Manitowoc Ice 20308-130 Installation Manual

Installation For

Model 20308-130

Auto Shutoff Valve Replacement

Model 20308-130 Auto Shutoff Valve

OUT IN

PRODUCT

IN

OUTGAS

TO VENT CO2

DISCHARGE

INSTALL HOSE

TO GAS OUT

20 ICON, FOOTHILL RANCH, CA

P/N 1521-000

P/N 1520-000

P/N 20608-100

P/N 20607-100

P/N 20606-100

P/N 20324-30

P/N 1510-000

Flojet Brass CO

2

Inlet Shutoff Valve

Assemblies

Optional Stainless Steel

Product Out Barb Ports

Standard

Product Out

Barb Port

3/8" (9.5 mm)

P/N 20325-030

Slide

Retainer

Clip

Slide

Retainer

Clip

1/4"

(6.3 mm)

1/4"

(6.3 mm)

1/4"

(6.3 mm)

1/4"

(6.3 mm)

3/8"

(9.5 mm)

1/2"

(12.7 mm)

1/4"

(6.3 mm)

ONE YEAR LIMITED WARRANTY

FLOJET warrants this product to be free of defects in material and/or workmanship
for a period of one year after purchase by the customer from FLOJET. During this
one year period, FLOJET will at its option, at no charge to the customer, repair or
replace this product with a new or reconditioned product, but not remove or install,
in the event that it is found to be defective in material and/or workmanship.

This Limited Warranty does not include service to diagnose a claimed malfunction
in this product at any location other than at Flojet’s corporate head-quarters, nor to
repair damage due to improper installation, incompatibility with accessories not
manufactured by FLOJET, external electrical fault, accident, or misuse.

All other express and implied warranties for this product including the warranties of
merchantability and fitness for a particular purpose, are hereby disclaimed. The
product covered by this warranty is marketed and sold by FLOJET as a business
rather than consumer product. (Some jurisdictions do not allow the exclusion of
implied warranties nor limitations on how long an implied warranty lasts, so the
above limitations may not apply to you.)

If this product is not free of defect as warranted above, your sole and exclusive
remedy shall be repair or replacement as provided herein. In no event will FLOJET
be liable to customer or to any third party for any damages in excess of the
purchase price of the product. This limitation applies to damages of any kind
including any direct or indirect damages, lost profits, lost investment capital or
savings, or other special, incidental, tort or otherwise, or whether arising out of the
use or inability to use such product even if FLOJET has been advised of the
possibility of such damages or of any claim by any other party. (Some jurisdictions
do not allow the exclusion or limitation of incidental or consequential damages for
some products, so the above limitations or exclusions may not apply to you.)

This warranty gives you specific legal rights. You may also have other rights which
may vary from jurisdiction to jurisdiction

.

© Copyright 2001, ITT Industries Printed in U.S.A. All Rights Reserved Form: 81000-049 11/01

UNITED KINGDOM
Flojet, Unit 1, Avant Business Centre
Denbigh West Industrial Estate
Milton Keynes, Bucks, England MK1 1DL
Tel: [phone]
Fax: [phone]

U.S.A.
Flojet
20 Icon
Foothill Ranch, CA 92610-3000
Tel: [phone]
Fax: [phone]

STEP NO. 1

Turn off CO2supply and open dispensing valve to
relieve syrup pressure. Disconnect product IN line.

STEP NO. 2

Move lock on CO2fitting and unplug from Auto Shutoff
valve. With a small screwdriver locate the slide retainer
clips on the bottom of the pump under the Auto Shutoff
valve. There are two (2), one on each side of the valve.
(See figure #1). Insert screwdriver and push clips as far
as they will go, away from the valve. The Auto Shutoff
valve can be removed without tools. Simply pull the
valve from the pump base.

STEP NO. 3

Insert new valve. Push valve into pump base as far as it
will go, slide clips in and “snap” into place. Plug in CO

2

connection and secure retainer clips.

STEP NO. 4

Reconnect product IN line and reset CO2pressure to
normal operating level. Make sure bag connector is fully
engaged.

STEP NO. 5

Pump should come on and pressurize syrup line. To test
Auto Shutoff valve, remove bag connector and open
dispensing valve, pump should shut off automatically.
Replace bag connector and pump should operate
normally when valve is opened.