Manrose CLASSIC PRO Instructions Manual

CLASSIC SERIES

INSTALLATION INSTRUCTIONS

Fixing clip

Ceiling board

Screw

Fan
chassis

When screw is tightened fixing
clip fingers secure the fan

MANROSE 125MM EXTRACT-A-LITE DIFFUSER
CLASSIC AND PRO SERIES

Thank you for selecting our Manrose 125mm Extract-a-Lite Diffuser.

Please read all instructions before commencing installation.

Please ensure the corrrect LED lamp and driver OR Halogen lamp and transformer are used for
replacements. The LED model MUST be replaced with an LED lamp and the Halogen model MUST be
replaced with a Halogen lamp. They are not interchangeable.

We reserve the right to change specification without prior warning

Light Specifications:

Clasic LED models: DCT3206 and DC3207
(including driver)

Pro Series LED models: DCT3213 and DCT3214
(including driver)

Driver Input: 220-240 VAC

Driver Output: 12VDC

Lamp MR16: 12V / 3W high power LED, 250 beam
angle

Classic Halogen models: DCT2120 and
DCT2121 (excluding transformer)

Pro Series Halogen models: DCT1519 and
DCT1520 (excluding transformer)

Transformer Input: 220-240 VAC

Output: 12VAC

Lamp MR16: 12V / 50W Halogen, 600 beam angle

Diagram 1
INSTALLATION

PRO SERIES
DIMENSIONS

165mm

80mm

115mm

CLASSIC
DIMENSIONS

165mm

118mm

80mm

Manrose is proudly distributed by Simx Limited
PO Box 14 347, Panmure, Auckland, NZ. Technical Support [phone]
e: [e-mail] | www.simx.co.nz | www.manrose.com.au

PUB0329 iss:03 10/13

Diagram 2
TYPICAL INSTALLATION

Flexible duct

Internal
Extract-a-Lite

The Shower Fan
screwed to the joist

Installation Instructions

1. The Extract-a-Lite is suitable for any 125mm in line extractor system including Passive Stack Ventilation
systems (see overleaf for installation example).

Important: The Halogen model Extract-a-Lite must not work independently of the fan.

2. Cut a 140mm-diameter hole in ceiling, affix the chassis using the 4 holes. (Always ensure the hole is
cut between ceiling rafters). Use the fixing clips to secure the fan to the wall or ceiling. (See diagram 1).

3. Connect the duct to the spigot of the chassis.

4. For the LED models: Connect a suitable driver to the Extract-a-Lite and to a suitable power
supply, ideally to the switched live of the extractor fan installed. Recommended driver: FAN5342.
Replacement lamp: LHT0221

For the Halogen models: Connect a suitable transformer to the Extract-a-Lite and to a suitable
power supply, ideally to the switched live of the extractor fan installed. Recommended transformer:
FAN2101. Recommended lamp: FAN0431

5. Place the ceiling cover onto the chassis by locating onto the 3 lugs, and twisting clockwise.

6. Never connect mains direct to the lamps.

7. The transformer/driver must be suitable for 230V AC input.

CAUTION: Disconnect the power supply, and be sure that the lamp has fully cooled before removing
or replacing.

IMPORTANT

External Grille

• Isolate the mains supply before making any electrical connections. This system should be
installed by a qualified electrician.

• When fitting through an external wall, an external grille must be fitted at all times.

• Fan should only be installed by fixed wiring, a flexible cord should not be used.

• The appliance is not intended for use by young children or infirm persons without supervision.

• Young children should be supervised to ensure that they do not play with the appliance.

• Precautions must be taken to avoid the back-flow of gases into the room from the open flue

of gas or other open-fire appliances when mounted in outside windows or walls.