Mantis 8550 Operator's Manual

Page 1
Cordless Hedge Trimmer
Warning! Read through the operating instructions carefully and observe the instructions contained herein. Familiarize yourself with the machine, its correct use and the safety devices by means of these operating instructions.
8550
OPERATOR / PARTS MANUAL
Page 2
Cordless Hedge Trimmer Operatorʼs Manual
WARNING
CALIFORNIA Proposition 65 Warning
Battery post, terminals, wiring insulation, and
related accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer, birth defects and other
reproductive harm.
WASH HANDS AFTER HANDLING.
Page 3
Contact us at www.mantis.com
This Operator / Parts Manual is part of the machine. Suppliers of both new and second-hand machines must make sure that this manual is provided with the machine.
TABLE OF CONTENTS
PAGE
InTrOducTIOn TO The OPera TIng InSTrucTIOnS...........................................................................4
TechnIcal SPecIfIca TIOnS...................................................................................................................4
SafeTY SIgnS and InTernaTIOnal SYMBOlS....................................................................................4
SafeTY InSTrucTIOnS............................................................................................................................5
InTended uSe...........................................................................................................................................5
general SafeTY InfOrMaTIOn fOr POwer TOOlS........................................................................5
MaIn ParTS................................................................................................................................................8
InSTrucTIOnS fOr uSe Of The equIPMenT......................................................................................8
chargIng The BaTTerIeS......................................................................................................................9
SwITchIng The hedge TrIMMer On/Off ...........................................................................................9
adjuSTIng The SwIVel-clIcK™ handle..........................................................................................10
hOldIng The hedge TrIMMer when In uSe...................................................................................10
MaInTenance..........................................................................................................................................11
OPTIMuM SafeTY.....................................................................................................................................11
STOrIng The hedge TrIMMer afTer uSe.......................................................................................12
enVIrOnMenTal PrOTecTIOn.............................................................................................................12
Thank you for purchasing this Mantis product. Y ou have purchased a world class product, one of the best designed and built anywhere. This machine comes with an Operator / Parts Manual. The useful life and good service your receive from this machine depends to a
large extent on how well you read and understand this manual. Treat your machine properly, lubricate and adjust it as instructed, and it will give you many years of reliable service.
Your safe use of this Mantis product is one of our prime design objectives. Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation. for best protection, study the manuals thoroughly. learn the proper operation of all controls. Observe all safety precautions. follow all instructions and warnings completely. do not remove or defeat any safety features. Make sure those who operate this machine are as well informed and careful in its use as you are.
Mantis designs and builds its equipment to serve many years in a safe and productive manner. for longest life, use this machine only as directed in the manuals, keep in good repair and follow safety warnings and instructions. You’ll always be glad you did.
Schiller Grounds Care, Inc.
1028 Street Road
Southampton, PA 18966 U.S.A.
PHONE (800) 366-6268 • FAX 215-357-8045
IMPORTANT MESSAGE
Page 4
Cordless Hedge Trimmer Operatorʼs Manual
IntroductIon to the operatIng InstructIons
These Operating Instructions are intended to facilitate your becoming acquainted with the product and using it in ac­cordance with the regulations. The Operating Instructions contain important information on how to use the product safely, correctly and economically. Observing this information will help increase the reliability and working life of the product. The Operating Instructions must always be at hand when the product is being used.
They must be read and observed by every person dealing with the product, whether operating, servicing or transporting it. In addition to the Operating Instructions and the applicable rules of the prevention of accidents valid in the country of
use and on site, the generally recognized rules on working safely and correctly must be observed as well as the ac­cident prevention rules of the relevant professional associations.
technIcal specIfIcatIons
cordless hedge trimmer Mantis 8550
Operational voltage 24 V DC Blade length 21.65" Cutting Thickness 0.79" Cutting length 20" Cutting movements Low = 2,200/min; High = 3,000/min Battery type Li-Ion 24 V / 1.9 Ah / 45.6 Wh Run time with a fully recharged battery Low = approx 80 minutes; High = approx 40 minutes Weight 6.7 Ibs
Battery charger
Voltage 100-240 V~ / 0.4 A / 50-60 Hz Charging voltage 25.9 V DC Charging current 500 mA Charging time Approx 3 - 5 hours
Technical changes are reserved.
safetY sIgns and InternatIonal sYMBols
These Operating Instructions describe safety symbols and international symbols and pictographs that may be applied to the device. Read the Operating Instructions to familiarize with all information concerning safety , assembly, operation, maintenance and repair.
1 Use protective means for eyes and ears! 2 Caution! Warning symbols with information on damage and injury prevention. 3 Attention! If you do not adhere to the instructions and safety measures described in the Operating Instructions
severe injuries may occur. Read the Operating Instructions before you start and operate this device. 4 This electric machine must not be exposed to rain or wet conditions. 5 Caution! Injury, sharp cutting knife! 6 Attention: Environmental Protection! This device may not be disposed of with general/household waste.
Dispose of only at a designated collection point. 7 Defective accumulators should be r ecycled! 8 Battery contains lithium! Do not dispose of as household refuse 9 The recharger is for indoor use only.
1 2 3 4 5 6 7 8 9
Page 5
Contact us at www.mantis.com
residual dangers
Residual risks always remain even if the hedge trimmer is used properly. The hedge trimmer‘s design can entail the following hazards:
• Contact can be made with the unprotected blade (resul­ting in cutting injuries)
• Reaching into or grabbing the hedge trimmer while it is in operation (resulting in cutting injuries)
• Unanticipated, sudden movement of the plant material being cut (resulting in cutting injuries)
• Ejection or catapulting of damaged cutting teeth
• Ejection or catapulting of the plant material being cut
Hearing damage if the specied hearing protection is not worn
• Inhalation of cut materials
general power tool safetY w arnIngs
warnIng read all safety warnings and all in­structions! Failure to follow the safety warnings and
instructions may result in electric shock, re and/or
serious injury.
save all warnings and instructions for future reference.
The term ‘power tool’ in the warnings refers to your bat­tery-operated (cordless) power tool.
1) work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) do not operate power tools in explosive atmos-
pheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
2) electrical safety
a) power tool plugs must match the outlet. never
modify the plug in any way. do not use any adapter plugs with grounded power tools. Un-
modied plugs and matching outlets will reduce risk
of electric shock.
b) avoid body contact with grounded surfaces,
such as pipes, radiators, ranges and refrigera­tors. There is an increased risk of electric shock if your body is grounded.
c) do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
d) do not abuse the cord. never use the cord for
carrying, pulling or unplugging the charger. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) when operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of electric shock.
safetY InstructIons
warning!
This appliance is not intended for use by persons (includ­ing children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concern­ing use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Usage of hedge trimmer always involves a risk of ac­cidents, therefore please observe the relevant accident prevention instructions. The machine has been constructed according to the latest technology and in accordance with the recognised techni­cal safety regulations. Nevertheless, use of the machine can involve risks to the user or third persons, and can cause damage to the machine or other objects. Attention: Using electric power tools, you must observe following fundamental safety instructions to protect your­self against electric shock, against danger of injuries and
danger of re. Read all these instructions before using
the hedge trimmer and observe them. Keep these safety instructions at a safe place. Use the machine in a safety conscious manner for suitable applications in a technically perfect condition only and with due regard to the operating instructions! Immediately
rectify or have rectied any faults which could adversely
affect safety! This machine may cause serious injuries. Please read the instruction manual carefully as to the correct handling, the preparations, the maintenance and the proper use of the hedgetrimmer. Familiarize yourself with the machine
before the rst use and also have yourself introduced to
practical use of the machine.
Intended use
This hedge trimmer is only intended to be used to trim shrubs, bushes, ornamental plants and hedges. It is desi­gned to cut branches with a diameter of no more than 0.79" (20 mm). The hedge trimmer is not intended for commercial use. The user of the hedge trimmer must make sure that the protective equipment specied in the operating instruc­tions and by the warning label on the trimmer is attached whenever the trimmer is in use. The hedge trimmer must be checked for electrical or mechanical damage before it is used.
Stop working and contact a specialist workshop if you nd
any damage.
Improper use
Any use not identied in the chapter “Intended use” is an
improper use. The user of the hedge trimmer is solely liable for any pro­perty damage or personal injury arising from improper use of the hedge trimmer. The manufacturer‘s obligation to honor the warranty is vo­ided if the hedge trimmer is used with non-original parts.
Page 6
Cordless Hedge Trimmer Operatorʼs Manual
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (rcd) protected supply. Use of a RCD reduces the risk of
electric shock.
3) personal safety a) stay alert, watch what you are doing and use
common sense when operating a power tool. do not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) use personal protective equipment. always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) prevent unintentional starting. ensure the switch
is in the off-position before connecting to power source and/or battery pack, picking up or carry­ing the tool. Carrying power tools with your nger
on the switch or energising power tools that have the switch on invites accidents.
d) remove any adjusting key or wrench before turn-
ing the power tool on. A wrench or a key left at-
tached to a rotating part of the power tool may result in personal injury.
e) do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
f) dress properly. do not wear loose clothing or
jewelry . Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection, ensure these are con­nected and properly facilities used. Use of dust
collection can reduce dust-related hazards.
4) power tool use and care a) do not force the power tool. use the correct pow-
er tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b) do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c) disconnect the plug from the power source and/
or remove the battery pack from the power tool before making any adjustments, changing acces­sories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. check for misalignment or
binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a haz­ardous situation.
5) Battery tool use and care a) Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
b) Use power tools only with specically desig-
nated battery packs. Use of any other battery packs
may create a risk of injury and re.
c) when battery pack is not in use, keep it away
from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together
may cause burns or a re.
d) under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact ac­cidentally occurs, ush with water. If liquid con­tacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns!
6) service a) Have your power tool serviced by a qualied
repair person using only identical replacement parts. This will ensure that the safety of the power
tool is maintained.
emissions
- The specied vibration emission value was measured by a standardized test methods and can compare with other power tools are used.
- The specied vibration emission value can also be neces- sary for the assessment of work breaks are used.
- The specied vibration emission value can vary during the actual use of the electric tool by specifying the value, depending on the way how to use the power tool.
- Note: You create the privilege against vascular pulsa­tions of the hands in time breaks.
hedge trimmer safety warning:
• use both hands when operating the hedge trimmer. using one hand could cause loss of control and re­sult in serious personal injury.
• Keep all parts of the body away from the cutter blade. do not remove cut material or hold mate­rial to be cut when blades are moving. Make sure
Page 7
Contact us at www.mantis.com
the switch is off when clearing jammed material. Blades coast after turn off. A moment of inattention
while operating the hedge trimmer may result in serious personal injury.
• carry the hedge trimmer by the handle with the cut-
ter blade stopped. Proper handling of the hedge trim- mer will reduce personal injury from the cutter blades. danger - Keep hands away from blade. Contact
with blade will result in serious personal injury.
• hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring. Cutter blades contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give the operator an electric shock.
• please consider environmental inuences. Ensure that there is good lighting.
• the use of hedge trimmers involves certain risks. attention: danger! rotating machinery.
• Before using the equipment clear the working area of any foreign objects and be aware of foreign ob­jects during operation of the machine!
• do not use the trimmer in wet weather and do not use it to cut wet hedges. do not wash down the device with water. do not use any high-pressure cleaning devices or steam jet devices for cleaning.
• ensure that the motor of your hedge shears can not be switched on by mistake when you put it down af­ter work or when you are going to clean the device. never forget to unplug the mains supply!
• Be aware of your responsibility as the user towards third parties in the working area.
• the hedge trimmer must be properly checked and serviced. If the blades get damaged they should only be exchanged in pairs. In the event of damage from impact, specialist’s inspection is essential.
• the lead of the charger and its components must be checked before each use for visible defects (un­plugged). If a defect is found, the charger should not be used.
• ensure that the equipment is stored safely after use in such a way that the blade cannot be touched.
• for initial use of the hedge trimmer we would rec­ommend that in addition to reading the operating instructions, you also seek a practical demonstra­tion from an expert.
• warnIng - only use with handle and guard prop­erly assembled to hedge trimmer. the use of the hedge trimmer without the proper guard or handle provided may result in serious personal injury.
• never try to use an incomplete tool or a tool that has been modied in a way that has not been ap­proved.
• Make yourself familiar with your surroundings (hid­den objects, such as wire fencing) and pay attention to possible hazards you might not hear because of the noise of the machine.
• attentIon! only use the accessories or attach­ments shown in the operating Instructions. the use of other add-on tools and accessories may set up the risk of injury for you.
• Battery tools and battery packs provided with mains connection or non-isolated sources.
• Your power tool is not insulated against electric shock. to reduce the risk of electrocution, never operate this power tool in the vicinity of any wires or cables (power, etc.) which may be carrying electric current. electricity can jump from one point to an­other by means of arcing. higher voltage increases the distance electricity can arc. electricity can also move through branches, especially if they are wet.
Page 8
Cordless Hedge Trimmer Operatorʼs Manual
InstructIons for use of the equIpMent
Do not use the trimmer in rain or for cutting wet hedges!
Gloves: Protective gloves must be worn when using the hedge trimmer.
warnIng: Read and understand this owner’s man­ual before operating Hedge Trimmer. Make certain you read and understand all Safety Warnings of this manual. Improper use of this trimmer can result in
severe injury or death from re, electric shock, or
body contact with moving parts.
Instructions for using the battery
1. The rechargeable battery is not charged when deliv­ered. The battery must be fully recharged before the
rst use of the hedge trimmer (refer to – Charging the
Battery).
2. You must never open the battery.
3. Never throw the used batteries in re - rIsK of
eXplosIon!
4. Connect the battery charger to an outlet with a voltage that is stated on the charger.
5. Use only the original battery.
6. Never charge the battery with a battery charger from another manufacturer. This can result in the battery being damaged or it can result in an injury due to over­heating.
7. During a long-term operation, the battery may heat up. Let it cool down before charging it.
8. Do not store the battery charger and the batteries within children‘s reach.
9. Do not use the battery charger in an environment with
vapors or inammable uids.
10. Charge the batteries only at a temperature within the range of 50°F to 104°F (10°C to 40°C).
11. Store the battery at temperatures up to 104°F (40°C) only. Higher storage temperatures may result in dam­age to the battery.
12. Never short-circuit the contacts of the batteries and never interconnect them with metal objects.
13. When transporting the battery, take care that the con­tacts are not interconnected, do not use metal trans­portation containers.
14. Short-circuit of the battery can lead to explosion. In any case, the short-circuit connection will damage the battery.
15. Check the cable regularly on whether it is damaged. If the cable is damaged, have it replaced.
16. The battery is equipped with a deep-discharge protec­tion feature: the tool is automatically switched off if the battery is discharged. Recharge the battery immedi­ately if this should be the case.
17. Before storing the batteries for the wintertime, charge them fully once more.
disposal of batteries
Please observe the following directions for the disposal of your battery. Batteries are not to be put into the trash. As a consumer you should recycle used batteries. At the end of the dura-
1+2 Operating switches (two-hand operation) 3 Hand guard 4 Battery 5 Blade safety rail 6 Impact protector 7 Locking of the turning handle
MaIn parts
1
Page 9
Contact us at www.mantis.com
• Pull the plug of the charging unit if it is not in use.
• If the battery is not charging, check whether the electri-
cal socket provides current. If the charging of the batter­ies nevertheless is not possible, give the battery charger and the batteries to a service shop.
the batteries will self-discharge! remove the battery from the charge as soon as it is fully charged.
general information on the battery: In the in­terests of ensuring that the battery has a long service life, pay attention to the following points:
• When the battery is at low voltage, the gardening tool
switches off automatically. In this case, the battery must be charged.
• The lithium ion battery must be charged before long
breaks in use, e.g. before winter storage.
• When the battery is fully discharged, charging time is 5
hours.
• The lithium ion battery can be charged whatever its cur-
rent state of charge, and charging can be interrupted at any time, without damaging the battery (there is no memory effect).
note: The battery is equipped with a deep-discharge pro­tection feature: the tool is automatically switched off if the battery is discharged. Recharge the battery immediately if this should be the case.
swItchIng the hedge trIMMer on/off
(g. 4)
When switching the hedge trimmer on take a safe stand. This hedge trimmer has a two-hand safety switch. To switch the hedge trimmer on the bar switch in the handle (A) must be pushed and the rotary switch of the handle (B) must be rotated by 45° backward. To switch the device off let go of both switches. The motor already stops if one of the two switches is released.
4
This hedge trimmer (8550) has an additional „Eco-switch“
feature (g. 5, D). This can vary the output in 2 steps.
High = higher performance, low = reduced performance. In the low position it will increase the battery time to about
twice the duration, while the speed of the hedge trimmer
tion of your apparatus, the batteries have to be taken from the apparatus, disposing of them separately. You can drop off your old batteries to the local collecting points of your municipality.
chargIng the BatterIes (g. 2 and 3)
caution! only use the charger in dry areas.
• To take out the battery, press both push-buttons on the sides designated with the number 1 and take out the battery (g. 2).
2
• Connect the battery charger to the socket. Make sure that the voltage stated on the battery charger matches the voltage in your socket.
• Connect the battery to the charger using the jack plug of the charger with the socket on the top of the battery (g. 3).
3
• Information on the charger:
- LED is red: Battery is charging
- LED is green: Charging complete
- LED is ashing alternatively red and green:
Fault (e.g. battery overheating)
• The period of charging the battery ranges from 3 to 5 hours. During the process of charging, the battery heats up. This is normal and it indicates no defect.
Page 10
Cordless Hedge Trimmer Operatorʼs Manual
7
For more freedom of movement where contour trimming is required the Swivel-Click™ handle can be set continu­ously, too. Depress the red lock button (C) and keep it pushed. The hedge trimmer can now comfortably be turned in all directions while working (Fig. 8).
8
To increase safety when operating the Swivel-Click™ han­dle, the trimmer drive shuts off in less that 0.1 seconds if either the switch on the hand grip (A) or the red switch rail on the turn handle (B) is released (Fig. 3). This ensures that the hedge trimmer can only be operated if both hands are on the hand grips and at the same time both switches are actuated. This effectively eliminates the risk of injury, combined with the extremely short run-on time.
holdIng the hedge trIMMer when In use (g. 9 and 10)
This equipment will enable you to cut or trim bushes and hedges easily and comfortably.
trimming of hedges
- Young shoots are best cut in a side-to-side movement.
- Older and stronger hedges are best cut in a sawing movement.
- Branches, which are too thick for the hedge trimmer, should be cut with a saw.
- Sides of hedges should be cut upwards in a taper.
is lowered. You can use this setting for lighter work to in­crease the battery life. On the back of the rear grab handle is the appropriate switch (g. 5).
5
adjustIng the swIVel-clIcK™ handle
(g. 6 - 8)
To facilitate work, the hedge trimmer features 3 preset pinlock positions (right, left, and normal). The purpose of this mechanism is that especially for cutting in a vertical direction the hedge trimmer can be held in their ergonomi­cally most favourable position whereby an early fatigue of the user is avoided.
Please proceed as follows to change the position of the handle:
6
Release switch (A). Pull back the locking pin (C) (Fig.
6). The handle is now unlocked and can be turned to the desired position (Fig. 6). Where consistent cuts are required, three preset pinlock positions allow the user to secure the handle and avoid an accidental change of positions (Fig. 7).
10
Page 11
Contact us at www.mantis.com
11
9
In order to achieve an even height
- Fix a guide line at the required height.
- Cut evenly over this guide line.
10
Take care to have a secure and safe standing posi­tion when working with your hedge shears in order to avoid slipping and injury. Always keep the shearing blades away from your body.
MaIntenance
always disconnect the battery from the tool be­fore commencing any work on the machine.
11
Important: Always clean and oil the blades after pro-
longed use of the hedge trimmer. This will greatly affect the life of the equipment. Damaged cutting units must be properly repaired immediately. Clean the shearing blades
with a dry cloth or – in case of heavier dirt – with a brush.
attention: danger of injury! Oiling of the blades should ideally be carried out using an environmentally friendly standard lubricant (Fig. 11). Make sure the unit is not run­ning during the cleaning process.
sharpening of the blades
The blades generally do not need servicing and do not require resharpening if used correctly. In order to prevent injuries caused by the blades when not in use, the sharp­ened cutting blade should be covered by the blade cover (Fig. 12). The blades cannot be sharpened by the user without opening the equipment and the safety mechanism. Resharpening of the blades can therefore only be carried out at a specialist workshop.
12
0.3" (8 mm)
changing the blades
Only correct installation of the blades will guarantee problem-free operation and function of the above men­tioned safety feature of the blades. Changing of the blades should therefore only be carried out at a specialist workshop.
optIMuM safetY
the 5 special features two-hand safety switch, quick blade stop, protective cover, blade safety rail and im-
pact protector are tted to provide the hedge trimmer
with optimum safety features.
attention!
If you nd out that safety functions, such as the
2-switch mechanism or the safety stop, are not functioning while working with the hedge trim­mer, immediately cease working and take the machine to a specialized shop for repairing.
two-hand safety switch (Fig. 4)
To switch the hedge trimmer on the bar switch in the handle (A) must be pushed and the rotary switch of the handle (B) must be rotated by 45° backward. To switch the device off let go of both switches. The motor already stops if one of the two switches is released.
Page 12
Cordless Hedge Trimmer Operatorʼs Manual
quick blade stop
In order to avoid injuries through cuts, the blade will stop in max. 0.1 sec. when one of the two switches is released.
Blade safety rail (Fig. 12) The cutting blade is set back by 0.32” (8mm) from the
passive blade teeth which prevents injuries due to unin­tentional body contact.
Impact protector (Fig. 12) The extended guide rail prevents unpleasant shocks
(blade recoil) being transmitted to the operator due to im­pact with solid objects (wall, ground etc.).
gear protection feature
If solid objects are caught in the cutting blade and jam the motor, switch off the machine at once, disconnect the bat­tery from the power tool, remove the object and continue with the work.
The equipment is also tted with an overload cutout, which
protects the gears against mechanical damage in the event of blade jams.
storIng the hedge trIMMer after use
the hedge shears must be stored such that there is no danger of injuries being caused to persons by the cutting blades!
Important note: The shearing blades should be cleaned
after each use.(see also Section Maintenance).This will considerably increase the service life of the device. Please use a lubricator that is not harmful to the environment. Then
put the shears in their case with the cutting blades rst.
enVIronMental protectIon
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and pack­aging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the rechargeable batteries are no longer required, they must be disposed of in an environ­mentally protective way . Run the battery complete­ly down and then remove it from the tool.
The rechargeable battery contain Lithium-ion (Li­ion). They are recyclable. Take them to your local recycling center to be disposed of properly. Do not incinerate Li-ion battery as they may explode
when exposed to re. Do not attempt to open the
battery packs.
12
Page 13
Page 14
MANTIS extends this limited warranty against defects in material and workmanship for a period of two (2) years from the date of purchase by the original purchaser.
MANTIS will repair or replace, at its option, any part or parts of the product found to be defective in material or workmanship during the warranty period. Warranty repairs and replacements will be made without charge for parts or labor. All parts replaced under warranty will be considered as part of the original product, and any warranty on the replaced parts will expire coincident with the original product warranty . If you think your MANTIS ElEcTrIc chAINSAW is defective in material or workmanship, you must send it, along with your proof of purchase (sales receipt) to:
Mantis 1028 Street road Southampton, PA 18966
You are responsible for pickup and delivery charges; the product must be returned to us postage paid. MANTIS assumes no responsibility in the event that the product was not assembled or used in compliance
with any assembly, care, safety, or operating instructions contained in the Owner’s Manual or accompanying the product. This limited warranty does not cover damages or defects due to normal wear and tear, lack of reasonable and proper maintenance, failure to follow operating instructions or owner’s manual, misuse, lack of proper storage or accidents [or routine maintenance parts and service]. This limited warranty shall not be effective if your MANTIS ElEcTrIc chAINSAW has been subjected to negligence or has been repaired or altered by anyone other than an authorized dealer or authorized service center.
You must maintain your MANTIS ElEcTrIc chAINSAW by following the maintenance procedures described in the owner’s manual. Such routine maintenance, whether performed by you or a dealer, is at your expense.
MANTIS MAKES NO EXPrESS Or IMPlIED WArrANTIES, rEPrESENT A TIONS Or PrOMISES EXcEPT ThOSE cONTAINED hErEIN. ThErE ArE NO OThEr WArrANTIES, INclUDING WArrANTIES OF MErchANT ABIlITY AND FITNESS FOr A PArTIcUlAr PUrPOSE. All WArrANTIES OThEr ThAN ThE EXPrESS WArrANTY SET FOrTh ABOVE ArE SPEcIFIcAllY DISclAIMED. ThE DUrATION OF ANY IMPlIED WArrANTY, INclUDING MErchANTABIlITY AND FITNESS FOr A PArTIcUlAr PUrPOSE, IS lIMITED TO ThE DUrATION OF ThIS WrITTEN lIMITED WArrANTY. MANTIS DISclAIMS All lIABIlITY FOr INDIrEcT, INcIDENTAl AND/Or cONSEQUENTIAl DAMAGES IN cONNEcTION WITh ThE USE OF ThE MANTIS PrODUcTS cOVErED BY ThIS WArrANTY. SOME STATES DO NOT AllOW lIMIT A TIONS ON hOW lONG AN IMPlIED WArrANTY lASTS AND/Or DO NOT AllOW ThE EXclUSION Or lIMITATION OF INcIDENTAl Or cONSEQUENTIAl DAMAGES, SO ThAT ABOVE lIMITATIONS AND EXclUSIONS MAY NOT APPlY TO YOU. ThIS WArrANTY GIVES YOU SPEcIFIc lEGAl rIGhTS, AND YOU MAY AlSO hAVE OThEr rIGhTS WhIch VArY FrOM STATES TO STATE.
Specications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to
change without notice.
©
2013 Schiller Grounds care, Inc. All rights reserved. P/N 401786
Page 15
Page 16
Loading...