return to the previous volume level.

!5 T-MODE button

Press this button to select the auto stereo mode or mono mode when the FM band is selected. The “AUTO” indicator lights in the auto stereo mode. (See page 39)

@1 AUTO (Auto surround) button

Press this button to select the AUTO mode from the surround modes. When this mode is selected, the receiver determines the surround mode corresponding to a digital input signal automatically.

HEADPHONE jack for stereo headphones

This jack may be used to listen to the SR4001/ SR5001’s output through a pair of headphones. Be certain that the headphones have a standard 1 / 4” stereo phono plug. Note that the main room speakers will automatically be turned off when the headphone jack is in use.

Notes:

• When using headphones, the surround mode will change to STEREO and Dolby Headphone by MENU and Cursor button.

• The surround mode returns to the previous setting as soon as the headphone plug is removed from the jack.

ENGLISH

!6 BAND button

Press this button to switch between FM and AM in the TUNER mode.

!7 EXIT button

This button is used to exit from the SETUP MAIN MENU.

!8 Cursor (1, 2, 3, 4) / ENTER button

Use these buttons when operating the SETUP MAIN MENU and TUNER function.

!9 MENU button

This button is used to enter the SETUP MAIN MANU.

@0 HT-EQ button

Used to turn on or off HT(Home Theater)-EQ mode. This mode compensates for the audio portion of a movie sounding “bright”. When this button is pressed, “EQ” indicator lights up.

@3 AUX1 INPUT jacks

These auxiliary video/audio input jacks accept the connections of a camcorder, portable DVD, game etc.

ENGLISH

™

FL DISPLAY

DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG

SURR

AUTO

SLEEP

DIRECT DISC 6.1 MT X 6.1 SPKR B EQ

h k¡0 ¡2 ¡4f

¡8

a DISP (Display Off) indicator

This indicator is illuminated when the SR4001/ SR5001 is in the display off condition.

s SLEEP timer indicator

This indicator is illuminated when the sleep timer function in the main-room is in use.

d Multi-room system indicator

This indicator is illuminated when the multi-room system is active.

f AUTO SURR (Auto Surround

mode) indicator

This indicator is illuminated to show that the AUTO SURROUND mode is in use.

g TUNER’s indicators

AUTO : This indicator illuminates when the

TUNED : This indicator illuminates when

ST(Stereo) : This indicator illuminates when an

tuner’s Auto mode is in use.

a station is being received with sufﬁ cient signal strength to provide acceptable listening quality.

FM station is being tuned into stereo condition.

h DTS-ES mode indicators

(DISC6.1, MTX6.1)

These indicators will illuminate to show the DTS-ES decoding mode (Discrete 6.1 or Matrix 6.1).

j l ¡1

j V (video)-OFF mode indicator

This indicator is illuminated when the Video-OFF function is active.

k NIGHT mode indicator

This indicator is illuminated when the SR4001/ SR5001 is in the Night mode, which reduces the dynamic range of digital program material at low volume levels.

l SPKR (speaker) B indicator

This indicator is illuminated when the M (Multiroom) speaker B system is active.

¡0 PEAK indicator

This indicator is a monitor for an analog audio input signal. If the selected analog audio input signal is greater than the capable level of internal processing, this will illuminate. If this happens, you should press the ATT button on the remote.

¡1 EQ mode indicator

This indicator is illuminated when the HT-EQ function is active.

¡2 ATT (Attenuation) indicator

This indicator is illuminated when the attenuation function is active.

¡3 DIGITAL Input Indicator

This indicator lights when a digital input has been selected.

ATT

¡3

DIGITAL

PCM

¡5d

SURROUND

DIGITAL

LFE

SL S SR

¡4 ANALOG input indicator

This indicator is illuminated when an analog input source has been selected.

¡5 SIGNAL FORMAT indicators

2 DIGITAL, EX, 2 SURROUND, dts, ES, 96/24, PCM

HOW TO ATTACH THE FRONT AUX JACK COVER

T-MO

DIG

PUSH

7.1C H INPU

I O

When the selected input is a digital source, some of these indicators will be illuminated to display the speciﬁ c type of signal in use.

Front AUX Jack Cover

¡6 ENCODED CHANNEL STATUS

indicators

These indicators display the channels that are encoded with a digital input signal. If the selected digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”, “SR” and “LFE” will be illuminated.If the digital input signal is 2 channel PCM-audio, “L” and “R” will be displayed. If Dolby Digital 5.1ch signal with Surround EX ﬂ ag or DTS-ES signal comes in, “L”, “C”, “R”, “SL”, “S” , “SR” and “LFE” will be illuminated.

¡7 Main Information Display

This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of unit’s operation.

¡8 DIRECT (Puredirect) indicator

This indicator is illuminated when the SR4001/ SR5001 is in the SOURCE DIRECT mode.

¡9 HDCD indicator

When HDCD signal is decoded from digital input, this indicator will light up.

™0 HDMI indicator

This indicator is illuminated when HDMI device is connected to the SR4001/SR5001.

REAR PANEL

SBR

SBL

SPEAKER SYSTEMS : MINIMUM 6 OHMS

CENTER

FRONT

SURROUND BACK

S. SPEAKER B

SURROUND

COAX

OUT RC-5

OPT

DIGITAL OUT

( AUX2

)

7.1CH INPUT

SBL

SBR

(

Ω

)

GNDAMAM

ANTENNA

DIGITAL IN

OUTININ

CDR/MD

OUTININ

TAPE

VCR1

DVDTVTV

AUDIO

DSS/VCR2

OUT

AC IN

MODEL NO. SR4001

DSS/VCR2

DVD

VCR IN

VCR OUT

MONITOR OUT

INPUT

S-VIDEO

VIDEO

PRE OUT

INPUT 2

OUTPUT

INPUT 1

HDMI Ver 1.1

COMPONENT

VIDEO

MONITOR

OUT

1.25A 150W

AC OUTLETS 120V 60Hz

UNSWITCHED

SWITCHED

1.25A 150W

FLASHER

q r !

t !

RS-232C

SPEAKER C

OFFONON

FLASHER

TRIGGER

SBR

SBL

COAX

OUT RC-5

OPT

DIGITAL OUT

(

AUX2

)

7.1CH INPUT

SBL

SBR

(

Ω

)

GNDAMAM

ANTENNA

OUTININ

CDR/MD

OUTININ

TAPE

VCR1

DVDTVTV

AUDIO

DSS/VCR2

OUT

DSS/VCR2

DVD

VCR IN

VCR OUT

MONITOR OUT

INPUT

S-VIDEO

VIDEO

PRE OUT

INPUT 2

OUTPUT

INPUT 1

HDMI Ver 1.1

COMPONENT

VIDEO

MODEL NO. SR5001

INPUT

MONITOR

OUT 2

DIGITAL IN

MULTI.

OUT

CENTER

SURROUND

SURROUND BACK

SPEAKER C/MULTI SPEAKER

SURR,SURR BACK:MINIMUM 6 OHMS

FRONT B B

FRONT A A

AC IN

FRONT A OR B,CENTER, FRONT A AND B:MINIMUM 8 OHMS

SPEAKER SYSTEMS

1.25A 150W

AC OUTLETS

120V 60Hz

UNSWITCHED

SWITCHED

1.25A 150W

SR4001

VIDEO

GND

SLSLSBL

SWSWSBR

PRE OUT

S-VIDEO

TVTVDVD

VCR IN

DVD

(

)

7575Ω

ANTENNA

LLSLSLCCSBL

RRSRSRSWSWSBR

(

)

AUX2

7.1CH INPUT

RRSR

INPUT

DSS/VCR2

VCR OUT

ININOUT

VCR1

DSS/VCR2

FRONT

SPEAKER SYSTEMS : MINIMUM 6 OHMS

MONITOR OUT

TAPE

AUDIO

SURROUND BACK

S. SPEAKER B

VIDEO IN/OUT (TV, DVD, VCR1, DSS/ VCR2)

These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video conﬁ gurations. Connect VCRs, DVD players, and

other video components to the video inputs. The 2 video output channels can be used to be connected to video tape recorders for making

INPUT

COMPONENT

VIDEO

MONITOR

OUT

LLR

CDR/MD

SURROUND

OUT

DIGITAL IN

CENTER

DIGITAL OUT

COAX

OPT

OUT

RC-5

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

AC OUTLETS

120V 60Hz

FLASHER

HDMI Ver 1.1

INPUT 2

INPUT 1

AC IN

OUTPUT

MODEL NO. SR4001

recordings. The input signals of video and S-video are converted each other, and each of the converted video signals can be output.

w FM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most

areas. Position the loop antenna until you hear the best reception.

t MONITOR OUT

This is a monitor output and each one includes both composite video and S-video conﬁ gurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections.

y Preamp Outputs

(L, R, SL, SR, SBL, SBR, C)

Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power ampliﬁ ers.

u AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall. SR4001/SR5001 can be powered by 120V AC only.

i AC OUTLETS

Connect the AC power cable of component such as a DVD or CD player to this outlet.

ENGLISH

The marked SWITCHED provides power only when

e RS-232C (SR5001 only)

SR5001

!1 q r !6

!8w

The RS-232C port is to be used in conjunction with an external controller to control the operation of the SR5001 by using an external device.

r COMPONENT VIDEO INPUT/

INPUT

DSS/VCR2

LLR

INPUT

MONITOR OUT

TAPE

AUDIO

SURROUND BACK

SPEAKER C/MULTI SPEAKER

OUT

CDR/MD

SURROUND

SPEAKER SYSTEMS

CENTER

VIDEO

(

)

7575Ω

ANTENNA

LLSLSLCCSBL

RRSRSRSWSWSBR

(

)

AUX2

7.1CH INPUT

RS-232C

SLSLSBL

RRSR

PRE OUT

e!9

S-VIDEO

GND

SPEAKER C

OFF

SWSWSBR

TVTVDVD

VCR IN

VCR OUT

MULTI.

OUT

FRONT A OR B,CENTER, FRONT A AND B:MINIMUM 8 OHMS

DVD

FRONT

ININOUT

VCR1

FRONT

SURR,SURR BACK:MINIMUM 6 OHMS

COMPONENT

INPUT

VIDEO

MONITOR

OUT 2

223

DIGITAL IN

COAX

OPT

DIGITAL OUT

UNSWITCHED

AC OUTLETS 120V 60Hz

OUT RC-5

1.25A 150W

SWITCHED

1.25A 150W

INPUT 1

FLASHER

TRIGGER

AC IN

HDMI Ver 1.1

INPUT 2

OUTPUT

MODEL NO. SR5001

!7i

OUTPUT

If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR4001/ SR5001. The SR4001/SR5001 has two component video input connectors to obtain the color information

(Y, C

, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. When the video convert function is enabled, video and S-video images can be output to the COMPONENT MOINTOR OUT jack.

the SR4001/SR5001 is turned on and is useful for components which you use every time you play your system.

Caution:

• In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR4001/SR5001 is turned on.

• The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of these AC outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.

o Speaker outputs terminals

Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers.

Note:

You can use surround back speaker terminals as M (Multiroom) SPEAKER B terminals, when you use no surround back speaker.

ENGLISH

!0 Subwoofer Output

Connect this jack to the line level input of a powered subwoofer. If an external subwoofer ampliﬁ er is used, connect this jack to the subwoofer ampliﬁ er input. If you are using two subwoofers, either powered or with a 2 channel subwoofer ampliﬁ er, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer ampliﬁ er.

!1 7.1 CHANNEL or AUX2 INPUT

By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with

5.1 channel or 7.1 channel outputs.

!2 Multiroom Outputs (SR5001 only)

These are the audio output jacks for the Multi zone (Multi room). Connect these jacks to optional audio power amplifiers to listen the source selected by the multiroom system in a remote room.

!3 REMOTE CONT. IN/OUT terminals

Connect to a Marantz component equipped with remote control (RC-5) terminals.

!4 AUDIO IN/OUT (CD, TAPE, CD-R,

TV, DVD, VCR1, DSS/VCR2)

These are the analog audio inputs and outputs. There are 7 audio inputs (4 of which are linked to video inputs) and 4 audio outputs (2 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD

players and etc.... The audio inputs and outputs

require RCA-type connectors.

!5 DIGITAL INPUT

(SR4001 : Dig.1 - 4, SR5001 : Dig.1-5) / OUTPUT (coaxial, optical)

These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 2 with optical jacks. The inputs accept digital audio signals from a CD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, or other similar components.

!6 HDMI INPUT/OUTPUT

This unit has 2 HDMI inputs and 1 HDMI output. The input function can be selected from the system

. (See page 26)

OSD menu

!7 DC TRIGGER output terminal

(SR5001 only)

Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system OSD setup menu to determine the conditions by which these jack will be active.

Note:

This output voltage is for (status) control only, It is not sufﬁ cient for drive capability.

!8 FLASHER IN

(Flasher input terminal)

These terminals are to control the unit from each zone. Connect the control signal from a Keypad, etc.

SPEAKER C SELECTOR SWITCH (SR5001 only)

The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 23.

XM antenna terminal (SR5001 only)

Plug the XM Connect-and-play antenna or Passport system into XM terminal.

REMOTE CONTROL

‹

‹ ‹

‹

OPERATION

FUNCTION AND OPERATION

The provided remote control unit is a universal remote controller. The POWER button, numeric buttons and control buttons are used in common across different input source components. The input source controlled with the remote control unit changes when one of the input selector buttons is pressed.

‹5

SEND

z x c v b

m , . ⁄0 ⁄1

⁄2

⁄3 ⁄4

⁄5 ⁄6

LEARN

SET

SOURCE

P.DIRECT

DISPLAY

123

EX/ES

VIRTUAL

456

STEREO

789

7.1CH IN

CAT

SPKR A/B

CAT

MULTI/

M-SPKR

ENTER

T.DISP

REC

PRESET

ANGLE

SUB TITLE

V-OFF

BASS

DVD

AUX1

TAPE

REMOTE CONTROLLER

RC5001SR

CH/

SLEEP

AUTO

M-CH ST

INFO

T.TONE /SET UP

DISC+

CH-SEL

TUNER

NIGHT

A/D

+10

MUTE

PTY

ATT.

CDR

AUX2

⁄7

OFF

SURROUND

LIP SYNC/ INPUT

dts

BAND

T.MODE

P.SCAN

HT-EQ

MEMO

VOLUME

⁄8 ⁄9 ¤0 ¤1 ¤2

¤3

¤4 ¤5 ¤6

¤7 ¤8

¤9

TUNING

EXIT

F.DIRECT

AUDIO

‹0

1 2

TREBLE

VCR

DSS

AMP

z LEARN indicator

Indicates when the remote controller is in the LEARN mode.

x SET button

This button is used to enter learn mode and preset mode.

c / SOURCE ON/OFF button

This button is used to turn a speciﬁ c source (such as a DVD player) on or off independently from the rest of the system.

v SLEEP button

This button is used for setting the sleep timer.

b DISPLAY button

Selects the display mode for the front display of the SR4001/SR5001.

n Numeric buttons

These buttons are used to switch between 0 to +10 of the source components. If the source is set to the ampliﬁ er, these buttons are used to perform operations.

(When AMP mode is selected)

1/AUTO button

Used to select auto surround.

2/Dolby button

Used to select DOLBY mode.

3/dts button

Used to select dts mode.

4/CSII button

Used to select CSII mode.

5/EX/ES button

Used to select EX/ES mode.

6/VIRTUAL button

Used to select VIRTUAL mode.

7/M-CH ST button

Used to select Multi Channel Stereo.

8/STEREO button

Used to select STEREO mode.

9/NIGHT button

Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only in the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back. When this button is pressed, the “NIGHT” indicator is illuminated.

0/7.1CH IN button

Press this button to select the output of an external multi channel decoder.

(+10) A/D button

Used to switch between the analog and digital inputs.

m CL (Clear) button

This button is used to erase the memory or program of a source.

, SPKR A/B button (SR5001 only)

Used to select the speaker system. The speaker system is switched in the following sequence. A → B → A+B → off

. CH/CAT3 (UP) / 4 (DOWN) buttons

These buttons are used to change channels.

⁄0 MULTI/CAT button (SR5001 only)

(When AMP mode is selected)

Used to turn on and off multi room.

⁄1 INFO button

(When AMP mode is selected)

When this button is pressed, the current setting are displayed on the TV monitor.

⁄2 T.TONE/SET UP button

(When AMP mode is selected)

Used to enter the test tone menu.

⁄3 CONTROL buttons

These buttons are used when operating PLAY, STOP, PAUSE and other commands of a source.

(When TUNER mode is selected)

T.DISP button

Used to select the display mode in RDS.

PTY button

Used to display the programme type information of the current station.

F.DIRECT button

Used to select the "Frequency direct input".

PRESET +/- buttons

Used to select a preset station up and down.

TUNING +/- buttons

Used to tune a frequency station up and down.

⁄4 ANGLE/V-OFF buton

(When AMP mode is selected)

Used to turn off the video signal.

⁄5 DISC+/CH. SEL button

(When AMP mode is selected)

Used to call up SETUP MAIN MENU and adjust speaker levels or 7.1 ch input level.

⁄6 BASS +/- buttons

These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.

⁄7 SEND indicator

Indicates when the remote controller is transmitting a signal.

⁄8 / POWER ON and OFF buttons

(When AMP mode is selected)

These buttons are used to turn the SR4001/SR5001 on or off.

⁄9 SURROUND button

This button is used to selects the surround mode.

¤0 P.DIRECT button

When this button is pressed, the tone control circuit is bypassed.

ENGLISH

¤1 BAND/LIP SYNC/INPUT button

(When TUNER mode is selected)

Used to select a radio band.

(When AMP mode is selected)

Used to select LIP SYNC mode.

(When TV mode is selected)

Used to select monitor input.

¤2 T.MODE button

(When TUNER mode is selected)

Used to select auto stereo mode or mono mode when the FM band is selected. The “AUTO” indicator lights in the auto stereo mode.

¤3 P.SCAN button

(When TUNER mode is selected)

Used to start preset scan.

¤4 MEMO/HT-EQ button

This button is used to store setting to memory or program a source.

(When AMP mode is selected)

Used to turn on or off HT(Home Theater)-EQ mode when the surround mode is set as AUTO, DOLBY, DTS or STEREO. This mode compensates for the audio portion of a movie sounding “bright”. When this button is pressed, “EQ” indicator light up.

¤5 MUTE button

This button is used to mute the audio for the ampliﬁ er and television.

Note:

Set the AMP mode to use this button with the SR4001/ SR5001.

¤6 VOLUME +/- buttons

This button is used to adjust the volume for the ampliﬁ er and television.

Note:

Set the AMP mode to use this button with the SR4001/ SR5001.

¤7 M-SPKR button

(When AMP mode is selected)

Used to turn on and off multi speaker.

(SR5001 only)

¤8 MENU button

(When AMP mode is selected)

This button is used to call up the SETUP MAIN MENU of the SR4001/SR5001.

¤9 1, 2, 3, 4 (CURSOR) / ENTER buttons

These buttons are used when controlling the cursor of the SR4001/SR5001, DVD or other AV equipment.

‹0 EXIT button

(When AMP mode is selected)

This button is used to cancel setting in the setup menu.

‹1 SUBTITLE/ATT. button

(When AMP mode is selected)

When the input signal is too high and the voice distorts even by throttling the SR4001/SR5001 VOLUME control, turn on this function. “ATT ” is indicated when this function is activated. The input level reduced. Attenuator is invalid for the output signal of “REC OUT”.

Note:

This function is unavailable while the digital input is selected.

‹2 AUDIO buttons

(When DVD mode is selected)

Used to select one of the audio language.

‹3 TREBLE +/- buttons

These buttons are used to adjust the tone control of high frequency sound for left and right speaker.

‹4 SOURCE button

These buttons are used to switch the source of your A/V Receiver / amplifer. Each time a source button is pressed, the remote control changes to the source which was pressed. This remote control can control 12 types of equipment. To change the A/V Receiver / ampliﬁ er source, press this button twice within two seconds. The signal is sent when it is pressed the second time.

Note:

Select the AMP as the source to use this remote controll with the SR4001/SR5001.

‹5 Infrared Transmitter and Learning

Sensor

This transmitter emits infrared light. Press the buttons while pointing the transmitter towards the infrared receiver window of the SR4001/SR5001 or other AV equipment. Be sure to also point towards other remote controls when using the learning function.

OPERATION OF REMOTE CONTROL UNIT

REMOTE CONTROL

The distance between the transmitter of the remote control and the IR SENSOR of the SR4001/SR5001 should be less than 5 meters. If the remote control is pointed in a direction other than the IR SENSOR or if there is an obstacle between them, use of the remote control may not be possible.

Remote-controllable range

I N P

U T S E L

M U

L T I

S T A

N D B Y

P O

W ER

O N /O

Approx. 5 m

60°

S YS T

E M R

OT R C

O 0 0

N S

Remote control unit (RC5001SR)

TR O L LE

O U ND

R E C EIVE

R S R

50 01

. S P E AK

ER B

S U

R R O M

E O N ES

P U R D

E I R E C

S I M P

S L E

E TUP

H T-EQ

M E NU

D I S P

L A

Y ENTE

M E M

E XI

B A

SR4001/SR5001

V O L U M E

O R

W N

CLEA

N D

M O D E

UP T E

D I

G I T A L

7 . 1

C H I N P

V I D E

X V I

1 D

P U T

A U D I O

LOADING BATTERIES

The life of the batteries used with the remote control is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak.

1. Remove the back cover.

2. Insert the new batteries (AAA type) with correct

and polarity.

CAUTIONS ON BATTERIES

• Use “AAA” type batteries in this remote control unit.

• We recommend that you use alkali batteries.

• If the remote control unit does not operate from close to the main unit, replace the batteries with new ones, even if less then a year has passed.

• The included battery is only for verifying operation. Replace it with a new battery as soon as possible.

• When inserting the batteries, be careful to do so in the proper direction, following the + and - marks in the remote control unit’s battery compartment.

• To prevent damage or battery ﬂ uid leakage:

- Do not use a new battery with an old one.

- Do not use two different types of batteries.

- Do not short-circuit, disassemble, heat or

dispose of batteries in ﬂ ames.

• Remove the batteries when not planning to use the remote control unit for a long period of time.

• If the batteries should leak, carefully wipe off the ﬂ uid from the inside of the battery compartment, then insert new batteries.

• When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

ENGLISH

3. Close the cover until it clicks.

Notes:

• Do not mix alkaline and manganese batteries.

• Do not mix old and new batteries.

ENGLISH

GENERAL INFORMATION OF RC5001SR TO SR4001/SR5001

To control the SR4001/SR5001 by your RC5001SR, you have to select the device AMP or TUNER by pressing the SOURCE button. Please refer below for the details in AMP and TUNER mode.

AMP MODE

SOURCESOURCE

l/l/

SLEEPSLEEP

AUTOAUTO

11 22 33

CSCS

44 55 66

M-CH STM-CH ST

77 88 99

CAT

CH/

INFOINFO

T.TONET.TONE /SET UP/SET UP

REC

DISC+DISC+

CH-SELCH-SEL

TUNER

TAPE

LEARN

SET

DISPLAYDISPLAY

EX/ESEX/ES

STEREOSTEREO

7.1CH IN7.1CH IN

SPKR A/BSPKR A/B

CAT

MULTI/MULTI/

ENTERENTER

T.DISP

PRESET

ANGLEANGLE

V-OFFV-OFF

BASSBASS

DVD

AUX1

REMOTE CONTROLLER

RC5001SR

P.DIRECTP.DIRECT

VIRTUALVIRTUAL

NIGHTNIGHT

+10+10

M-SPKRM-SPKR

SUB TITLESUB TITLE

AUX2

TUNER MODE

SEND

OFF

ONON

SURROUNDSURROUND

LIP SYNC/LIP SYNC/ INPUTINPUT

dtsdts

BAND

T.MODE

P.SCAN

HT-EQHT-EQ

A/DA/D

MEMOMEMO

VOLUME

MUTEMUTE

MENUMENU

EXITEXIT

F.DIRECT

PTY

TUNING

AUDIOAUDIO

ATT.ATT.

TREBLETREBLE

VCR

DSS

CDR

AMP

SOURCE ON / OFF Turns the SR4001/SR5001 on and off

POWER OFF Turns the SR4001/SR5001 off

POWER ON Turns the SR4001/SR5001 on

SLEEP Sets the sleep timer function

DISPLAY Changes the front display mode

P.DIRECT Selects the pure direct mode

SURROUND Selects the surround mode

AUTO (1) Selects auto surround

DOLBY (2) Selects DOLBY mode

dts (3) Selects dts mode

CSII (4) Selects CSII mode

EX/ES (5) Selects EX/ES

VIRTUAL (6) Selects VIRTUAL mode

M-CH ST (7) Selects Multi Channel Stereo

STEREO (8) Selects STEREO mode

NIGHT (9) Turns on or off NIGHT mode

7.1CH IN (0) Selects the 7.1CH IN

A/D (+10) Switches between the analog or digital inputs

LIP SYNC / INPUT Selects the LIP SYNC mode

HT-EQ Turns on or off HT-EQ mode

SPKR A / B Selects the speaker system

MULTI / CAT Turns on or off multi room

LEARN

SOURCESOURCE

l/l/

SLEEPSLEEP

DISPLAYDISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT

CH/

SPKR A/BSPKR A/B

MULTI/MULTI/

INFOINFO

T.TONET.TONE /SET UP/SET UP

T.DISPT.DISP

REC

PRESETPRESET

ANGLE

DISC+

CH-SEL

V-OFF

BASS

TUNER

AUX1

TAPE

REMOTE CONTROLLER

DVD

RC5001SR

SEND

OFFONSET

P.DIRECTP.DIRECT

SURROUNDSURROUND

LIP SYNC/LIP SYNC/

INPUTINPUT

dtsdts

BAND

T.MODET.MODE

VIRTUALVIRTUAL

P.SCANP.SCAN

NIGHTNIGHT

HT-EQHT-EQ

A/DA/D

MEMOMEMO

+10+10

VOLUMEVOLUME

MUTEMUTE

CAT

M-SPKRM-SPKR

MENUMENU

ENTERENTER

EXITEXIT

F.DIRECTF.DIRECT

PTYPTY

TUNINGTUNING

++++

AUDIO

SUB TITLE

ATT.

TREBLE

VCR

DSS

CDR

AMP

AUX2

MUTE Decreases the sound temporarily

M-SPKR Turns on or off multi speaker

VOLUME 3 /

Adjusts the over all sound level

INFO Turns on or off the "On Screen Display"

MENU Displays the current setting on the monitor

ENTER

Enters the "On Screen Display"

Conﬁ rms the setting in "On Screen Display" mode

CURSOR Moves the cursor for setting in "On Screen Display" mode

T.TONE / SET UP Enters the test tone menu

EXIT Exits from SETUP MENU

CH-SEL Calls up SETUP MENU and adjusts speaker levels or 7.1ch input level

V-OFF Turns on or off video output

ATT. Reduces the input level

BASS 3 /

TREBLE 3 /

Adjusts the tone control of low frequency sound

Adjusts the tone control of high frequency sound

SOURCE Selects a particular source component

0-9 Inputs the numeric

BAND Selects a radio band

T.MODE Selects the auto stereo mode or mono mode

P.SCAN Starts preset scan

CL Clears the inputting

MEMO Enters the tuner preset memory numbers

INFO Shows preset information

T.DISP Selects the display mode in XM

F.DIRECT Selects the “Frequency direct input”

PRESET 3 / 4Selects a preset station up and down

TUNING 3 / 4Tunes a frequency station up and down

MULTI/CAT Turns XM Category Search mode ON/OFF

CH/CAT Switches categories in Category Search mode

CONTROLLING MARANTZ COMPONENTS

1. Press the desired SOURCE button.

2. Press the desired operation buttons to play the selected component.

• For details, refer to the component’s user guide.

• It may not be possible to operate some models.

ENGLISH

CONTROLLING A MARANTZ DVD PLAYER (DVD MODE) CONTROLLING A MARANTZ VCR (VCR MODE)

LEARN

SET

SOURCESOURCE

l/l/

SLEEP

DISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT

CH/

SPKR A/B

MULTI/

INFOINFO

T.TONET.TONE /SET UP/SET UP

T.DISPT.DISP

REC

PRESET

ANGLEANGLE

DISC+DISC+

CH-SELCH-SEL

V-OFFV-OFF

BASS

DVD

TUNER

AUX1

TAPE

REMOTE CONTROLLER

CAT

ENTERENTER

RC5001SR

P.DIRECT

VIRTUALVIRTUAL

NIGHTNIGHT

+10+10

MUTE

M-SPKR

PTYPTY

SUB TITLESUB TITLE

ATT.ATT.

CDR

AUX2

SEND

OFFOFF

SURROUND

LIP SYNC/

INPUT

dtsdts

BAND

T.MODE

P.SCAN

HT-EQHT-EQ

A/DA/D

MEMOMEMO

VOLUME

F.DIRECTF.DIRECT

TUNING

AUDIOAUDIO

TREBLE

VCR

SOURCE ON / OFF Turns the DVD player on and off

POWER OFF Turns the DVD player off

POWER ON Turns the DVD player on

ONON

0-9,+10 Inputs the numeric

CL Clears the inputting

MEMO Calls up programming menu

INFO Displays the disc information

MENU Calls up the menu of DVD disc

ENTER Enters the setting

CURSOR Mo ves the cursor for setting in

"On Screen Display" mode

T.TONE / SET UP Enters the test tone menu

EXIT Exits from SETUP MENU

MENUMENU

T.Tone/Set up Calls up the setup menu of the

DVD player

Pause Pause

EXITEXIT

Play Play

Stop Stop

Previous/Next S k ip s f o r w ar d o r p r e v io u s

chapter/track

Rewind/ Forward Searchs forward or backward

DISC+ DVD changer next disc

ANGLE Selects the camera angle

DSS

SUBTITLE Selects the subtitle language

AUDIO Selects the audio language

AMP

CONTROLLING A MARANTZ CD (CD MODE)

LEARN

SET

SOURCESOURCE

l/l/

SLEEP

DISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT

CH/

SPKR A/B

MULTI/

INFOINFO

T.TONET.TONE /SET UP/SET UP

T.DISPT.DISP

REC

PRESET

ANGLEANGLE

DISC+DISC+

CH-SELCH-SEL

V-OFFV-OFF

BASS

DVD

TUNER

AUX1

TAPE

REMOTE CONTROLLER

CAT

ENTERENTER

RC5001SR

OFFOFF

P.DIRECT

VIRTUALVIRTUAL

NIGHTNIGHT

A/DA/D

+10+10

MUTE

M-SPKR

PTYPTY

SUB TITLESUB TITLE

ATT.ATT.

VCR

CDR

AUX2

SEND

SURROUND

LIP SYNC/ INPUT

dtsdts

BAND

T.MODE

P.SCAN

HT-EQHT-EQ

MEMOMEMO

VOLUME

F.DIRECTF.DIRECT

TUNING

AUDIOAUDIO

TREBLE

SOURCE ON / OFF Turns the CD player on and off

POWER OFF Turns the CD player off

POWER ON Turns the CD player on

ONON

0-9 Inputs the numeric

CL Clears the inputting

MEMO Programs

INFO Scrolls the disc information

MENU Switches the display information

Pause Pause

Play Play

Stop Stop

Previous/ Next Skips forward or previous track

Rewind/ Forward Searchs forward or backward

MENUMENU

DISC+ CD changer next disc

EXITEXIT

DSS

AMP

LEARN

SET

SOURCESOURCE

l/l/

SLEEP

DISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT CAT

CH/CH/

SPKR A/B

MULTI/

INFOINFO

T.TONET.TONE

/SET UP/SET UP

T.DISPT.DISP

RECREC

PRESET

ANGLE

DISC+

CH-SEL

V-OFF

BASS

DVD

TUNER

AUX1

TAPE

REMOTE CONTROLLER

RC5001SR

SEND

OFF

P.DIRECT

SURROUND

LIP SYNC/ INPUT

dtsdts

BAND

T.MODE

VIRTUALVIRTUAL

P.SCAN

NIGHTNIGHT

A/D

HT-EQ

MEMO

+10

VOLUME

MUTE

CAT

M-SPKR

MENUMENU

ENTERENTER

F.DIRECTF.DIRECT

PTYPTY

TUNING

AUDIOAUDIO

SUB TITLE

ATT.

TREBLE

VCR

DSS

CDR

AMP

AUX2

0-9,+10 Inputs the numeric

LIP SYNC/INPUT Selects TV/VCR

CL Clears the inputting

MEMO Calls up programming menu

CH 3 /

Selects VCR channel up or down

MENU Calls up the menu

ENTER Enters the setting

CURSOR Move s the cursor for setting in

"On Screen Display" mode

EXIT Exits the programming menu

REC Record

Pause Pause

Play Play

Stop Stop

Previous / Next Skips forward or previous track

EXITEXIT

Rewind / Forward Searchs forward or backward

AUDIO Selects the audio language

SOURCE ON / OFF Turns the VCR on and off

ENGLISH

CONTROLLING A MARANTZ CD RECORDER (CDR MODE)

LEARN

SET

SOURCESOURCE

l/l/

SLEEP

DISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT

CH/

SPKR A/B

MULTI/

INFOINFO

T.TONET.TONE /SET UP/SET UP

T.DISPT.DISP

RECREC

PRESET

ANGLE

DISC+

CH-SEL

V-OFF

BASS

DVD

TUNER

AUX1

TAPE

REMOTE CONTROLLER

CAT

ENTERENTER

RC5001SR

P.DIRECT

VIRTUALVIRTUAL

NIGHTNIGHT

+10

M-SPKR

SUB TITLE

AUX2

SEND

OFFOFF

SURROUND

LIP SYNC/

INPUT

dtsdts

BAND

T.MODE

P.SCAN

A/D

HT-EQ

MEMO

VOLUME

MUTE

MENUMENU

F.DIRECTF.DIRECT

PTYPTY

TUNING

AUDIO

ATT.

TREBLE

VCR

DSS

CDR

AMP

SOURCE ON / OFF Turns the CD recorder on and off

POWER OFF Turns the CD recorder off

POWER ON Turns the CD recorder on

ONON

0-9 Inputs the numeric

CL Clears the inputting

MEMO Programs

INFO Scrolls the disc information

MENU Switches the display information

REC Record

Pause Pause

Play Play

Stop Stop

Previous / Next Skips forward or previous track

Rewind / Forward Searchs forward or backward

EXITEXIT

CONTROLLING A MARANTZ MD DECK (MD MODE)

LEARN

SET

SOURCESOURCE

l/l/

SLEEP

DISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT

CH/

SPKR A/B

MULTI/

INFOINFO

T.TONET.TONE

/SET UP/SET UP

T.DISPT.DISP

RECREC

PRESET

ANGLE

DISC+

CH-SEL

V-OFF

BASS

DVD

TUNER

AUX1

TAPE

REMOTE CONTROLLER

CAT

ENTERENTER

RC5001SR

P.DIRECT

VIRTUALVIRTUAL

NIGHTNIGHT

A/D

+10

MUTE

M-SPKR

PTYPTY

SUB TITLE

ATT.

VCR

CDR

AUX2

SEND

OFFOFF

ONON

SURROUND

LIP SYNC/

INPUT

dtsdts

T.MODE

P.SCAN

HT-EQ

MEMO

VOLUME

MENUMENU

F.DIRECTF.DIRECT

TUNING

AUDIO

TREBLE

DSS

AMP

SOURCE ON / OFF Turns the MD deck on and off

POWER OFF Turns the MD deck off

POWER ON Turns the MD deck on

0-9 Inputs the numeric

CL Clears the inputting

MEMO Programs

MENU Switches the display information

REC Record

Pause Pause

Play Play

Stop Stop

Previous / Next Skips forward or previous track

Rewind / Forward Searchs forward or backward

EXITEXIT

CONTROLLING A MARANTZ TAPE DECK (TAPE MODE)

LEARN

SET

SOURCESOURCE

l/l/

SLEEP

DISPLAY

AUTOAUTO

11 22 33

EX/ESEX/ES

CSCS

44 55 66

STEREOSTEREO

M-CH STM-CH ST

77 88 99

7.1CH IN7.1CH IN

CLCL

CAT

CH/

SPKR A/B

MULTI/

INFOINFO

T.TONET.TONE

/SET UP/SET UP

T.DISPT.DISP

RECREC

PRESET

ANGLE

DISC+

CH-SEL

V-OFF

BASS

DVD

TUNER

AUX1

TAPE

REMOTE CONTROLLER

CAT

ENTERENTER

RC5001SR

P.DIRECT

VIRTUALVIRTUAL

NIGHTNIGHT

+10

MUTE

M-SPKR

PTYPTY

SUB TITLE

ATT.

CDR

AUX2

SEND

OFFOFF

ONON

SURROUND

LIP SYNC/

INPUT

dtsdts

T.MODE

P.SCAN

A/D

HT-EQ

MEMO

VOLUME

F.DIRECTF.DIRECT

TUNING

AUDIO

TREBLE

VCR

DSS

AMP

SOURCE ON / OFF Turns the TAPE deck on and off

POWER OFF Turns the TAPE deck off

POWER ON Turns the TAPE deck on

0-9 Inputs the numeric

CL Clears the inputting

MEMO Programs

REC Record

Pause Pause

Play Play

Stop Stop

Previous / Next Skips forward or previous track

Rewind / Forward Searchs forward or backward

MENUMENU

EXITEXIT

+ 39 hidden pages