Mantis Swift Split User Manual

© 2006 Mantis, Div. of Schiller-Pfeiffer Inc. All Rights Reserved.

Owners Manual and Safety Instructions

Log Splitter Manual

1

Table of Contents

A. Introduction . . . . . . . . . . . . . . . . . . . . . . . .1

B. Log Splitter Specification . . . . . . . . . . . . .1

C. Unpacking and Assembly Instructions . .2

D. Service Information . . . . . . . . . . . . . . . . .5

E. Special Safety Information . . . . . . . . . . . .5

1. Safety Decals . . . . . . . . . . . . . . . . . . . . . . . .5

2. Safety Warnings . . . . . . . . . . . . . . . . . . . . . .7

3. Important extension cord information . . . . .8

4. Always disconnect power cord from

power source . . . . . . . . . . . . . . . . . . . . . . . . .8

5. Hydraulic Safety . . . . . . . . . . . . . . . . . . . . . .8

F. Before You Start Splitting . . . . . . . . . . . .9

G. Operation . . . . . . . . . . . . . . . . . . . . . . . . .11

H.

Removal of logs jammed on the wedge

. . .12

I. How to change the hydraulic oil . . . . . .13

J. Sharpening the wedge . . . . . . . . . . . . . . .14

K. Transport . . . . . . . . . . . . . . . . . . . . . . . . .15

L. Maintenance . . . . . . . . . . . . . . . . . . . . . .15

M. Troubleshooting . . . . . . . . . . . . . . . . . . . .17

N. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .17

O. Exploded View and Parts List . . . . . . . .18

P. Declaration of Conformity . . . . . . . . . . .20

Q. Mantis Warranty Policy . . . . . . . . . . . . .21

A. Introduction

The SwiftSplit log splitter is designed for residential (non­commercial) use and makes your job less physically demanding,
more efficient and safer. With a log splitter, the log is split when
pressed against a fixed splitting wedge by a pressure plate.

Major Components,

Controls, and F

eatures Overview

:

An electric motor assembly provides the power for the system.
The motor is connected to a hydraulic oil pump that creates a flow
of high-pressure oil which runs to a solenoid valve. A switch set and
the solenoid valve let the operator actuate the hydraulic cylinder to
split a log. An internal reservoir holds the hydraulic oil that feeds
the pump. The hydraulic assembly is attached to the wheel frame
assembly, making it easy to move the log splitter around with no
lifting. The frame is equipped with folding handles for storage,
pivoting support for stability and cord storage hooks for
convenience. This log splitter is designed with two hand
operating controls (two normally open switches) for safety. The
electrical motor is protected by a 15 amp circuit breaker. The
pressure relief valve protects the hydraulic assembly. When the log
is jammed, relief valve will prevent pressure from going over its
maximum allowable level.

Maximum Output Force 10,000 lbs (5 tons)

Total Stroke (in)- Ram Travel 15”

Total Weight 135 lbs (61 Kg)

L x W x H 40” L x 20” W x 38” H

Voltage 120V

Motor 1.8 kW

Motor RPM Max 3380 RPM

Maximum Log Length 20” (520mm)

Recomd. Maximum Log Diameter 12” Dia.
Wheel Size 10” Dia.

B. Log Splitter Specification for Model #5005

Wedge

Vertical Beam

Log Guides

Pressure

Plate

Two Switches

Folding

Handle

Wheel
Frame

Assembly

Cord Storage Hooks

Connecting Link

Stabilizing Bar /

Pivoting Support

2

C. Unpacking and Assembly Instructions

1. Cut bands; remove cover and two inserts supporting the top and the bottom of the unit. Remove wheels, pivoting support
and hardware box from the box.

2. Put log splitter in the vertical position by holding the top of the beam and carefully lifting the top of the log splitter until it
can stand.

PIVOTING SUPPORT

#520104 (QTY=1)

WHEELS #520102 (QTY=2)

HARDWARE BAG

LOG SPLITTER WITH ATTACHED HANDLE

10

3

3. Check contents of the hardware bag.

25

29

31

28

2

3

9

ITEM NO.

2
3
7
8
9
11
14

28
29
31
111
25

7

QTY

2
2
2
2
4
2
2
2
2
1
1
1

PART NO.

520500
520101
520105
520501
520502
520503
520505
520116
520510
520117
520516
520113

8

9

11

14

DESCRIPTION

M10 CARRIAGE BOLT,SQUARE NECK, 60mm LONG
KNOB
CONNECTING LINK
BOLT HEX M6 x 40mm
NUT LOCK M6, NYLON INSERT
WASHER FLAT 06
BOLT HEX M6 x 30mm
WHEEL SHAFT
M14 WHEEL NUT
CABLE TIE 152MM (6") LONG
ALLEN WRENCH 8MM (DRAIN PLUG)
DIP STICK SEAL (SPARE)

111

HARDWARE BAG #520517 (QTY=1)

4

4. Folding Handle: Install the folding handle onto the frame using knobs (P/N 520101) and carriage bolts (P/N 520500). To do
this, align square opening of the folding handle with the frame’s round hole and insert carriage bolt through. Secure it with
the handle knob. Repeat the same steps for the opposite side of the handle and tighten the knobs.

5. Use cable ties (P/N 520117) to secure the power cord in place.

6. Installing Wheels: Insert the Wheel Shaft (P/N 520116) in the hub of the Wheel and secure it with the Nut (P/N 520510)
provided. Slide the opposite side of the Wheel Shaft through the opening in the frame and bracket, then screw, it into the
welded nut. Start by hand and then use a wrench and secure the wheel. Repeat these steps to install the second wheel.

5

7. Pivoting Support Installation: Align mounting hole of the Pivoting Support (P/N 520104) with the frame hole, insert Bolt
(P/N 520501) and secure with Lock Nut (P/N 520502). Repeat these steps to attach the other side of the Pivoting Support.

8. Attach Connecting Link (P/N 520105) to the Pivoting Support (P/N 520104).

D. Service Information

Visit our web site at www.swiftsplit.com or contact our customer service department by calling 1-800-366-6268.

E. Special Safety Information

1. Safety Decals

An important part of the safety system incorporated in this log splitter are the Warning Labels (P/N510601) and Information
Decals found on various parts of the unit. These decals must be replaced in time due to abrasion, etc. It is your responsibility
to replace the decals when they become hard
to read.

Lock Nut

Bolt

Pivoting Support

Secure Pivoting support by

attaching connecting link

to the frame (wheel

is not shown for clarity)

P/N 510601

6

WARNING DANGER

READ AND UNDERSTAND THE RULES FOR SAFE

OPERATION AND ALL INSTRUCTIONS IN THIS

MANUAL BEFORE OPERATING THIS PRODUCT.

BE FAMILIAR WITH THE CONTROLS AND THE

PROPER USE OF EQUIPMENT. IMPROPER USE OR

CARE OF THIS LOG SPLITTER, OR FAILURE TO

WEAR PROPER PROTECTION, CAN RESULT IN

SERIOUS INJURY. WEAR EYE PROTECTION,

GLOVES, AND PROPER CLOTHING.

WARNING!

WARNING!

WEAR EYE PROTECTION

READ AND

UNDERSTAND

OPERATOR’S MANUAL

BEFORE USING!

KEEP BYSTANDERS

AND PETS AT A SAFE

DISTANCE

WARNING!

WEAR SLIP-RESISTANT

FOOTWEAR. MAINTAIN

FOOTING AND BALANCE

AT ALL TIMES. DO NOT

STAND ON SLIPPERY,

UNEVEN OR UNSTABLE

SURFACES. DO NOT

WORK IN ODD

POSITIONS.

WARNING!

WEAR SHOES THAT
PROVIDE PROTECTION
AGAINST THE RISK OF

LOGS ACCIDENTALLY

FALLING ON FEET.

!DANGER!

KEEP BOTH HANDS ON

THE SWITCHES AND

AWAY FROM MOVING

PARTS. NEVER REACH

INTO THE CRUSHING

DANGER AREA AS LONG

AS PARTS MAY MOVE.

WARNING!

NEVER REMOVE LOG

JAMMED ON THE

SPLITTING WEDGE

WITH YOUR HANDS!

WARNING!

ALWAYS WEAR WORK

GLOVES TO PROTECT

YOUR HANDS FROM

WOOD CHIPS AND

SPLINTERS

WARNING!

DO NOT EXPOSE TO RAIN

OR WET CONDITIONS

WARNING!

REMOVE PLUG FROM

MAIN ELECTRIC POWER

SOURCE IMMEDIATELY
IF CABLE IS DAMAGED

OR CUT, BEFORE

SERVICING OR WHEN

NOT IN USE

WARNING!

CORRECT LINE

VOLTAGE FOR YOUR

LOG SPLITTER

WARNING!

ALWAYS PAY

ATTENTION TO THE

MOVEMENT OF THE

PRESSURE PLATE

WARNING

DO NOT OPERATE THE SWIFTSPLIT IF THE UNIT IS DAMAGED IN ANYWAY.

3