MantaroBot TableTop TeleMe Quick Start Manual

MANTAROBOT™ TABLETOP TELEME

Assembly Instructions &

Quick Start Guide

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

Table of Contents

Table of Contents .......................................................................................................................................... 2

Assembly Instructions ................................................................................................................................... 3

Assembly without Floor Base and Mast Extension ................................................................................... 4

Assembly with Floor Base and Mast Extension ........................................................................................ 7

Installing User Device .............................................................................................................................. 12

Quick Start (when using Android tablets) ................................................................................................... 15

Quick Start (for TableTop TeleMes with WiFi option) ................................................................................ 22

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

2

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

Assembly Instructions

1. Carefully unpack the contents in which your TableTop TeleMe was shipped. DO NOT throw

away the shipping materials. Store them safely so they can be used to ship or transport your
TableTop in the future.

2. Identify the parts in the picture below. The only tool required to assemble your TeleMe is a #1

Phillips screwdriver. Parts D, E, and F are only included if you purchased the Floor Base with
Mast Extension option. Part G (not shown below) is the optional battery module installed in the
base of Part A.

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

3

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

Assembly without Floor Base and Mast Extension

1. Protruding from bottom of device holder (B) is a male connector. Protruding from top of base

pole (A) is a female connector. Plug male connector from device holder (B) into female
connector of base pole (A). See picture below.

2. Slide pole of device holder (B) all the way down

over the base pole (A) while aligning the two screw
holes in both (A) and (B).

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

4

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

3. Using a #1 Phillips screw driver, screw two of the provided screws (C) into the pole of device

holder (B) to secure it to base pole (A).

4. Plug in the supplied AC/DC power adapter to the connector located in the cavity on the

underside of the TableTop base. Plug the other end of the power supply cord to a wall outlet.

5. If the optional internal battery option was purchased it was already shipped installed into your

unit. However, the battery was disconnected for shipping. Remove the two screws holding the

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

5

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

rectangular shaped battery module on the underside of the base. Slide the battery module out,
connect the wire connector from the battery module to the wire connector inside the
compartment, and then slide the battery module back in. Put the two screws back holding the
battery module in place.

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

6

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

Assembly with Floor Base and Mast Extension

1. If the optional internal battery option was purchased it was already shipped installed into your

unit. However, the battery was disconnected for shipping. Remove the two screws holding the
rectangular shaped battery module on the underside of the TeleMe base (A). Slide the battery
module out, connect the wire connector from the battery module to the wire connector inside
the compartment, and then slide the battery module back in. Put the two screws back holding
the battery module in place.

2. Align the feet of TeleMe base (A) with holes in the Floor Base (F) as shown in the picture below.

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

7

MantaroBot™

Phone [phone]  Fax [phone]

MANTAROBOT TABLETOP TELEME

Assembly Instructions &
Quick Start Guide

Using thumb screw (E) attach the Floor base to the TeleMe base as shown below.

20410 Century Boulevard  Suite 120  Germantown Maryland 20874

www.MantaroBot.com  [e-mail]

8

MantaroBot™

Phone [phone]  Fax [phone]