Manitowoc FRP-250, FRP-250SCI User Manual

Download

Flav’R-Pic Series Selectable Ice /

Beverage Dispensers

Installation, Use & Care Manual

This manual is updated as new information and models are released.

Visit our website for the latest manual. www.manitowocfsg.com

Leader in Ice & Beverage Dispensers

Part Number 020003315 1/11

Safety Notices

! Warning

Caution

Important

Caution

Important

! Warning

As you work on Manitowoc equipment, be sure to pay close attention to the safety notices in this manual. Disregarding the notices may lead to serious injury and/ or damage to the equipment.

Throughout this manual, you will see the following types of safety notices:

Text in a Warning box alerts you to a potential personal injury situation. Be sure to read the Warning statement before proceeding, and work carefully.

Text in a Caution box alerts you to a situation in which you could damage the equipment. Be sure to read the Caution statement before proc eeding, and work carefully.

Procedural Notices

As you work on Manitowoc equipment, be sure to read the procedural notices in this manual. These notices supply helpful information which may assist you as you work.

Throughout this manual, you will see the following types of procedural notices:

Read These Before Proceeding:

Proper installation, care and maintenance are essential for maximum performance and troublefree operation of your Manitow oc equipment. Read and understand this manual. It contains valuable care and maintenance information. If you encounter problems not covered by this manual, do not proceed, contact Manitowoc Foodservice Group. We will be happy to provide assistance.

Routine adjustments and maintenance procedures outlined in this manual are not covered by the warranty.

PERSONAL INJURY POTENTIAL

Do not operate equipment that has been misused, abused, neglected, damaged, or altered/modified from that of original manufactured specifications.

NOTE: SAVE THESE INSTRUCTIONS.

Text in an Important box provides you with information that may help you perform a procedure more efficiently. Disregarding this information will not cause damage or injury, but it may slow you down as you work.

NOTE: Text set off as a Note provides you with simple, but useful, extra information about th e pr oce dur e yo u are performing.

We reserve the right to make product improvements at any time.

Specifications and design are subject to change without notice.

Section 1 General Information

Read This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Unit Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Model Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Section 2 Installation Instructions

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

FRP-250 Footprint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Location Requirements for Top Mounted Ice Machine Installations. . . . . . . . 2-3

Pre-installation Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

How To Read A Model Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Baffle for Manitowoc

Manual Fill Lid - Dispensers with an Ice Machine . . . . . . . . . . . . . . . . . . . . 1-1

Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Pre-mix System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

B-I-B System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Post Mix System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Figal System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

BULK SYRUP SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Double Check: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Also Consider The Location Of The Following Items Before Installation: . . 2-5

Additional Checks for Top Mounted Ice Machine Installations . . . . . . . . . . 2-5

Baffle for Ice Machine Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

“S” Series Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

"Q" Series Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Minimum Circuit Ampacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Minimum Circuit Amperage Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Ice Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Pump Deck Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Wat er Suppl y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Recommended Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Diagram Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

FRP-250 Plumbing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

CO2 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Routing Internal Carb Tank Purge Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Drains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Step by Step Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Specifications Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

System Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Brixing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

General Brixing Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

NOZZLE 1 (N1) WATER AND SYRUP BRIXING . . . . . . . . . . . . . . . . . . . . 2-15

NOZZLE 2 (N2) WATER AND SYRUP BRIXING . . . . . . . . . . . . . . . . . . . . 2-15

NOZZLE 3 (N3) CARB/NON-CARB WATER & SYRUP BRIXING . . . . . . . 2-15

NOZZLE 4 (N4) CARB/NON-CARB WATER & SYRUP BRIXING . . . . . . . 2-15

NOZZLE 5 (N5) WATER AND SYRUP BRIXING . . . . . . . . . . . . . . . . . . . . 2-16

NOZZLE 6 (N6) WATER AND SYRUP BRIXING . . . . . . . . . . . . . . . . . . . . 2-16

Starting Your Beverage System & Dispenser. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Section 3 Operation

General System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Sequence of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Ice Recommended for Dispensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Ice Storage and Dispensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Beverage Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Rocking Chute Ice Dispensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Selectable Ice Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Carbonation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Syrup Delivery System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Back Room Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Racking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

B-I-B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Auto Bag Selectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

FRP-250 Non-Adjustable Agitation Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

FRP-250SCI Non-Adjustable Agitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Control Box Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Operation Checks and Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

FRP-250 (non-Ice Crushing Unit) Ice Delivery Switch Adjustment . . . . . . . 3-5

EXTERNAL BRIX MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

How to Check FRP Brix Externally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

CRUSHED OR CUBED DEFAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

How to set default ice dispense setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

CUBE DEFAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

CRUSH DEFAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

LAST SELECTION DEFAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Carb/Non-Carb & Flavor Shot Duration Settings . . . . . . . . . . . . . . . . . . . . 3-7

N3 & N4 Carbonated or Non-Carbonated Drinks . . . . . . . . . . . . . . . . . . . . 3-7

Flavor Shot Dispense Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

PROGRAM MODE 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Brixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

PROGRAM MODE 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Light Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

CONTROL BOARD TIME OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

NOZZLES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

FRP-250 & FRP-250SCI Tubing Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Control Logic Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Control board, Valve, Touch pad Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

ADA Touch Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

ADA Touch Pad Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Section 4 Maintenance

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Daily Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Monthly Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Cleaning Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Disassembly for Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 4-3

FRP-250 (Non-Crusher) Disassemble the Rocking Chute . . . . . . . . . . . . . 4-4

Selectable Ice Crusher Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

reassemble the Ice Crusher assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Serviceable Gear Motor Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Sanitizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Shipping, Storage and Relocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

FRP-250 Graphic Medallion Removal & Installation . . . . . . . . . . . . . . . . . . . . . 4-10

Section 5 Before Calling for Service

Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Drink Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Flavor Shot Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Pump Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Table of Contents

Beverage System Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Bag-In-Box System Sanitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Figal Beverage System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Medallion Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Medallion Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Selectable Ice Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Part Number 020003315 1/11 4

Section 1 General Information

Warning

S = Ice Only SV = Ice/Beverage NGF = Ice/Beverage FRP = Ice/Beverage & Integrated Flavor Shots

i = Intellicarb QD = Quickdraw SCI = Ice Crusher

Ice Capacity

Model Prefix

Model Suffix

Model Base

SV–250–i

Section 1

General Information

Read This Manual

Manitowoc Beverage Equipment (MBE) developed this manual as a reference guide for the owner/oper ator a nd installer of this equipment. Please read this manual before installation or operation of the machine. A qualified service technician must perform inst allation and start-up of this equipment, consult Section 5 within this manual for service assistance.

If you cannot correct the service problem, call your MBE Service Agent or Distributor. Always have your model and serial number available when you call.

Your Service Agent ____________________________ Service Agent Telephone Number_________________ Your Local MBE Distributor ______________________ Distributor Telephone Number____________________ Model Number _______________________________ Serial Number ________________________________ Installation Date ______________________________

Unit Inspection

Thoroughly inspect the unit upon delivery. Immediately report any damage that occurred during tr ansportation to the delivery carrier. Request a written inspection report from a claims inspector to document any necessary claim.

PERSONAL INJURY POTENTIAL

Do not operate equipment that has been misused, abused, neglected, damaged, or altered/modified from that of original manufactured specifications.

Model Numbers

This manual covers the following models:

Beverage/Ice Dispensers

FRP-250, FRP-250SCI

HOW TO READ A MODEL NUMBER

Accessories

BAFFLE FOR MANITOWOC® ICE MACHINE

When installing a Manitowoc Ice Machine on a dispenser, a baffle kit is required for proper installation. The baffle kit is designed to prevent ice from lying against the front of the ice machine, and melting down the front of the dispenser. There are two different baffle kits available for “S” series ice machines, one kit is for the 30" wide machine, and the other kit is for the 22" wide machine. There is also a kit for “Q” series ice machines.

Kits are available through your local distributor. List prices may be subject to change without notification. Please call your local parts distributor for current pricing before ordering.

Part Number 020003315 1/11 1-1

MANUAL FILL LID - DISPENSERS WITH AN ICE MACHINE

If you are top mounting your dispenser with a ice machine, you will require a lid for the manual fill area at the top, front of the dispenser.

If you ordered a dispenser and a ice machine at the same time, the manual fill lid was included with the unit. The manual fill lid can be ordered from your local distributor.

General Information Section 1

Label

LEGS

Legs are optional equipment with most MBE dispen sers. Sta ndard legs a re 4" ( 10.2 cm) t a ll st ainless stee l legs. If an ice machine is installed on top of the dispenser, legs must not be installed. We do not recommen d using legs when an ice machine is mounted on the dispenser. The combined weight of the dispenser , ice and ice machine is more evenly distributed when the base area of the dispenser is in contact with the counter top.

Serial Number Location

This number is required when requesting information from your local distributor. The serial number is listed on the SERIAL NUMBER DECAL affixed to the dispenser.

Warranty Information

Consult your local MBE Distributor for terms and conditions of your warranty. Your warranty specifically excludes all beverage valve brixing, general adjustments, cleaning, accessories and related servicing.

Your warranty card must be returned to MBE to activate the warranty on this equipment. If a warranty card is not returned, the warranty period can begin when the equipment leaves the MBE factory.

No equipment may be returned to MBE without a written Return Materials Authorization (RMA). Equipment returned without an RMA will be refused at MBE’s dock and returned to the sender at the sender’s expense.

Please contact your local MBE distributor for return procedures.

Serial Number Location

1-2

Part Number 020003315 1/11

General

Important

Section 2

Installation Instructions

These instructions are provided to assist the qualified installer. Contact your Manitowoc Beverage Equipment Service Agent or call Manitowoc Beverage Equipment for information regarding start-up service s.

Dimensions

Failure to follow these installation guidelines may affect warranty coverage.

FRP-250 A B C D E F G H I

250* 39.81"

(101.1 cm)

* Includes FRP-250SCI

Part Number 020003315 1/11 2-1

30.00"

(76.2 cm)

9.94"

(17.6 cm)

4.44"

(1 1.3 cm)

22.63"

(57.5 cm)

28.00"

(71.1 cm)

31.13"

(79.1 cm)

20.00"

(50.8 cm)

27.44"

(69.7 cm)

Installation Instructions Section 2

Minimum Area

for Cutout

Maximum Area

for Cutout

Caution

FRP-250 Footprint

Flav’R-Pic

250* 26.00"

ABCD

(66.0 cm)

Cutting the countertop may decrease its strength. Counter must be braced to support the dispenser countertop weight plus ice storage capacity and weight of icemaker, if applicable.

Maximum Minimum

17.81"

(45.2 cm)

4.00"

(20.30 cm)

24.00"

(61.00 cm)

2-2

Part Number 020003315 1/11

Section 2 Installation Instructions

Warning

Location

The location selected for the beverage dispenser must meet the following criteria. If any of these criteria are not met, select another location.

• The air temperature must be at least 50°F (10°C), but must not exceed 95°F (35°C).

• The location must not be near heat-generating equipment or in direct sunlight and must be protected from weather.

• The countertop must be level. Verify that the countertop can support the weight of the dispe ns er, or the dispenser/ice machine combination plus the weight of the stored ice.

• Water lines, drains and power outlet must be within 6' (1.8 m) of location.

Carbon Dioxide (CO2) displaces oxygen. Exposure to a high concentration of CO which are followed rapidly by loss of con sciousness and suffocation. If a CO particularly in a small area, immediately ventilate the area before repairing the leak. CO must not be installed in an enclosed space. An enclosed space can be a cooler or small room or closet. This may include convenience stores with glass door self serve coolers. If you suspect CO may build up in an area, venting of the B-I-B pumps and / or CO

monitors must be utilized.

gas causes tremors,

gas leak is suspected,

lines and pumps

Location Requirements for T op Mounted Ice Machine Installations

Location — Avoid placing the dispenser and/or ice

machine near heat sources such as radiators, ovens, refrigeration equipment and direct sunlight.

Clearances — Refer to the ice machine installation manual for clearances.

Front of ice machine to be flush with front of dispenser — Some ice machines may overhang at the

back of the dispenser. Drains — A separate drain line is required for the ice

machine, in addition to a drain line for the ice/beverage dispenser.

Dispensers may require an adapter kit to install some top-mounted ice machines. Contact your local distributor for the correct adapter kit.

For full information about ice machine installation, including clearances, plumbing lines, connections, and electrical requirements, see the ice machine installation manual.

Part Number 020003315 1/11 2-3

Installation Instructions Section 2

Pre-installation Checklist

When installing any system, first make sure the major components are available. Generally the major components necessary for an installation are:

PRE-MIX SYSTEM

regulator set

Product connectors for Figal tank

Gas connectors for Figal tank

Beverage dispenser

Beverage tubing

tank

Figal beverage tanks

POST MIX SYSTEM

CO2 regulator set

Beverage dispenser

Beverage tubing

tank

Carbonator

Stepless (Oetiker) clamps

Chain for CO

tank

Stepless (Oetiker) clamps

Chain for CO

B-I-B SYSTEM

B-I-B connectors

B-I-B regulator set

B-I-B rack

B-I-B syrup boxes

tank

FIGAL SYSTEM

Syrup connectors for Figal tank

Gas connectors for Figal tank

Figal syrup tanks

BULK SYRUP SYSTEM

Syrup connectors for Bulk tank

Gas connectors for Bulk tank

Bulk syrup tanks

2-4

Part Number 020003315 1/11

Section 2 Installation Instructions

(15.2 cm)

DOUBLE CHECK:

Do you have enough space to install the dispenser or a dispenser and top mounted ice machine?

Does top mounted ice machine (if utilized) have a minimum of 6 inches (15.3 cm) clearance on all sides?

Is the countertop level?

Can the countertop support the weight of the dispenser, or the dispenser/ice machine combination plus the weight of the stored ice?

ALSO CONSIDER THE LOCATION OF THE FOLLOWING ITEMS BEFORE INSTALLATION:

Water line

Drain

ADDITIONAL CHECKS FOR TOP MOUNTED ICE MACHINE INSTALLATIONS

Location — Avoid placing the dispenser and/o r

ice machine near heat sources such as radiators, ovens, refrigeration equipment and direct sunlight.

Clearances — Six inch (15.2 cm) clearance on all sides of the icemaker is needed.

Front of icemaker to be flush with front of dispenser — The front of the icemaker must be

flush with the front of the dispenser. When the icemaker is flush with the front of the dispenser, some icemakers may overhang at the back of the dispenser.

Drains — A separate drain line is required for the ice machine, in addition to a drain line for the ice/beverage dispenser.

Dispensers may require an adapter kit to install some top-mounted icemakers. Contact your local distributor for the correct adapter kit.

Power outlet

Heating and air conditioning ducts

For full information about icemaker installation, including plumbing lines connections and electrical requirements, see the icemaker installation manual.

Part Number 020003315 1/11 2-5

Installation Instructions Section 2

Backing Plate to Be Inserted

Into Side Pocket of Bulkhead

Screws

New Ice Baffle

Backing Plate

to Be Inserted

Into Side Pocket of Bulkhead

Baffle, Manitowoc Ice

Machine

0.69"

(1.7 cm)

Ref.

6.32"

(16.0 cm)

Ref.

7.22"

(18.3 cm)

Ref.

Assembly

BAFFLE FOR ICE MACHINE INSTALLATIONS “S” Series Baffle

1. Remove both front panels.

2. Examine the ice machine to see if the machine has four screws on the lower front plastic panels.

3. If there are screws, remove the m from the countersunk holes on the front surface of the machine, save the screws.

4. Install the deflector, using the four screws removed in step three.

5. Four screws and two backing plates are in the kit.

6. If there are no screws on the ice machine (step 2), pierce the thin plastic countersunk holes, install the backing plates and install the deflector using the screws from the kit.

7. Replace the front panels.

"Q" Series Baffle

1. Position baffle on top of water well with tab on the front and the other tab inside the water well.

2. Mount the baffle on the left side of the ice machine using the hole and screw provided.

"Q" Series Ice Machine

"S" Series Ice Machine

2-6

Part Number 020003315 1/11

Section 2 Installation Instructions

Warning

Important

Warning

Electrical

GENERAL

All wiring must conform to local, state and national codes.

MINIMUM CIRCUIT AMPACITY

The minimum circuit ampacity is used to help select the wire size of the electrical supply. (Minimum circuit ampacity is not the beverage/ice machine’s running amp load.) The wire size (or gauge) is also dependent upon location, materials used, length of run, etc., so it must be determined by a qualified electrician.

ELECTRICAL REQUIREMENTS

Refer to Ice Machine Model/Serial Plate for voltage/ amperage specifications.

VOLTAGE

The standard voltage for FRP-250 Series dispensers is 120VAC-60Hz. A power cord is provided with 120VAC60Hz models only . FRP-250 Series dispe nsers use a 1/7 hp gearmotor.

MINIMUM CIRCUIT AMPERAGE CHART

Due to continuous improvements, this information is for reference only. Please refer to the dispenser serial number tag to verify electrical data. Serial tag information overrides information listed on this page.

Grounding Instructions

Risk of electrical shock. Connect to a properly grounded outlet only.

This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Improper connection of the equipment-ground ing conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor. If repair or replacement of the cord or plug is neces sary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance — if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Dispenser Voltage/Cycle

FRP-250, FRP-

250SCI

Part Number 020003315 1/11 2-7

115/60 2.8

220/50, 220/60,

240/50, 240/60

220-240/50 5

Minimum

Circuit Amps

1.5

(with carb deck)

Installation Instructions Section 2

Warning

PUMP DECK WIRING

The supply cord is equipped with a three prong 5-15P.

When using electric appliances, basic precautions should always be followed, including the following:

a. Read all the instructions before using the

appliance.

b. To reduce the risk of injury, close

supervision is necessary when an

appliance is used near children. c. Do not contact moving parts. d. Only use attachments recommended or

sold by the manufacturer. e. Do not use outdoors.

f. For a cord-connected appliance, the

following shall be included:

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Unplug from outlet when not in use and before servicing or cleaning.

• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped or damaged in any manner. Contact the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.

g. For a permanently connected appliance —

Turn the power switch to the off position when the appliance is not in use and before servicing or cleaning.

h. For an appliance with a replaceable lamp —

Always unplug before replacing the lamp. Replace the bulb with the same type.

When a Ground Fault Circuit Interrupter (GFCI) is required by code, a breaker type protector must be used. We do not recommend GFIC outlets as they are known for more intermittent nuisance trips than panel breakers. To ensure both the safety and proper operation of this equipment, be certain th at the electrical receptacle is a proper design so as to accept this plug, ensuring that the carbonator assembly is properly grounded.

If the pump deck is to be installed in an area or community whose local codes require permanent wiring, the following procedure must be followed.

1. The three wires (white, black and green) must be fed through the cable connector and brought into the wiring compartment. The cable must be secured into the connector.

2. The green wire from the cable must be connected to the green screw that attaches to the inside panel of the wiring compartment. Be sure to use a ring torque terminal for connecting the wire to the screw.

3. The white wire from the cable must be joined to the N terminal of the liquid level control board by a suitable U.L. listed insulated cable connector.

The black wire from the cable must be joined to the L1 terminal of the liquid level control board by a suitable U.L. listed insulated cable connector.

i. For a grounded appliance — Connect to a

properly grounded outlet only. See Grounding Instructions.

2-8

Part Number 020003315 1/11

Section 2 Installation Instructions

Splash Panel

Plumbing Diagram

Water Supply

RECOMMENDED PLUMBING

The plumbing diagram is printed on a white vinyl label, normally located above the inlet tubes for syrup and water. The plumbing diagram label can be accessed by removing the splash panel of the dispenser. The plumbing diagram label explains which inlet coldplate fittings supply which dispenser valves and water manifolds.

The water supply must first be connected to the carbonator pump (not shown) before plumbing to connection “A” shown on plumbing diagram. The carbonator pump deck must be within six feet of the dispenser for optimum performance. See BIB inst allation diagram for system pressure settings.

A check valve must be installed in the water supply line 3 feet from the noncarbonated water connect ion “PW”. Contact factory if not installed.

DIAGRAM LOCATION

Part Number 020003315 1/11 2-9

Installation Instructions Section 2

C1 / C2/ NC2

S1-S8 / F1-F4

C3 / C4/ NC3

S9-S16 / F5-F8

CONTROL BOARD

LEFT SIDE

CONTROL BOARD

RIGHT SIDE

F 2

F 1

F 3

F 4

S12

F 6

F 5

F 7

F 8

S13

C1 S1 S2 S3 S6 S7

NCS2

LEFT BEVERAGE VALVES RIGHT BEVERAGE VALVES

NCS3

S11 S10 S15 S14 C4 S16

F 2

F 1

F 3 F 4

C2 / NC2C1

LEFT TOUCHPADS

C4C3 / NC3

RIGHT TOUCHPADS

S11

S12

S10

S13

S14

S15

S16

C = CARB S = SYRUP F = FLAVOR SHOT NC = NON-CARB PW = PLAIN WATER PR = PRESSURE RELIEF

F 5

F 6

F 7

F 8

CO2PR

OUT

TO CARB TANK

FROM CARB TANK

S16 S15 S14 S13 S12 S11 S10

INTERNAL CARB

TANK (OPTIONAL)

S2 S1 PW PRE-

CHILL

S9 S8 S7 S6 S5 S4 S3

PN 020001891

FRP-250 PLUMBING DIAGRAM

= WATER

= SYRUP

= FLAVOR SHOT

2-10

Part Number 020003315 1/11

Section 2 Installation Instructions

Pressure

Relief

Drain Pan SV-250 Shown

Rear of Unit

To Drain

90° Elbow Fitting

Radiator Clamp

Flexible Tubing

Straight Fitting

Radiator Clamp Flexible Tubing

Rear Access for Drain

Hose and Beverage Lines

Drainage Through Bottom Drainage Through Back Rear View

CO2 System

ROUTING INTERNAL CARB TANK PURGE TUBE

Some models are equipped with an internal carbonation tank.These models require that the purg e/pressure relief tubing be routed to a drain.

1. Remove the splash panel.

2. Uncoil tubing and route between the front of the dispenser and the drain pan.

DRAINS

3. Depending on drain location route the tubing through the tubing bundle cutout or out the back of the dispenser.

4. Verify the tubing is not kinked and then secure tubing to maintain a minimum 1" (2.5 cm) air gap at the drain. Follow any applicable local or national codes.

Part Number 020003315 1/11 2-11

Installation Instructions Section 2

Important

Step by Step Installation

GENERAL

Flav’R-Pic and Selectable Ice Series dispense rs have a stainless steel cabinet and lighted merchandiser standard.

Beverage valves, coldplate connections, drain connections and electrical components are front serviceable.

CAPACITIES

Dispenser Valves Ice Storage

FRP-250 16 Flavors, 8

Flavor Shots

SPECIFICATIONS CHART

MIN. MAX

Incoming Plain Water Pressure

Plain Water Pressure to Carb Tank

Ambient Temperature

2 Pressure

(Primary) Electrical 115V/60 Hz/1 230V/50-60 Hz/1 Pre-mix Pressure

Normal 60 psi*

Diet 40 psi* B-I-B (Secondary) 75 psi or according to line run Flavor Shots 30 psi or according to line run

* This is the optimal pressure. For high foam, decrease the pressure,

for spitting/popping, increase the pressure.

40 psi dynamic 70 psi static

55 psi 65 psi

40°F

(4°C)

90 psi 100 psi

UNIT INSTALLATION

1. Place the dispenser in the desired location.

NOTE: The unit must be placed and operated in a horizontal, level position. This unit is not suitable for areas cleaned with a water jet, pressure washers or water hoses.

2. Run the beverage lines and water lines; make sure to install the water connections to the proper inlets. Connection “A” comes from the brass carbonator pump and connection “B” is your plain water supply.

3. Install plumbing drains and insulate.

250 lbs

105°F

(41°C)

7. Purge air from the carbonator tank. Lift the pressure relief valve tab on the carbonator tank until water comes out of the relief valve.

8. Connect the pump deck control lead to the pump motor.

9. Connect power supply cords. (There are (2) two cords that need to be connected to a 115V power supply.)

10. Brix beverage valves.

SYSTEM PRESSURES

1. Incoming tap water - must be at a minimum dynamic pressure of 40 psi and maximum static pressure of 70 psi.

If incoming water pressure is under 40 psi dynamic, a water booster is recommended. If incoming water pressure is over 55 psi, a water regulating valve is recommended.

NOTE: For water booster setups, connect directly to the incoming water to the unit. A regulator may be n eeded to maintain 40 - 55 psi to the carb onator or water may be routed around the booster to the carbonator. If water pressure is too high to the carbonator poor drink carbonation can result.

Water boosters are preset to turn on a t 65 psi and o ff at 85 psi.

2. BIB pressure gauge must be set for 75 psi or according to your line run.

3. Carbonator Pressure gauge (Use Preset Regulator):

- Cold Carbonation set for 75 psi.

- Ambient systems must be set at 90 psi to 105 psi.

NOTE: For models with flavor shots you want to achieve .5 oz (14.787 cc) a second dispense, adjust flow controls accordingly . See Section 3 for ho w to program the flavor shot dispense duration on FRP models.

4. Fill bin with ice.

5. Set flexible manifold for correct drink settings.

6. Turn water supply on to the dispenser.

2-12

Part Number 020003315 1/11

Section 2 Installation Instructions

Brixing

Info

Left Side

Program

Button

Right Side Program Button

Funnel & High Yield Brix Cup

6:1

5.5:1

8.5:1

5:1

WATER

5.5

to 1

8.5

to 1

OZ.

LEFT BOARD RI GHT BOARD

C1 - VA LVE 8 C3 - VALVE 4 C2 - VA LVE 1 1 C4 - VALV E 1 NC2 - VALVE 11 NC3 - VALVE 4 S1 - VALV E 8 S9 - VALVE 15 S2 - VALV E 9 S10 - VALVE 3 S3 - VALV E 9 S11 - VALVE 3 S4 - VALV E 14 S1 2 - VALVE 7 S5 - VALV E 14 S1 3 - VALVE 7 S6 - VALV E 10 S1 4 - VALVE 2 S7 - VALV E 10 S1 5 - VALVE 2 S8 - VALV E 15 S1 6 - VALVE 1 F1 - VALVE 13 F5 - VALVE 6 F2 - VALVE 13 F6 - VALVE 6 F3 - VALVE 12 F7 - VALVE 5 F4 - VALVE 12 F8 - VALVE 5

C = CARB S = SYRUP F = FLAVOR SHOT NC = NON-CARB

DISPENSE TYPE &

VALVE N UMBER

S12

S10

S11

S16 S14

S15

S13

Right Hidden Touchpad Buttons

Left Hidden Touchpad Buttons

FRP-250 WITHOUT FLAVOR SHOTS

Left Carb/ Non-Carb

Right Carb/NonCarb

BRIXING PROCEDURE

If the merchandiser and splash panel are on the front of the unit, remove them. Merchandiser removal will give you access to the syrup and water valves. Splash panel removal will give you access to the plumbing label located on the foam front and/or in the Plumbing section of the Use & Care Manual. This label will be needed to identify valve and touch pad locations.

Placing a control Board into Brix Mode

Control Board Label

NOTE: See Section 3 for Program Mode Operations. Mode 2 puts your Flav'R-Pic into brix mode, follow the

steps below to put a board into brix mode.

1. Choose a control board, if brixing drinks for N1 (Nozzle

1) or N3 use the left control board, if brixing drinks for N3 or N6 use the right control board. Beverage dispense points are designated by a black nozzle.

2. Press the program button and hold for 3 seconds or until the LED displays 1. Press the program button again until 2 is displayed on the control board LED display .

3. Use a high yield brix cup with multiple ratios for the procedure, an example is illustrated below. Use of a funnel between the cup and nozzle will aid in the capture of the syrup during syrup brixing.

Part Number 020003315 1/11 2-13

4. Locate the control board that corresponds with the valve(s) and/or dispense point you want to brix.

NOTE: The buttons for FRP units without flavor shots are located in the same area, but are hidden.

5. Press the program button and hold for 3 seconds or until the LED displays 1. Press the program button again until 2 is displayed on the control board LED display.

NOTE: Programming one board at a time will make it easier for you to identify the corresponding valves and dispense points. See the Programming section in this manual for more detail on all programming modes.

6. With a board in mode 2 you can now brix any water or syrup valve that corresponds to the board. Use the chart on the left to identify the valves and which board they correspond to, see the illustration on the next page for more assistance. Brixing information can also be found on the right hand side of the control board cover label. By using this label in combination with the plumbing label you will be able to identify each valve, water, and/or syrup combination.

Installation Instructions Section 2

Valve 14

Valve 13

Valve 15

Valve 12

Valve 8

C1 S1

Valve 9

S2 S3

Valve 10

S6 S7

Valve 11

C2 NC2

Valve 4

C3 NC3

Valve 3

S11 S10

Valve 2

S15 S14

Valve 1

C4 S16

LEFT SIDE

CONTROL BOARD

Valve Controls - C1, C2, NC2

S1-S8, F1-F4

Valve Controls - C3, C4, NC3

S9-S16, F5-F8

Valve 6

Valve 5

S13

Valve 7

S12

N1 N3

S1, S3, S2, S4

S5, S7, S6, S8,

C2, NC2

S12

S10

S11

S16 S14

S15 S13

N4 N6

S9, S11,

S10, S12,

C3, NC3

S13, S15, S14, S16,

F1, F3, F2, F4

F5, F7, F6, F8

RIGHT SIDE

CONTROL BOARD

= WATER = SYRUP = FLAVOR SHOT

Valve 14

Valve 13

Valve 15

Valve 12

Valve 8

C1 S1

Valve 9

S2 S3

Valve 10

S6 S7

Valve 11

C2 NC2

Valve 4

C3 NC3

Valve 3

S11 S10

Valve 2

S15 S14

Valve 1

C4 S16

LEFT SIDE

CONTROL BOARD

Valve Controls - C1, C2, NC2

S1-S8, F1-F4

Valve Controls - C3, C4, NC3

S9-S16, F5-F8

Valve 6

Valve 5

S13

Valve 7

S12

RIGHT SIDE

CONTROL BOARD

S1, S3, S2, S4

S5, S7, S6, S8,

C2, NC2

S9, S11,

S10, S12,

C3, NC3

S13, S15, S14, S16,

F1, F3,

F2, F4

F5, F7, F6, F8

F 1

F 2

F 3

F 5

F 6

F 8

F 7

S6S7S8

S12

S11

S10

S16

S15

S14

S13

Right Hidden Touchpad Buttons

Left Hidden Touchpad Buttons

FRP-250 WITHOUT FLAVOR SHOTS

Left Carb/ Non-Carb

Right Carb/NonCarb

S9 (Syrup 9) on Valve 15 is the only syrup that does not correspond to the side it is mounted to, both visually and functionally all other valves,

touch pads, and dispense points correspond with the board on the

same side to which they are attached.

GENERAL BRIXING PROCESS

1. With the corresponding control board set to brix mode and displaying a 2 you may brix a beverage nozzle (N1, N3, N4, or N6). When brixing the syrup use of a funnel between the cup and nozzle will aid in the capture of the syrup. (See nozzle order below)

2-14

Nozzles from left to right: N1, N2, N3, N4, N5, N6.

2. To brix carbonated or non-carbonated water for a dispense point leave the nozzle in place and hold the brix cup with the water side of the cup under the nozzle area. Non-Carbonated water is only available at N3 (Nozzle 3) and N4.

3. By referencing the control box label and plumbing diagram press the flavor shot touch pad that corresponds with the water you wish to brix. If brixing the left side it will be one of the following; F1 (Flavor Shot 1), F2, or F3. When brixing the right side F5, F6, or F7 will be used. On non-flavor shot units the touch pads are located in the same area except they are hidden.

S12

S11

S10

S16 S14

S15

4. The correct volume should be 7 oz. during the fixed dispense in mode 2. If adjustment is needed to attain this volume, make adjustments corresponding valve as needed until volume is satisfactory.

NOTE: The touch pad mount can be tilted forward in order to give you better access to the valves.

5. For syrup brixing insert the funnel in the section of the brix cup that corresponds with the syrup you are brixing (refer to the brix cup label for correct High Yield Syrup Ratios). Place the cup/funne l under the nozzle area and press any brand touch pad a rea associated with that nozzle dispense point. For example S1 (Syrup 1), S2, S3, and S4 touch pad areas will be used to brix N1 (Nozzle 1).

6. Syrup will dispense for a fixed duration and should be even with the 7 oz. water mark on the cup

7. Check each syrup position and adjust syrup on the corresponding valve as necessary. A plumbing label is located on the foam front of the unit showing the position of each valve and syrup port. See the Plumbing Diagram page.

8. When finished, move on to another nozzle or if brixing is complete, return the control board to the dispense mode by pressing the program button and holding for 3 seconds or until the LED displays 0.

9. Replace the splash panel and merchandiser.

Part Number 020003315 1/11

S13

Section 2 Installation Instructions

NOZZLE 1 (N1) WATER AND SYRUP BRIXING

1. With the left control board set to brix mode and displaying a 2 you can now brix the carbonated water for N1 (Nozzle 1) located at the far left hand side of the unit.

2. To brix the carbonated water for this dispense point leave the nozzle in place, hold the brix cup with the water side of the cup under N1 (Nozzle 1), and press the F1 (Flavor Shot 1) button. Water will dispense for a fixed duration.

3. The correct volume should be 7oz. (207.01 cc). If adjustment is needed to attain this volume, make adjustments to the left side of valve 8 (C1) adjustment screw as needed until flow rate is satisfactory.

4. For syrup brixing place the brix cup with the syrup side of the cup under the N1 and press the touch pad area for S1 (Syrup 1), S2, S3, or S4, and the corresponding syrup will dispense for a fixed duration (Refer to the brix cup label for correct High Yield Syrup Ratios).

5. Syrup should be even with the 7oz . ( 20 7. 01 cc) water mark on the cup.

6. Check each syrup position and ad ju st syrup on th e corresponding valve as necessary . A plumbing label is located on the foam front of the unit showing the position of each valve and syrup port. See the Plumbing Diagram page.

7. Move to another nozzle or if you are finished brixing return the control board to the dispense mode by pressing the program button and holding for 3 seconds or until the LED displays 0. Replace the splash panel and merchandiser.

NOZZLE 2 (N2) WATER AND SYRUP BRIXING

This is a flavor shot dispense point, designated so by it's blue nozzle, no brixing is needed. Either a 1 or 2 second dispense duration can be selected in program mode 1 from the left side control board. (See the Programming section for more information.)

NOZZLE 3 (N3) CARB/NON-CARB WA TER & SYRUP BRIXING

1. With the left control board set to brix mode and displaying a 2 you can now brix carbonated or noncarbonated water for N3 (Nozzle 3). (See Programming Mode 1 to designate carb/non-carb)

2. To brix th e car b on at ed wa ter for this dispense point leave the nozzle in place, hold the brix cup with the water side of the cup under N3 (Nozzle 3), and press the F2 (Flavor Shot 2) button. Carbonated water will dispense for a fixed duration.

3. To brix the non-carbonated water for this dispense point leave the nozzle in place, hold the brix cup with

the water side of the cup under N3 (Nozzle 3), and press the F3 (Flavor Shot 3) button. Water will dispense for a fixed duration.

4. The correct carb and non-carb volume should be 7oz. (207.01 cc). If adjustment is needed to attain this volume, make adjustments to the left side of valve 11 (C2) adjustment screw for carbonated water and the right side of valve 11 (NC2) adjustment screw for non-carbonated water as needed until flow rate is satisfactory.

5. For syrup brixing place the brix cup with the syrup side of the cup under the N3 (Nozzle 3) and press the touch pad area for S5 (Syrup 5), S6, S7, or S8 and the corresponding syrup will dispense for a fixed duration (Refer to the brix cup label for correct High Yield Syrup Ratios).

6. Syrup should be even with the 7oz. (207.01 cc) water mark on the cup.

8. Move to another nozzle or if you are finished brixing return the control board to the dispense mode by pressing the program button and holding for 3 seconds or until the LED displays 0. Replace the splash panel and merchandiser.

NOZZLE 4 (N4) CARB/NON-CARB WA TER & SYRUP BRIXING

1. With the right control board set to brix mode and displaying a 2 you can now brix carbonated or noncarbonated water for Nozzle 4 (N4). (See Programming Mode 1 to designate carb/non-carb)

2. To brix the carbonated water for this dispense point leave the nozzle in place, hold the brix cup with the water side of the cup under N4 (Nozzle 4), and press the F6 (Flavor Shot 6) button. Water will dispense for a fixed duration.

3. T o b rix the non-carbonated water fo r this dispense point leave the nozzle in place, hold the brix cup with the water side of the cup under N4 (Nozzle 4), and press the F7 (Flavor Shot 7) button. Water will dispense for a fixed duration.

4. The correct carb and non-carb volume should be 7oz. (207.01 cc). If adjustment is needed to attain this volume, make adjustments to the left side of valve 11 (C3) adjustment screw for carbonated water and the right side of valve 4 (NC3) adjustment screw for non-carbonated water as needed until flow rate is satisfactory .

Part Number 020003315 1/11 2-15

Installation Instructions Section 2

Important

5. For syrup brixing place the brix cup with the syrup side of the cup under the N4 (Nozzle 4) and press the touch pad area for S9 (Syrup 9), S10, S11, or S12 and the corresponding syrup will dispense for a fixed duration (Refer to the brix cup label for correct High Yield Syrup Ratios).

6. Syrup should be even with the 7oz. (207.01 cc) water mark on the cup.

7. Check each syrup position and adjust syrup on the corresponding valve as necessary . A plumbing label is located on the foam front of the unit showing the position of each valve and syrup port. See the Plumbing Diagram page.

8. Move to another nozzle or if you are finished brixing return the control board to the disp ense mode by pressing the program button and holding for 3 seconds or until the LED displays 0.Replace the splash panel and merchandiser .

NOZZLE 5 (N5) WATER AND SYRUP BRIXING

This is a flavor shot dispense point, designated so by it's blue nozzle, no brixing is needed. Either a 1 or 2 second dispense duration can be selected in program mode 1 from the right side control board. (See the Programming section for more information.)

NOZZLE 6 (N6) WATER AND SYRUP BRIXING

1. With the right control board set to brix mode and displaying a 2 you can now brix the carbonated water for N6 (Nozzle 1) located at the far right hand side of the unit).

2. To brix the carbonated water for this dispense point leave the nozzle in place, hold the brix cup with the water side of the cup under N6 (Nozzle 6), and press the F5 (Flavor Shot 5) button. Water will dispense for a fixed duration.

3. The correct volume should be 7oz. (207.01 cc). If adjustment is needed to attain this volume, make adjustments to the left side of valve 1 (C4) adjustment screw as needed until flow rate is satisfactory.

4. For syrup brixing place the brix cup with the syrup side of the cup under the N6 (Nozzle 6) and press the touch pad area for S13 (Syrup 13), S14, S15, or S16, and the corresponding syrup will dispense for a fixed duration (Refer to the brix cup label for correct High Yield Syrup Ratios).

5. Syrup should be even with the 7oz. (207.01 cc) water mark on the cup.

6. Check each syrup position and adjust syrup on the corresponding valve as necessary. A plumbing label is located on the foam front of the unit showing the position of each valve and syrup port. See the Plumbing Diagram page.

Starting Your Beverage System & Dispenser

Upon completion of the beverage dispenser and / or system installation, all tubing, dispenser, and system components must be cleaned and sanitized prior to use.

NOTE: At installation, equipment, dispensers, and tubing get moved through many environments, dirt, dust, chases, insulation, drywall, etc. It is an important procedure and best practice to address cleaning to deliver the best quality drink to your customer.

Clean and sanitize the water and syrup circuits according to instructions provided in this manual. Clean and sanitize the dispenser components according to instructions provided in this manual. Seal to counter top when no legs are used with the unit. Consult and use local health codes if a discrepancy occurs between this manual and your local health codes.

2-16

Part Number 020003315 1/11

Section 3 Operation

1800

Dispenser

Counter top

Carbonator Tank

Carbonate,

Non-carbonate

Beverage Manifold

Tap Water

Syrup

Bag-in-box Syrup Carton

Syrup

Bag-in-box Syrup Carton

CO2

BIB Syrup Pump

CO2

CO2 Cylinder

Primary Regulator

BIB Syrup Pump

Section 3

Operation

General System Overview

Typical Flav’R-Pic Series Internal Carbonation Beverage Dispensing System

Part Number 020003315 1/11 3-1

Operation Section 3

Merchandiser

Nozzles

Key Switch

Drainpan Grid

Drainpan

Splash Panel

Lower Merchandiser

& Beverage Selection

Touch Pads

Nozzles

Selectable Ice

Touch Pad

Ice Chute

ADA Touch Pads

(on units with this feature)

ADA Touch Pads

(on units with this feature)

Half Dice

3/8" x 1-1/8" x 7/8"

(1.0 x 2.9 x 2.2 cm)

Half Dice

3/8" x 1-1/8" x 7/8"

(1.0 x 2.9 x 2.2 cm)

Sequence of Operation

ICE RECOMMENDED FOR DISPENSING

Dispensers are designed to dispense hard, cube ice up to one-inch square. The ice shapes and sizes listed above are recommended for dispensing. Warm “Super Cooled” Ice Before Dispensing: “Super Cooled” ice is not recommended for dispensing. “Super cooled” ice is ice that has been stored in freezers below 32°F. Should it be necessary to temporarily use “super cooled” ice, allow the ice to warm at room temperature for 25 to 30 minutes before placing the ice in the dispenser.

Flake or “nugget” ice is NOT to be dispensed from the Flav'R-Pic. The Flav'R-Pic comes equipped with the selectable ice feature so you are able to choose between cubed or crushed ice making the addition of a flake/nugget icemaker unnecessary.

3-2

Component Identification

ICE STORAGE AND DISPENSING

As the customer presses the rocking chute, the arm at the top left rear of the chute pushes upward on the door lock. The door opens until it contacts the stops in the mounting brackets. The plastic arm on the ice chute also activates the lever of the ice dispensing switch. When activated, the micro switch starts the gear motor. The gear motor turns the paddle wheel and agitator ar m.

The paddlewheel carries ice. Periodic agitation is standard on the 30" and larger dispensers. During periodic agitation, the paddle wheel and agitator turn for approximately three seconds every three and one halfhours. The door lock prevents ice from being dispensed during the agitation cycle.

BEVERAGE VALVES

Post-mix beverage valves are designed to precisely meter the flow of both water and syrup to obtain the proper mixing ratio. The syrup and soda water components of the post-mix beverage are mixed as they leave the beverage valve.

Part Number 020003315 1/11

Section 3 Operation

From Water Supply

T o Noncarbonated W ater Inlet Barb

Water to Carbonator Pump

Filter

Water Regulator 40–70 PSI

Booster System (If Required)

To CO

Manifold (BIB

Pumps) from

Supply

70 PSI

T o Syrup Inlet Barbs on Unit

T o BIB Pumps

from BIB

To BIB

Pump

BIB

ROCKING CHUTE ICE DISPENSING

On units without the selectable ice option, as the customer presses the rocking chute, the arm at the top left rear of the chute pushes upward on the door lock. The door opens until it contacts the sto ps in the mounting brackets. The plastic arm on the ice ch ute also activates the lever of the ice dispensing switch. When activated, the micro switch starts the gear motor. The gear motor turns the paddle wheel and agitator bar.

SELECTABLE ICE SEQUENCE OF OPERATION

On units equipped with the selectable ice option, as a customer presses the ice chute or pushes the sanitary lever towards the unit with their cup, with “Crushed Ice” selected on the ice selection pad, the rocking chute door lif ts an d actuates micro switch which initiates the crushed ice dispensing process. The micro switch is activated when the lever is approximately 1/4 inch from reaching the splash panel of the unit. When activated, the micro switch starts the gear motor and ice crusher motor . The gear motor turns the paddle wheel and U-bar agitator. The paddle wheel carries ice to the crusher assembly . Once the ice reaches the crusher housing, four stationary blades and three rot ating blades crush the ice and push it through the opening in the ice crusher housing. The crushed ice then falls through the opening into the ice chute, and into the customer’s cup. If the merchandiser is removed no power is available to the crusher or gear motor and no ice can be crushed and/or dispensed.

CARBONATION

The purpose of the carbonator is to take regular tap water at street water pressure (minimum 20 PSI, maximum 80 PSI, dynamic or flowing pressure) 1/2" water line and increase the water to beverage system pressure (usually 100 PSI). This water is then combined with the CO same pressure, the CO

gas. Because the water and gas are at the

will dissolve into the water.

Chilling the mixture before dispensing will assist in locking the carbon dioxide into the water. After dispensing, the CO The CO

will gradually leave the liquid due to pressure

may be unlocked from the liquid.

and temperature changes.

Components

The components of the carbonator are: water pump, an electric motor to operate the pump, carbonator tank where the water and CO

Part Number 020003315 1/11 3-3

mix, and a water level control.

Operation

Carbon Dioxide (CO

) leaves the storage tank and

arrives at the carbonator tank through the gas inlet. Water supply enters the carbonator pump inlet at regular street water line pressure (minimum 20 PSI, maximum 80 PSI, dynamic or flowing pressure). The water pump increases the pressure of the water, which allows the water to flow into the carbonator tank. The CO

and the

water mix together in the carbonator to produce the carbonated water that is then sent to the soda dispenser.

The agitation of the water and CO

together in the tank

under high pressure creates the soda water. The quality of carbonation (percent of CO

mixed in the water)

increases as the water temperature decreases and exposure time increases.

The water level in the carbonator tank is controlled by a water level control in the tank. This control turns the pump motor off and on to maintain a preset level of liqu id in the tank. The water level control may be electronic probes or a mechanical float.

SYRUP DELIVERY SYSTEM

Your syrup location can vary depending on the volume of beverages served and ease of accessibility. Your beverage system may set in a back storage room or under the counter of the dispenser. Configurations are almost limitless. Check the temperatures expected for the storage location. Adverse temperatures can affect the storage and quality of beverage products. It is recommended the temperature of storage location should not fall below 40°F (4°C) or rise above 90°F (32°C).

BACK ROOM PACKAGE

Operation Section 3

RED

COM NC

1. Incoming tap water - should be at a minimum dynamic pressure of 40 psi and maximum static pressure of 70 psi.

2. Carbonator Water pump motor - Powers the water pump. The water pump motor is part of the carbonator pump deck.

3. Carbonator Water pump - Pumps ta p water into the carbonator tank. The water pump is part of the carbonator . The incoming water for the carbonator must be first run through the pump before connecting to the proper cold plate inlet.

4. Internal/External Carbonator tank - Combines CO

gas and tap water to form carbonated water.

The “carbonator” is the carbonator tank, water pump and water pump motor.

5. CO

cylinder - Holds highly pressurized carbon

dioxide (CO aluminum cylinder tank. CO

). The CO2 cylinder is a steel or

gas flows through the

primary pressure regulator.

6. BIB pressure gauge - Set for 75 psi. Indicates CO pressure going to B-I-B pumps.

7. Primary pressure regulator - Lowers the CO pressure, to 100 psi, so the CO

gas will be at the

gas

proper pressure to enter the carbonator regulator.

8. Lowered outgoing pressure - Set for 75 psi. Gauge indicates lowered outgoing pressure from the CO

cylinder after being routed through the primary

pressure regulator at 100 psi.

9. Secondary pressure regulator - Lowers the CO gas pressure before the CO pump. CO

pressure activates the syrup pump.

gas flows to the syrup

10. Syrup pump - Draws syrup out of the bag-in-box syrup package. Syrup flows through the syrup lines to the dispenser for chilling, then dispensing. There is a syrup pump for each bag-in-box syrup system.

B-I-B

The Bag-In-Box system refers to a plastic disposable bag. The B-I-B normally contains 5 gallons of syrup, however some locations offer 2-1/2 gallon B-I-B unit s. This plastic bag is then held inside a cardboard or other container. B-I-B systems are for post-mix applications only .

PUMPS

The syrup in a B-I-B system is delivered to the beverage system through gas operated pumps. These pump s extract the syrup out of the bags, forcing the syrup throughout the system.

AUTO BAG SELECTORS

These are used on higher volume B-I-B systems where two or more bags of the same product are connected to one pump and one system. An auto bag selector is essentially a valve that automatically changes from one bag (or series of bags) to another bag (or series of bags) of syrup as the bags empty , allowing a consta nt flow of product.

FRP-250 NON-ADJUSTABLE AGITATION TIMER

On units without selectable ice option, the timer is nonadjustable and is set to agitate the ice for 3 seconds every

3.5 hours. Activating the dispenser will reset the timer. After

3.5 hours of non-use, the timer will energize the dispenser motor .

The LED tells the technician in which mode the timer is operating. Rather than a jumper pin, this timer has a female spade connector that must be connected to terminal number 6.

When this jumper is in place, the LED will blink at one second intervals, this is the run mode.

When the jumper is open, the LED will flash every

0.4 second. This is the test mode and the timer will cycle every 55 seconds in test mode. If the timer is left in test mode, it will automatically reset to run mode.

11. Bag-In-Box syrup car tons - Box which contains a plastic bag, filled with syrup.

RACKING

Regardless if you are working on a B-I-B or Figal system, a place will be designated for placement of the product. A rack (or shelf) system affords systematic placement and complete usage of the beverage p aid for. The B-I-B rack allows the boxes to lay properly for syrup dispersal. Please check with your B-I-B syrup supplier. Some boxes must be slightly tilted down, while others may be in virtually any position. The Figal tank rack keeps the newer and full tanks organized at one end of the beverage line with the partial tanks at the other.

3-4

FRP-250SCI NON-ADJUSTABLE AGITATION

On units equipped with the selectable ice option, timed agitaion for Flav’R-Pic units is handled by the control board and is not adjustable.

NOTE: This timer is re-settable, timed agitation every

3.5 hours from last dispense or when the power supply is broken.

Part Number 020003315 1/11

Section 3 Operation

Brixing

Info

Mode 1 Carb/

non-Carb & Flavor Shot

Durations

Right Side Program Button

Left Side Program Button

Door

Door Lock

Door

Ice

Delivery

Door Stops

Door

Door Lock

1/16”

1/4”

Tab

Switch Arm

CONTROL BOX LABEL

The control box label is your programming reference sheet and control board identifier . Becoming familiar with this label will greatly assist you in programming, brixing and even trouble shooting the boards on the Flav'R-Pic unit if necessary. The illustration above tells you what each area of the label does. In each called out area there are abbreviated instructions for one of the three programming modes.

MODE 1 = carb/non-carb & Flavor shot INFO MODE 2 = Brixing MODE 3 = Touch pad LED Sequencing a program button is located just to the right of each

numbered LED display. The one on the left controls the left control board and the one on the right controls the right control board. Holding either in for approximately 3 seconds will put the respective board into a programming mode. (See the Programming section for programming mode details.) For this label to make sense, especially when brixing, you will need to reference the plumbing label located on the foam front behind the splash panel and/or in the plumbing section of this manual. It is recommended to only program one board at a time.

Operation Checks and Adjustments

FRP-250 (NON-ICE CRUSHING UNIT) ICE DELIVERY SWITCH ADJUSTMENT

To properly adjust the switch, first unplug the power cord to the unit then remove the merchandiser. This will give you access to the ice delivery switch located on the left side of the rocking chute.

Begin by observing the chute by slowly pushing against the rocking chute. When the ice delivery switch clicks, measure the distance from the door stop s on the rocking chute bracket to the door. The distance between the two must be no more than 1/4” (0.64 cm), but no less than 1/16” (0.16 cm).

Also located around the top and bottom edges on the control box label are the locations of the wire harnesses that are connected to the boards behind the box and th e valve or touch pad connection they plug into.

Part Number 020003315 1/11 3-5

The left side of the rocking chute has a tab that pushes up on the ice delivery switch. To adjust it, use needle nose pliers and bend the arm of the switch up or down in order to change the point where the tab makes contact with the switch arm.

Operation Section 3

S12

S10

S11

S16 S14

S15

S13

Right Flavor Shots

Left Flavor Shots

FRP-250 WITH FLAVOR SHOTS

Left Carb/ Non-Carb

Right Carb/NonCarb

Right Hidden Touchpad Buttons

Left Hidden Touchpad Buttons

FRP-250 WITHOUT FLAVOR SHOTS

Left Carb/ Non-Carb

Right Carb/NonCarb

Important

EXTERNAL BRIX MODE

How to Check FRP Brix Externally

If your FRP-250 has a control board with the external brix check ability you will be able to put the unit into brix mode by doing the following:

1. Turn the key switch to the “OFF” position.

2. With the key switch still in the “OFF” position, press and hold the F1 touch pad button for the left side or F5 for the right while turning the key switch back to the “ON” position.

• F1 = Left Side Brix Check

• F5 = Right Side Brix Check

4. In this mode you can now check the brix for any water or syrup valve that corresponds to the board. Use the illustration in Installation/Brixing or the Control board, V alve, Touch Pad Matrix to identify the valves and which board they correspond to. Brixing information can also be found on the unit, on the right hand side o f the control board cover label. By using this label in combination with the plumbing label located on the foam front you will be able to identify each valve, water , and/or syrup combination.

5. When finished checking the brix return the unit to dispense mode by turning the keyswitch to the "OFF" position, waiting till the touch pad LEDs are not illuminated, then turn the keyswitch back to the "ON" position.

If left in external brix mode for longer than 5 minutes it will automatically time out and return to dispense mode.

If brix adjustments are needed you will have to remove the merchandiser to make the mechanical adjustments. Plea se see PROGRAM MODE 2 in this section for internal brixing instructions using the control board and the SECTION 2 / Brixing Procedure for detailed instructions on brixing the FRP-250.

S12

S11

S10

S16 S14

S15

S13

NOTE: The buttons for FRP units without flavor shots are located in the same area, but are hidden.

3. You can now stop pressing on the F1 or F5 button and the 4 LEDs around the touch pad area should now be illuminated. If not illuminated you did not successfully go into external brix mode and need to try again, or the FRP unit is not equipped with this program mode.

In this setting when a corresponding touch pad is pressed water or syrup will be dispensed for a fixed duration in order to check your ratios using a brix cup.

CRUSHED OR CUBED DEFAULT

This selectable ice option will allow the unit to always default to either cube or crushed ice or remain at the last selection. This only applies to control boards 020000875 Rev 7 and up.

How to set default ice dispense setting CUBE DEFAULT

1. Power on the unit by plugging in receptacle and holdi ng the cube button at the same time, cube will flash 2 times. Unit will now change to cube 10 seconds after crush is selected and/or used.

CRUSH DEFAULT

2. Power on the unit by plugging in receptacle and holdi ng the crushed button at the same time, crush will flash 2 times. Unit will now change to crush 10 seconds after cube is selected and/or used.

LAST SELECTION DEFAULT

3. Power on the unit by plugging in receptacle and holding cube and crush at the same time, cube and crush will flash 2 times. Unit will now remain in selection of last request.

NOTE: If power is lost to the unit and then powered up again the unit will retain the last setting and not return to factory settings.

3-6

Part Number 020003315 1/11

Section 3 Operation

Brixing

Info

Mode 1 Carb/

non-Carb & Flavor Shot

Durations

Right Side Program Button

Left Side Program Button

S12

S10

S11

S16 S14

S15

S13

Right Flavor Shots

Left Flavor Shots

FRP-250 WITH FLAVOR SHOTS

Left Carb/ Non-Carb

Right Carb/NonCarb

Right Hidden Touchpad Buttons

Left Hidden Touchpad Buttons

FRP-250 WITHOUT FLAVOR SHOTS

Left Carb/ Non-Carb

Right Carb/NonCarb

PROGRAM MODE 1 Carb/Non-Carb & Flavor Shot Duration Settings

Mode 1 displayed above, allows you to select your carb/ non-carb settings for dispense points N3 (Nozzle 3) through the left control board and/or N4 (Nozzle 4) with the right control board. Only nozzles N3 and N4 have the option to be a non-carb drink, N1 and N6 are carbonated only. Mode 1 is also used to set a 1 or 2 second dispense duration for flavor shots on N2 and N5 using their corresponding control board.

N3 & N4 Carbonated or Non-Carbonated Drinks

3. To set a carbonated drink for N3 (Nozzle 3) touch one of the following touch pads; S5, S6, S7, or S8 until the LEDs around the touch pad are constant.

4. To set a non-carbonated drink for N3 (Nozzle 3) touch one of the following touch pads; S5, S6, S7, or S8 until the LEDs around the touch pad are blinkin g.

•Constant LEDs = Carbonated

•Blinking LEDs = Non-Carbonated

5. Follow the same instructions for N4 (Nozzle 4) using the right control board and touch pads S9, S10, S11, or S12.

6. When you are finished press the program button to go to a different mode or save your settings and return the control board to the dispense mode by pressing the program button and hold ing for 3 seconds or until the LED displays 0.

Flavor Shot Dispense Duration

1. Choose a control board, if programing flavor shots for N2 (Nozzle 2) use the left control board, if programming shots for N5 use the right control board. Flavor shot dispense points are designated by a blue nozzle.

S12

S11

S10

S16 S14

S15

S13

1. Choose a control board, if programing N3 (Nozzle 3) use the left control board, if programming N4 use the right control board. Beverage dispense points are designated by a black nozzle.

2. Press the program button and hold for 3 seconds or until the LED displays 1.

3. To set a 1 second shot for N2 (Nozzle 2) touch one of the following touch pads; F1, F2, F3, or F4 until the LEDs around the touch pad are constant.

4. To set a 2 second shot for N2 (Nozzle 2) touch one of the following touch pads; F1, F2, F3, or F4 until the LEDs around the touch pad are blinking.

•Constant LEDs = 1 second shot

•Blinking LEDs = 2 second shot

5. Follow the same instructions for N5 (Nozzle 5) using the right control board and touch pads F5, F6, F7, or F8.

Part Number 020003315 1/11 3-7

Operation Section 3

Important

PROGRAM MODE 2

Brixing

Mode 2 displayed above, puts your Flav'R-Pic into brix mode. In this setting when a corresponding touch pad is pressed water or syrup will be dispensed for a fixed duration in order to set your ratios using a standard brix cup and making adjustments to the mechanical valves. Follow the steps below to put a board into brix mode.

1. Choose a control board, if brixing drinks for N1 (Nozzle

1) or N3 use the left control board, if brixing drinks for N3 or N6 use the right control board. Beverage dispense points are designated by a black nozzle.

2. Press the program button and hold for 3 seconds or until the LED displays 1. Press the program button again until 2 is displayed on the control board LED display .

NOTE: Programming one board at a time will make it easier for you to identify the correspondin g valves and d ispense points.

3. With the a board in mode 2 you can now brix any water or syrup valve that corresponds to the board. Use the illustration in Installation/Brixing or the Control board, V alve, Touch Pad Matrix to identify the valves and which board they correspond to. Brixing information can also be found on the unit, on the right hand side of the control board cover label. By using this label in combination with the plumbing label located on the foam front you will be able to identify each valve, water, and/or syrup combination.

4. Replace the nozzle when done then move on to another nozzle or if you are finished brixing return the control board to the dispense mode by pressing the program button and holding for 3 seconds or until the LED displays 0.

A brixing break down for each nozzle is available in the Installation/Brixing section of this manual.

PROGRAM MODE 3

Light Sequences

3. With the left control board in mode 3 you can now choose one of the touch pad LED lighting sequences by pressing one of the following touch pad areas;

S1 = Flash outside to center S2 = Flash center to outside S3 = Flash all S4 = Continuously on all S5 = Chaser left to right S6 = Chaser right to left S7 = Off all S8 = Flash outside to center, Flavor Shot Off

NOTE: It is recommended that both boards be set to the same lighting sequence. If not the boards will not be able to sync and lighting behavior may become erratic.

4. With the right control board in mode 3 you can now choose one of the touch pad LED lighting sequences by pressing one of the following touch pad areas;

S16 = Flash outside to center S15 = Flash center to outside S14 = Flash all S13 = Continuously on all S12 = Chaser left to right S11 = Chaser right to left S10 = Off all S9 = Flash outside to center, Flavor Shot Off

When installed on a FRP without flavor shots the lighting sequence S8 & S9 should be used. All other units are set to S1 & S16 by default.

5. When done move on to another programming mode or if you are finished return the control board to the dispense mode by pressing the program button and holding for 3 seconds or until the LED displays 0.

CONTROL BOARD TIME OUT

Mode 3 displayed above, allows you to set the light sequence for the touch pad LEDs. Follow the steps below to place the board into this mode and set sequences.

1. Choose a control board, if setting the light sequence for the touch pad area on the left use the lef t control board, if you are setting them for the right, use the right control board.

2. Press the program button and hold for 3 seconds or until the LED displays 1. Press the program button again until 3 is displayed on the control board LED display .

3-8

If a control board is left in any program mode for longer than 5 minutes it will automatically time out and return to dispense mode 0. In order to enter back into a program mode you will need to press the program button and hold for 3 seconds or until the LED displays 1 again.

Part Number 020003315 1/11

Section 3 Operation

NOZZLES FRP-250 & FRP-250SCI Tubing Layout

Part Number 020003315 1/11 3-9

Operation Section 3

System power on

(24V from transformer)

Energize

Touchpad (active)

Touchpad LEDs (sync w/other touchpad)

LCD Display

= 2

LCD Display

= 1

Brand or Flavor?

Flavor

Brand

Carb/Non-Carb Mode (Brand only)

Cont. LED - carbonated Flash LED (0.5s on/off) - plain

Tap touchpad to switch

Dispense Time Mode (Flavor only)

Cont. LED - 1s dispense Flash LED (0.5s on/off) - 2s dispense

Tap touchpad to switch

LCD Display

= 0

Brix Mode

Fixed 1.6s dispense

Brand = syrup and Flavor = F1 = C1, F2 = C2, F3 = NC2 F5 = C4, F6 = C3, F7 = NC3

Tap touchpad to activate

Normal Dispense Mode

Brand - ON MODE - Water on then Syrup on 60 ms later.

OFF MODE - Syrup off then Water off 60 ms later.

Flavor shot - 1s or 2s (release and press - no delay between dispenses)

LED Sequence Mode

Touch brand button location shown below to change

1. LED flash outside to center (0.5s on/off) Default (S1 and S16)

2. LED flash center to outside (0.5s on/off) (S2 and S15) )41S dna 3S()ffo/no s5.0( lla hsalf DEL .3 )31S dna 4S(suounitnoc DEL .4 )11S d

na 5

S(t

hgir ot tfel

resahc DEL .5

)21S dna 6S(tfel ot thgir resahc DEL .6 )01S dna 7S(lla ffo DEL .7

LCD Display

= 3

Program Mode?

Prog button

pressed > 3s?

Prog button

pressed > 3s or

300s elapsed?

Prog button

pressed > 3s or

300s elapsed?

Prog button

pressed > 3s or

300s elapsed?

Control Logic Matrix

3-10

Part Number 020003315 1/11

Section 3 Operation

Valve 14

Valve 13

Valve 15

Valve 12

Valve 8

C1 S1

Valve 9

S2 S3

Valve 10

S6 S7

Valve 11

C2 NC2

Valve 4

C3 NC3

Valve 3

S11 S10

Valve 2

S15 S14

Valve 1

C4 S16

PCB Dispense

Valve Controls - C1, C2, NC2

S1-S8, F1-F4

PCB Dispense

Valve Controls - C3, C4, NC3

S9-S16, F5-F8

Valve 6

Valve 5

S13

Valve 7

S12

PCB Crusher

OPTIONAL

Transformer

S2 S4

S6 S8

N1 N3

S1, S3,

S2, S4

S5, S7, S6, S8,

C2, NC2

S12 S1 0

S11 S9

S16 S14

S15 S13

S9, S11,

S10, S12,

C3, NC3

S13, S15, S14, S16,

S8S7S6S

S4S3S2S

EXTERNAL

CONNECTIONS

F1, F3,

F2, F4

F5, F7,

F6, F8

24VAC

115VAC

(

)

Control board, Valve, Touch pad Matrix

Part Number 020003315 1/11 3-11

Operation Section 3

ADA Touch

Pads

ADA T ouch Pads

CORRESPONDING PAD

ADA 1

ADA 2

CORRESPONDING PAD

S12

S10

S11

S16 S14

S15

S13

S12

S10

S11

S16 S14

S15 S13

ADA 3

ADA 4

ADA TOUCH PADS

ADA touch pads on units with this option are located on both the right & left hand sides of the splash panel for handicapped accessibility to drink flavors.

ADA TO UCH PAD MATRIX

The ADA touch pads are configured to mimic the function of the main touch pads on the left and right sides of the unit located above the dispense nozzles.

ADA 1 = Nozzle 1 (N1) ADA 2 = Nozzle 3 (N3) ADA 3 = Nozzle 4 (N4) ADA 4 = Nozzle 6 (N6)

See Illustration Above.

3-12

Part Number 020003315 1/11

Section 4 Maintenance

Caution

Warning

Section 4

Maintenance

Cleaning

DAILY CLEANING

All cleaning must meet your local health department regulations. The following cleaning instructions are provided as a guide.

Use only warm soapy water to clean the exterior of the tower. Do not use solvents or other cleaning agents. Do not pour hot coffee into the drain pan. Pouring hot coffee down the drain pan can eventually crack the drain pan, especially if the drain pan is cold or still contains ice.

Electric Shock Hazard

Unplug unit before servicing or cleaning.

When using cleaning fluids or chemicals, rubber gloves and eye protection should be worn .

Clean the merchandiser, lower merchandiser, touch pads, splash panel, nozzles and exterior of unit:

1. Turn off the key switch located on either right or left side of the unit.

2. Lift the grid and remove it from the drain pan.

3. Using mild soap, warm water and a clean cloth, wipe the drain pan and splash panel. Then, rinse with clean, warm water. Allow plenty of warm (not hot) water to run down the drain of the drain pan, to remove syrup residue that can clog the drain opening.

4. Wash the grid, then rinse with clean water . Place the grid back in the drain pan.

5. Wash all exterior surfaces of the unit with warm water and a clean cloth. Wipe again with a clean, dry cloth.

Clean the dispensing nozzles:

6. Remove nozzles from each dispense point by (a) grasping it firmly & turning it clockwise about 1/4" then (b) pulling down.

Part Number 020003315 1/11 4-1

7. Rinse nozzle with warm, clean water.

8. Clean nozzles with soapy water and a soft bristle brush.

9. Clean the underside of the nozzle area below the lower merchandiser with warm, soapy water. Rinse with clean damp towel then wipe again with a clean, dry cloth.

10. Replace nozzles by following step 6 in reverse (b, a).

11. Turn on the key switch.

Maintenance Section 4

Caution

Warning

MONTHLY CLEANING

6. Prepare 2 gallons of sanitizing solution by mixing 1/2 ounce of household bleach (that contains 5.25 %

Unplug unit before servicing or cleaning ice bin. Ice bin contains part s tha t can move at any time and

will cause injury if hands are in the way.

When using cleaning fluids or chemicals, rubber gloves and eye protection must be worn .

Clean and sanitize the ice bin:

1. Unplug unit and remove all ice from the ice bin.

2. Mix a solution of mild detergent to clean the dispenser bin and components.

3. Wash the ice bin using a sponge and the mild detergent solution.

4. Using the mild detergent solution and a soft bristle brush or clean cloth, clean the following bin and selectable ice components;

Bin components:

• Entire bin

• Paddle wheel

• Paddle wheel area

•Agitator

• Paddle wheel pin

sodium hypochlorite) with 2 gallons of 120°F water. The mixture should not exceed 100 PPM of chlorine. Or mix a solution of any approved sanitizer, following the directions for mixing and applying the sanitizer.

7. Sanitize the ice bin and cold plate with the sanitizing solution for at least 10 seconds.

8. Allow to air dry. Do not rinse.

9. Re-assemble all bin and selectable ice parts once dry and hand tighten all knurled fasteners.

10. Pour in fresh, sanitary ice and replace the plastic lid on the top of the dispenser.

11. Plug in the unit’s electrical cord.

12. Check for proper ice dispensing.

CLEANING CHECKLIST

•Check CO

supply . If CO2 supply is low, an arrow on

the primary regulator gauge will point to a shaded area that reads “Low CO

” or “Change CO2

Cylinder.”

• Check syrup supply.

• Clean drain pan, grid, and splash panel.

• Clean the nozzles.

• Ice Chute

• Rear bushing

• Motor shaft

• Strip lids (where applicable)

Selectable Ice:

(for units with this feature)

• Decorative Chute

•Housing

• Housing Door

• Whole Ice Door

• Sanitary Lever

• Hub/Blade Assembly

•Drip Pan

5. Rinse all the parts in clean, running water.

4-2

Part Number 020003315 1/11

Section 4 Maintenance

Preventive Maintenance

Preventative maintenance is a vital part of keeping your dispenser in top condition. Following the guidelines below will assist you in continued trouble-free operation of your unit.

1. Conduct daily maintenance of the machine.

2. Perform monthly maintenance of the machine.

3. Perform periodic maintenance and sanitizing of beverage system.

4. Do not overfill the dispenser bin with ice.

5. Do not allow the dispenser to sit for prolonged periods of non use with ice in the bin.

6. Most ice dispenser service problems are caused by low usage of the ice dispenser.

7. Do not allow ice to remain in the bin more than a day in order to prevent ice from freezing together and/or stagnant ice.

Possible excess ice storage reasons:

• Storage capacity exceeds daily requirements.

• Low demand during the off season.

• Dispenser oversized with future growth in mind.

Lower ice storage to meet one day’s needs. If you manually fill ice, fill only with the appropriate amount of ice. Fill the dispenser with fresh ice each morning. Do not fill the dispenser at night just before shut down. Ice cubes can freeze together if not dispensed.

Contact MBE at 1-800-367-4233 for more information about our ProActive Maintenance Program.

Disassembly

DISASSEMBLY FOR CLEANING AND MAINTENANCE

NOTE: Sanitize the ice dispenser at Initial Start-up in addition to monthly sanitizing. You will need a slotted screwdriver in order to disassemb le.

Disassemble parts in the following order:

A. Merchandiser B. Ice chute C. Hitch Clip Pin D. Agitator

E. Paddle wheel

F. Bin liner

G. Paddle wheel area

Beverage/Ice Dispenser

Accessing a Dispenser Bin Top Mounted with a Manitowoc ice machine:

1. Remove the front panel of the ice machine.

2. Remove the ice deflection baffle. This will give you access to the dispenser bin.

3. If the Manitowoc ice machine is operating, wait for the sheet of ice to fall into the dispenser bin.

When the ice sheet falls into the dispenser bin, immediately place toggle switch of the ice machine to the OFF position. If the Manitowoc ice machine is NOT operating, place the toggle switch of the ice machine to the OFF position.

4. On models without a top mounted ice machine, remove the plastic lid from the top of the dispenser.

5. Remove all ice from the dispenser.

6. Disconnect electric al po we r to the dispenser.

7. Remove agitator arm and paddlewheel pi n.

Part Number 020003315 1/11 4-3

Maintenance Section 4

Hitch Clip Pin Agitator Bar

Paddle Wheel

Mushroom Bushing

Front Serviceable Motor

a. With agitator arm in any position remove hitch

clip pin from the mushroom bushing on the rear of the ice bin.

b. Push the agitator bar toward the bushing to

remove it from the paddle wheel hub.

NOTE: If a top mount ice machine is installed, sliding the ice machine to one side will make bin component removal easier. If the ice machine is hard plumbed it will need to be disconnected.

FRP-250 (NON-CRUSHER) DISASSEMBLE THE ROCKING CHUTE

1. Loosen the two knurled fasteners that hold the merchandiser in place.

2. Remove the merchandiser.

3. Remove outer bracket.

4. Remove door lock.

5. Remove door.

6. Remove ice chute.

Front Serviceable

8. Remove paddle wheel, bin liner and paddle wheel area.

9. Move the front of the agitator to one side and slide the agitator forward until the rear of the agitator shaft is clear of the bushing.

10. Remove the agitator from the bin area.

11. Slide the paddle wheel from its shaft.

12. Loosen the four knurled fasteners that hold the bin liner in place.

13. Remove the bin liner.

14. Remove the paddle wheel area from the bin.

15. Discard the remaining ice in the bin.

Ice Chute Removal

4-4

Part Number 020003315 1/11

Section 4 Maintenance

Crusher Housing

Housing Door

Hub Blade Assembly

Drip Pan

Decorative Chute

Sanitary Lever

Cotter Pin

Chute Rod

Decorative Chute

Drip Pan

Housing Door

Motor Mount

Housing Mount

Solenoid Arm

Locking Tab

Crusher Housing

Hub/

Blade

Assembly

SELECTABLE ICE CRUSHER DISASSEMBLY

On units equipped with the selectable ice option, be fore servicing or cleaning any part of the Selectable Ice unit be sure to unplug it from its power source. In order to access the module and crusher you must first remove the merchandiser by taking out the two screws located at the top of the merchandiser. Once the screws are removed, rotate the top of the merchandiser towards you and then lift the merchandiser up to remove from unit.

3. Remove the Ice Chute by pulling the cotter pin out on the right side of the chute rod and pulling the chute rod toward the left side of the dispenser.

4. Remove the crushed ice and cube ice doors from the dispenser by lifting the solenoid arms up and pushing the doors back to disengage the door fro m the solenoid arm.

1. Unplug unit before cleaning or servicing the Crusher Assembly.

2. Remove the merchandiser by taking out the two screws located at the top of the merchandiser . Once the screws are removed rotate the top of the merchandiser towards you and then lift the merchandiser up to remove from unit.

NOTE: When the Merchandiser is removed an electrical safety switch disconnects power to the Ice Crusher assembly.

5. Remove the Crusher Drip Pan by pulling it forward.

6. Remove the ice crusher blade assembly from the crusher housing.

A. Unlock the Crusher Hub/Blade assembly from

the Crusher Housing by pushing locking tab in, and rotating the Hub/Blade assembly clockwise.

Part Number 020003315 1/11 4-5

Maintenance Section 4

Hub/Blade

Assembly

Crusher Housing

Axle

Knob

Hub/Blade Assembly

Crusher Housing

Axle

Knob

Stationary Blades

Locking Tab

Crusher Housing

Hub/

Blade

Assembly

Cotter Pin

Chute Rod

Decorative Chute

B. Pull the Hub/Blade assembly out of the hous ing

approx. ½” to disengage the Crusher Axle from the motor shaft.

C. Rotate the knob on the Crusher Axle so it is in a

vertical position. (This will assure the rotating blades will not interfere with pulling the Hub/ Blade assembly from the housing.)

D. Now the Hub/Blade assembly will be free from

the housing and you will be able to completely remove the Hub/Blade assembly from unit.

REASSEMBLE THE ICE CRUSHER ASSEMBLY

rotating blades with the Housing to assure a quick and easy installation.

3. Once all blades are in the Crusher Housing you will need to align the Crusher Axle with the motor shaft. You can do this by turning the Axle Knob and pushing the blade assembly toward the motor until the Hub/Blade assembly is flush with the end of the Crusher Housing.

4. To lock the Hub/Blade assembly into the housing, rotate the Crusher Hub/Blade assembly counter clockwise until the locking tab snaps into place and the Crusher Hub/Blade assembly is secure.

5. Replace the Crusher Drip Pan.

1. Insert the Hub/Blade assembly into the Ice Crusher Housing. When inserting the Hub/Blade assembly you must align the Stationary blades with the locating slots in the Ice Crusher Housing.

2. When inserting the Hub/Blade assembly into the Ice Crusher Housing you must also make sure the Axle Knob is in a vertical position. This will align the

4-6

6. Reattach the Decorative Ice Chute by inserting the chute rod through the Decorative Chute, Housing Mount, and Motor Mount. Secure the Chute Rod by inserting the cotter pin through the rod on the right side of the chute.

7. Ensure the extension at the top of the Decorative Chute is behind the arm of the Activation Switch.

Part Number 020003315 1/11

Section 4 Maintenance

Pins

SERVICEABLE GEAR MOTOR REMOVAL

These instructions are provided as a guide for the removal of the gear motor. Depending on the model number of your dispenser, these instructi ons may vary slightly.

1. Unplug the dispenser.

2. Unplug the motor.

3. Remove motor mount pins.

4. Slide motor towards you.

5. Notice alignment of the chamfered edge of drive shaft.

6. New motor must have the same alignment (within 15 degrees).

7. To get correct alignment you can do one of two things:

a. Turn drive shaft with an adjustable wrench,

being careful not to damage the drive shaft.

b. Plug in the unit, plug in the motor and use the

ice dispense switch to move the drive shaft into correct alignment.

8. If you plugged in the unit to help with alignm en t of drive shaft now unplug the unit.

9. Slide motor up into housing, making sure that the tabs fit on the bracket.

10. Install motor mount pins.

11. Plug in motor.

12. Test unit.

Part Number 020003315 1/11 4-7

Maintenance Section 4

Warning

Bag side

connector

Sanitizing

BEVERAGE SYSTEM CLEANING

Flush sanitizing solution from syrup system. Residual sanitizing solution left in system could

create a health hazard.

2. Disconnect the “syrup-line side” of the BIB When using cleaning fluids or chemicals, rubber gloves and eye protection must be worn .

Sanitize the beverage system at initial start-up as well as regularly scheduled cleaning. The drain pan must be in place under soda valves, to carry away detergent and sanitizing agents that will be flushed through valves.

BAG-IN-BOX SYSTEM SANITATION

connector.

The procedure below is for the sanitation of one syrup circuit at a time. Repeat to sanitize additional circuits.

You will need the following items to clean and sanitize the Bag-in-Box (BIB) beverage system:

• Three (3) clean buckets

• Plastic brush or soft cloth

• Mild detergent

• Unscented bleach (5% Na CL O) or Commercial sanitizer

• Bag-In-Box bag connector

1. Prepare the following in the buckets:

• Bucket 1 — warm to hot tap water for rinsing.

• Bucket 2 — mild detergent and warm to hot water.

• Bucket 3 — mix a solution of unscented bleach (5% Na CL O) or commercial sanitizer an d warm to hot water. Mixture sho uld supply 100 PPM available chlorine (1/4 oz. bleach to 1 gallon water).

3. Rinse connector with warm tap water.

4. Connect syrup connector to BIB connector and immerse both into Bucket 1. A “bag-side” connector can be created by cutting the connector from an empty disposable syrup bag.

4-8

Part Number 020003315 1/11

Section 4 Maintenance

Caution

5. Draw rinse water through system until clean water is dispensed. Most beverage valves allow the syrup side to be manually activated by depressing the syrup pallet.

6. Connect Bucket 2 to system.

7. Draw detergent solution through system until solution is dispensed.

8. Repeat steps 2-7 until all syrup circuits contain detergent solution.

9. Allow detergent solution to remain in the system for 5 minutes.

10. Connect Bucket 3 to system.

11. Draw sanitizing solution through system until solution is dispensed.

12. Repeat step 11 until all syrup circuits contain sanitizer solution.

13. Allow sanitizer solution to remain in system for 15 minutes.

14. Remove nozzles and diffusers from beverage valves.

15. Scrub nozzles, diffusers and all removable valve parts (except electrical parts) with a plastic brush or a soft cloth and the detergent solution.

16. Soak nozzles, diffusers and removable valve parts (except electrical parts) in sanitizer for 15 minutes.

17. Replace nozzles, diffusers and valve parts.

18. Connect Bucket 1 to system.

19. Draw rinse water through system until no presence of sanitizer is detected.

20. Attach syrup connectors to BIBs.

21. Draw syrup through system until only syrup is dispensed.

22. Discard first 2 drinks.

FIGAL BEVERAGE SYSTEM

1. Prepare the following in three clean Figal tanks:

• Rinse tank - fill with room temperature tap water.

• Detergent tank - mix approved beverage system cleaner with warm water as directed.

• Sanitizing tank - mix a solution of unscented bleach (5% Na CL O) or commercial sanitizer and warm to hot water. Mixture should supply 100 PPM available chlorine (1/4 oz. bleach to 1 gallon water).

2. Disconnect all product and water lines from product tanks and remove carbonator.

3. Locate the Figal syrup tank for the circuit to be sanitized. Remove both quick disconnects from the Figal syrup tank. Rinse quick disconnects in tap water.

4. Connect rinse tank to the syrup line. Draw clean rinse water through the valve until syrup is flushed from the system.

5. Connect detergent tank to the syrup line and draw detergent through the valve for two minutes. Then, allow remaining detergent to stay in the system for five minutes.

6. Connect rinse tank to the syrup line. Draw clean rinse water through the valve until detergent is flushed from the system.

7. Remove valve nozzle and diffuser as shown in Daily Cleaning instructions. Using a plastic brush or a so ft cloth and warm water , scrub the nozzle, dif fuser , bottom of the dispensing valve and cup lever , if applicable.

8. Place removable valve part s (EXCEPT solenoids) in sanitizing solution for 15 minutes.

9. Replace valve diffuser and nozzle on the beverage valve.

10. Connect sanitizer tank to the syrup line and draw sanitizer through the valve for two minutes. Allow sanitizer to remain in the system for a minimum of 15 minutes.

1 1. Reconnect syrup and carbonated water lines.

12. Draw syrup through the lines to rinse the system. Discard drinks until at least two cups of satisfactory tasting beverage are dispensed through the valve.

Part Number 020003315 1/11 4-9

Shipping, Storage and Relocation

Before shipping, storing, or relocating this unit, syrup systems must be sanitized. After sanitizing, all liquids (sanitizing solution and water) must be purged from the unit. A freezing environment causes residual sanitizing solution or water remaining inside the unit to freeze, resulting in damage to internal components.

Maintenance Section 4

FRP-250 Graphic Medallion Removal & Installation

The graphic medallions on the FRP-250 are made out of a flexible duratran that can be removed/replaced from the front of the unit without the use of tools (back-lit merchandiser light bo x does not need to be removed fr om the unit).

MEDALLION REMOVAL

1. With Palm of hand slide graphic to the left to expose narrow seam on right edge.

2. In the newly exposed gap, peel the medallion out toward you and grasp the right edge of graphic while pulling / flexing it toward you to release the 3 upper and lower tabs.

3. Continue to pull graphic toward you while slightly moving it to the right to release the rest of the graphic from the left side of the merchandiser until the medallion is completely free from the merchandiser.

MEDALLION INSTALLATION

1. Facing the unit, start slightly off center to the right of the merchandiser medallion area by holding the graphic medallion with one hand on each side at about the 9 & 3 o’clock position. Slide / insert the 3 bottom tabs under the bottom edge of the merchandiser.

2. With the bottom tabs in place with push down on the top of the medallion flexing it into a slight “C” shape so the top 3 tabs can be inserted under the top edge of the merchandiser.

3. With the top tabs in place smooth the medallion out of the “C” shape and use the palm of you hand to seat the graphic under the left and right edges.

4-10

Part Number 020003315 1/11

Section 5 Before Calling for Service

Section 5

Before Calling for Service

Checklist

If a problem arises during operation of your dispenser, follow the checklist below before calling service. Routine adjustments and maintenance procedures are not covered by the warranty.

Problem Possible Cause To Correct

Dispenser will not dispense ice (and NO SOUNDS are heard when machine is activated).

Dispenser will not dispense ice (motor runs but no ice movement is heard in bin).

Excessive clustering or bridging of ice. Loaded ice not broken up. (Caution:

Ice dispenses continuously. Misaligned microswitch. Adjust microswitch.

Thumping noise or irregular sound at a particular area of the dispenser.

Dispensing crushed ice or reduced dispensing speed.

Door will not close. Ice jammed in chute. Adjust bridge in ice machine or, when

Mounting brackets for rocking chute have spread too far apart.

No power. Check electrical connection. Loose wire in electrical system. Thoroughly check all wire connections. Dispenser overloaded with ice. Remove ice from dispenser until unit will

operate.

Motor not working. Check thermally protected motor.

Replace motor or capacitor if necessary. No ice in bin. Fill dispenser with ice. Door not opening. Check rocking chute mechanism or

electric solenoid operation. Paddle wheel pin slipped from the paddle

wheel.

Super cooled ice is not covered by the Servend warranty.)

Excessive water spilling from the ice machine.

Poorly adjusted ice machine. Adjust ice machine to eliminate large

Extremely low usage of the dispenser. Lower the ice level in the bin.

Agitation timer set incorrectly. Test agitation timer. Shaved ice clusters in the bin. Remove clusters, discover why ice is

Water spillage from ice machine into dispenser bin.

Agitation timer. (FRP-250) Test agitation timer. Bridge of ice sheet is too thick. Adjust ice machine. Paddle wheel area broken or cracked. Replace paddle wheel area. Ice clusters in bin. Break up or remove clusters. Door not fully open. Adjust door.

Door and/or door lock has come out of place.

Stretched during removal for cleaning or maintenance.

Replace paddle wheel pin.

Break ice clusters before manually filling

the dispenser. (See ice

recommendations.)

Adjust ice machine to eliminate water

spillage.

waffle shapes.

shaving, and then repair.

Adjust ice machine.

manually filling, break up clusters.

Replace door and lock into proper

position.

Bend parts into shape.

Part Number 020003315 1/11 5-1

Before Calling for Service Section 5

SELECTABLE ICE TROUBLESHOOTING

Problem Possible Cause To Correct

DISPENSER DOES NOT DISPENSE CRUSHED ICE.

Nothing is heard.

Crusher motor hums but does not turn. Blades obstructed. Check for obstructions in ice crusher

Crusher dispense door does not open. Door solenoid faulty Replace Solenoid

Gear box on motor Gear box on motor faulty. Replace Ice Crusher Motor Assembly

Crusher Motor turns but Gear Motor for Paddle wheel/Agitator Bar does not turn.

Nothing on dispenser works. No power to dispenser Check power source

Difficulty inserting Blade/Hub Assembly into Crusher housing

Crushed Ice dispenses continuously, or by itself.

No flashing lights on keypad, Fluorescent light was on, crusher and whole ice dispenser will not function, transformer breaker blown.

No power. Check power source and power cord. Loose wire in electrical system. Check wiring. Dispense switch faulty Replace switch Crusher Motor Faulty. Replace Motor/Gear Box. Dispenser Safety Switch Open. Assure Merchandiser is installed

correctly with the safety switch in the closed position.

housing. Motor faulty Replace Motor Faulty start relay/capacitor Check relay/capacitor and replace if bad.

Loose wiring to solenoid Check wiring

Crusher Axle broken Replace Crusher Axle Agitator Gear Motor faulty. Replace Agitator Gear Motor. Loose wiring. Check wiring Obstruction in Ice bin stopping motor Check for obstruction

Dispenser Safety Switch opens Assure Merchandiser is installed

correctly with the safety switch in the

closed position. Loose wiring Check wiring. a. Stationary Blades not aligned with

locating slots at top and bottom of crusher housing

b. Rotating Blades not in vertical position. c. Check for ice in Crusher Housing. Ice Dispense Switch Faulty Adjust bridge in ice machine or, when

Water shorted out wiring harness on valves only.

See ""How to Disassemble for

Maintenance"" section in this manual.

manually filling, break up clusters.

Clean up water and reset transformer.

(For units with this feature)

5-2

Part Number 020003315 1/11

Section 5 Before Calling for Service

Drink T roubleshooting

Condition Investigation Check Correction

Water only dispensing No pressure Regulator(s) out of adjustment Check/adjust regulator(s).

Install fresh tank.

line pinched, kinked or

Check/repair/replace CO2 line.

or reset breaker.

Replace water filter. Check/clean/replace pump strainer. Check/clean/repair water check valve. Check for frozen water line. Internal

carbonator unit only.

motor, electrode or liquid level control.

Install fresh tank.

line pinched, kinked or

Check/repair/replace CO2 line.

Adjust CO

pressure due to leaks Repair CO2 leaks.

Clean out the lines.

if necessary.

replace regulator if necessary.

pressure or change the tank.

pressure or replace regulator

supply. Reset pressure or

Syrup and CO

only

Carbonator No power Check power supply. Plug in carbonator

dispensing

Syrup and plain water

No pressure Out o f CO

only dispensing setting

One valve will not dispense anything

Beverage dispensed is too sweet

Beverage is not sweet enough

Is there power to the valve?

Is the ratio (brix) of the drink correct?

Drinks are foaming Are system pressures

correct?

No water, syrup or gas dispensing

Is there power to the unit?

Is power coming through the key switch?

Is there power to the key switch?

Out of CO Defective regulator(s) Check/repair/replace regulator(s). CO

obstructed

Water supply Make sure water is turned “on”.

Defective carbonator Check/repair/replace carbonator pump,

HP regulator out of adjustment Adjust HP regulator to the proper setting. Defective HP regulator Check/repair/replace HP regulator. CO

obstructed Broken wire or loose connection Replace/repair wire or connector. Bad microswitch Replace microswitch. Flow control out of adjustment Adjust the flow control. Insufficient soda flow due to low

carbonator pressure Low CO Obstruction in the water or soda

line Flow control out of adjustment Adjust the flow control. Soda flow too high Reset CO

Obstruction in syrup line Clean out the syrup line. Over carbonation Check CO

Dirty lines/valves Clean/sanitize entire system. No power Plug in unit or reset breaker. Power to control box Replace fuse or control box. Key switch “off” Turn switch “on”. Key switch defective Replace key switch.

No power through the transformer Reset/replace transformer.

Part Number 020003315 1/11 5-3

Before Calling for Service Section 5

1. Remove probe electronics.

2. Pass magnetic tip of screwdriver by lower end of tube extending from electronics package.

3. Reed switch will close.

4. Carbonator operates.

Flavor Shot T roubleshooting

Problem Possible Ca use Corrective Action

Flavor shot syrup does not dispense when flavor button is depressed.

No power to control board. Disconnected or loose wires. Check connector to transformer and corresponding

Flavor syrup does not shut off. Check for stuck solenoid Replace solenoid if it continues to stick.

Syrup supply depleted. Replace syrup.

2 supply depleted. Replace CO2.

CO BIB disconnect loose or packed

with dried syrup residue. CO

2 Regulator set to low. Check CO2 regulator for proper setting — 30 PSI (1

Kinked CO BIB pump inoperative. Check pumps, replace if needed. Valve solenoid inoperative. Check wiring to valve, replace solenoid. Vinyl tubing off at nozzle or at

solenoid. Vinyl tubing plugged with syrup at

nozzle or at solenoid. Board not in dispense mode. Place control board into dispense mode “0”.

No power to transformer. Check power supply at transformer — 24 VAC.

2 or syrup line. Check lines for kinks.

Tighten and/ or clean BIB disconnect.

Bar) or according to line run.

Reconnect tubing.

Clean tubing and nozzle.

control board.

Pump Troubleshooting

Problem Possible Cause Corrective Action

Pump motor does not shut off

Pump motor intermittent

Pump motor does not pump

Problem with probe or probe harness.

Problem with probe or probe harness

Water pressure from water source is not high enough

Verify water pressure leading into pump inlet is 40 psi

minimum.

5-4

Part Number 020003315 1/11

may necessitate change of specifications without notice.

Part Number 020003315 1/11

Manitowoc Beverage Equipment

2100 Future Drive

Sellersburg, IN 47172, USA

Ph: 812-246-7000 Fax: 812-246-7024

Visit us online at: www.manitowocfsg.com

Manitowoc FRP-250, FRP-250SCI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual