Manning Systems HA71 Data sheet

HA20, HA40 & HA71 SPECIFICATIONS

Gas Detection Controllers

HA20 and HA40 Models

General Specifications

Use Wall or rack/panel mountable digital gas controller for industrial or commercial use

Display 128 x 64 pixel graphic LCD with backlight displays, bar graphs, trends and engineering units

Common Alarm Relays (STANDARD) Two, 5 amp 30VDC or 250VAC resistive Form C

Discrete Alarm Relays (OPTIONAL) Six 5 amp 30VDC or 250VAC resistive Form C

Analog Output (OPTIONAL) 10 bit 4-20mA output. Max load 800 ohms with nominal 24VDC power supply.

Serial Port (OPTIONAL) Slave RS-485 port equipped with Tx / Rx LED’s

Power Requirement 100-240 VAC / 24 VDC are standard primary power supplies

Operating Temperature Range (-25 °C to +50 °C)

Housing Options NEMA 4X / IP66 wall mount approved for Div 2

NEMA 7 explosion-proof wall mount Div 1 & 2
NEMA 4X SS Enclosure wallmount approved for Div 2

Weight NEMA 4 = 5 pounds, NEMA 7 = 40 pounds

Warranty 2 Years Limited

HA20 & HA40 Wireless Options

Use An optional HA40 900MHz wireless interface (10-2454) can be used to communicate with an HA71 master Modbus controller.

Ratings and Certifications

Certified to CSA C22.2 No. 1010.1 & ISA S82.02; UL 1604 / C22.2 No 213 (NEMA 4X = Div 2 Groups A, B, C, D, NEMA 7 =

Protocol = Modbus RTU

An additional 900MHz wireless adapter is also required for the HA71 (10-0288).

Groups B, C, D); EN55011 & EN61000.

HA71 Model

General Specifications

Use Wall or rack/panel mountable digital gas controller for industrial or commercial use

Size 15 1/8” (H) x 13 1/7” (L) x 9 1/16” (D)

Weight 17 lbs. (wallmount enclosure); 7 lbs. (rackmount enclosure)

Power Requirement 10-30VDC (24VDC nominal) 12 watts max

Analog Inputs (optional) 12 bit 4-20mA into 100 ohms input impedance; includes +power supply terminals for each channel for routing power to 2 or 3 wire transmitters

Serial Ports Master & Slave RS-485 half or full duplex ports equipped with Tx/Rx LED’s. Protocol = Modbus RTU

Common Alarm Relays 5 amp 30VDC or 250VAC resistive Form C

Discrete Alarm Relays (optional) 5 amp 30VDC or 250VAC resistive Form C

Analog Outputs (optional) 10 bit 4-20mA output. Max. load 800 ohms with nominal 24VDC power supply

Display 128 x 240 pixel graphic LCD with backlight displays bar graphs, trends and engineering units;

Operating Temperature Range -13°F to 140°F (-25°C to 60°C)

Housing Options NEMA 4X fiberglass wall mount (shown below, left); ½ length 19 inch rack/panel mount (shown below, right); NEMA 7 explosion-proof wallmount (see manual)

Approvals CSA C22.2 No. 1010.1 & 152 for combustibles & ISA S82.02; UL 1604/C22.2 No. 213 Div 2 Groups A,B,C,D); EN55011 & EN61000

Ratings and Certifications

Certified to CAN/CSA C22.2 No. 61010-1

Conforms to ANSI/UL 61010-1

Find out more

www.honeywellanalytics.com
Toll-free: 800.538.0363

Please Note:

While ever effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions.
Data may change, as well as legislation, and you are strongly advised to obtain copies of the most recently issued regulations,
standards, and guidelines. This publication is not intended to form the basis of a contract.

© 2010 Honeywell Analytics

52 discrete LED’s indicate alarm status for 3 alarms per 16 channels and common relays