Page 1
MH-178921_UM-1117_REV-5.01
2D Mini Barcode Scanner
User Manual
Model 178921
manhattanproducts.com
Page 2
2D Mini Barcode Scanner—178921 User Manual
2
Before You Begin
Read through this manual carefully before using the product and operate it according to the manual.
Keep it in an easily accessible location for future reference.
Do not disassemble the device or remove the seal label from the device. Doing so will void the
Manhattan product warranty.
All pictures in this manual are for reference only. The actual product may differ. Manhattan reserves the
right to make changes to any software or hardware to improve reliability, function, or design at any time
without notice. The information contained herein is subject to change without prior notice.
No user, corporation or individual, shall duplicate, in whole or in part, distribute, modify, decompile,
disassemble, decode, reverse engineer, rent, transfer or sublicense such software without prior written
consent from the copyright holders.
This manual is copyrighted. No part of this publication may be reproduced, distributed or used in any
form without written permission from Manhattan Products.
Version History
Version Description Date
V1.0
Initial Release
June 28, 2016
Page 3
2D Mini Barcode Scanner—178921 User Manual
3
TABLE OF CONTENTS
CHAPTER 1: GETTING STARTED ......................................................................................................................... 5
INTRODUCTION ................................................................................................................................................................ 5
FEATURES ........................................................................................................................................................................ 5
BARCODE OVERVIEW AND SCANNING PROCEDURE ................................................................................................................ 5
CHAPTER 2: SCANNER PARAMETERS ................................................................................................................. 6
PHYSICAL PARAMETERS ..................................................................................................................................................... 6
PERFORMANCE PARAMETERS ............................................................................................................................................. 6
DEPTH OF FIELD ............................................................................................................................................................... 7
USER ENVIRONMENT ......................................................................................................................................................... 7
CHAPTER 3: WIRELESS SETTINGS ....................................................................................................................... 8
BLUETOOTH BARCODE SCANNER PAIRING ............................................................................................................................ 8
BLUETOOTH MODES ......................................................................................................................................................... 8
FUNCTIONAL MODES ........................................................................................................................................................ 8
CHAPTER 4: SYSTEM SETTINGS ........................................................................................................................ 10
BUZZER SETTING ............................................................................................................................................................ 10
STAND-BY TIME .............................................................................................................................................................. 11
SCANNING MODE ............................................................................................................................................................ 11
RETURN TO FACTORY DEFAULT ........................................................................................................................................ 12
ILLUMINATION LED ........................................................................................................................................................ 12
BARCODE SCANNING DELAY ............................................................................................................................................ 12
COUNTRY/LANGUAGE KEYBOARD ..................................................................................................................................... 13
CHECK THE VERSION ....................................................................................................................................................... 14
CHAPTER 5: CUSTOMIZED DATA INCLUSION .................................................................................................. 15
INTRODUCTION .............................................................................................................................................................. 15
TERMINATING CHARACTER SETTING .................................................................................................................................. 15
SETTING A CUSTOM PREFIX OR SUFFIX ............................................................................................................................... 15
CHAPTER 6: SYMBOLOGIES .............................................................................................................................. 17
INTRODUCTION .............................................................................................................................................................. 17
GENERAL SETTING .......................................................................................................................................................... 17
EAN-8 .......................................................................................................................................................................... 17
EAN-13 ........................................................................................................................................................................ 19
CODABAR ...................................................................................................................................................................... 20
CODE 39 ....................................................................................................................................................................... 20
CODE 93 ....................................................................................................................................................................... 21
CODE 128 ..................................................................................................................................................................... 22
GS1-128 ...................................................................................................................................................................... 22
UPC-A ......................................................................................................................................................................... 22
UPC-E .......................................................................................................................................................................... 23
INTERLEAVED 2 OF 5 ....................................................................................................................................................... 25
INDUSTRIAL 2 OF 5 ......................................................................................................................................................... 25
MATRIX 2 OF 5 ............................................................................................................................................................... 26
Page 4
2D Mini Barcode Scanner—178921 User Manual
4
MSI .............................................................................................................................................................................. 26
TELEPEN ........................................................................................................................................................................ 26
CHINA POSTAL CODE ...................................................................................................................................................... 27
QR CODE ...................................................................................................................................................................... 27
DATA MATRIX ................................................................................................................................................................ 28
PDF 417 ....................................................................................................................................................................... 28
MICRO PDF 417 ............................................................................................................................................................ 28
MAXI CODE .................................................................................................................................................................... 29
AZTEC ........................................................................................................................................................................... 29
HANXIN ......................................................................................................................................................................... 30
APPENDICES ..................................................................................................................................................... 31
APPENDIX A: BYTE BITS ................................................................................................................................................... 31
APPENDIX B: ASCII TABLE ............................................................................................................................................... 32
ADDITIONAL INFORMATION ............................................................................................................................ 37
Page 5
2D Mini Barcode Scanner—178921 User Manual
5
Chapter 1: Getting Started
Introduction
The Manhattan 2D Mini Barcode Scanner offers a new, compact design that is useful for stocktaking,
warehouse and logistics applications. Its 2D linear imager allows the scanning module to deliver
excellent decoding performance in reading most 1D and 2D barcodes.
Small in volume and lightweight in construction, the scanner can be easily carried in a pocket or bag for
enhanced mobility. Bluetooth technology lets it easily connect to most Android and iOS mobile devices.
Scanned data can be transferred to a host device in real time or stored in the device's built-in memory for
uploading later.
Features
• Image Scanning: quick and easy decoding of most 1D, 2D, printing, paper and screen codes with
added ability to read poorly printed or smudged codes
• Wireless Bluetooth communication: supports mainstream Android and iOS systems, PCs, tablets,
laptops and computers
• Automatic reconnection when offline
• Low physical volume for easy carrying or wearing
• Stable and safe data storage, supporting HID and SPP modes
Applications
• Retail
• Manufacturing
• Electronic Coupons
• Mobile Payments
• Logistics
Barcode Overview and Scanning Procedure
Manual Introduction
Manual scanning mode:
1. Press and hold the trigger button; the red light activates.
2. Position the center of the codes under the light, and move the scanner between the codes to find
the best scanning distance.
3. Decoding (reading) is complete when the buzzer sounds and the lights turn off. Codes are
transmitted to the host.
Note: Increase scanning success by finding and maintaining the right reading distance from the same
types of barcodes.
Page 6
2D Mini Barcode Scanner—178921 User Manual
6
Chapter 2: Scanner Parameters
Physical Parameters
Performance Parameters
Physical Parameter Value
Weight (USB)
< 70 g / 2.5 oz. (without cable)
Device Dimension
99 (L) x 46 (W) x 21 (H) / 3.9 (L) x 1.8 (W) x 0.8 (H) in.
Material
ABS
Color
Black and Light Blue
Interface
USB
Cable Length
80 cm / 31.5 in. (for charging)
Performance Parameter
Value
Light Source
617 nm LED (aimer), 6500K LEDs (illumination)
Sensor
640 (H) x 480 (V) CMOS
Processor
ARM 32-bit
Resolution
≥ 5 mil (0.127 mm) @ PCS 90%
Depth of Field
40 –500 cm (1.6 – 19.7 in.)
Scanning Mode
Trigger mode
Decode Angle
Roll: 0-360°; Pitch: ± 65° or greater; Yaw: ± 60° or greater
Transmission Distance
30 m (98 ft.)
Battery Capacity
1000 mA
Power Supply
5 VDC @130 mA
Transmission Type
Bluetooth 3.0
Print Contrast
≥ 25%
Ambient illumination
100,000 Lux Max
Decode Capability
1D: EAN-8, EAN-13, Codabar, CODE 39, CODE 93, CODE 128, China
Post, GS1-128, UPC-A, UPC-E, ISBN/ISSN, ISBT, Interleaved 2 of 5,
Standard 2 of 5, Matrix 2 of 5, Industrial 2 of 5, MSI, RSS, ITF14,
Telepen, etc.
2D: QR Code, Micro QR Code, Data Matrix, PDF417, Micro PDF 417,
Maxicode, Aztec, Hanxin, etc.
Page 7
2D Mini Barcode Scanner—178921 User Manual
7
Depth of field
Range of decoding
Code Code Dimension Nearest Farthest
Code 39
0.127 mm (0.01 in.) 50 mm (2 in.) 90 mm (3.5 in.)
Code 39
0.5 mm (0.2 in.) 40 mm (1.6 in.) 200 mm (7.9 in.)
UPC-A
0.33 mm (0.01 in.) 40 mm (1.6 in.) 180 mm (7.1 in.)
QR Code
0.5 mm (0.2 in.) 40 mm (1.6 in.) 200 mm (7.9 in.)
Data Matrix
0.3 mm (0.1 in.) 40 mm (1.6 in.) 110 mm (4.3 in.)
PDF 417
.17 mm (.01 in.) 50 mm (2 in.) 90 mm (3.5 in.)
Test condition: 25°C (77°F) indoor, ambient illumination 200 Lux, PCS = 0.9
User Environment
User Environment Value
Operating Temperature
0 to 50°C (32 – 122°F)
Storage Temperature
-40 to 60°C (-40 – 140°F)
Relative Humidity
5% to 95% (non-condensing)
IP Level
IP42
Drop Test
1.5 m (4.9 ft.)
Temperature Test
30 minutes for high temp., 30 minutes for low temp.
Highest Temp
60°C (140°F)
Lowest Temp
-20°C (-4°F)
Shock Resistance
10 H @ 125 RPM
Page 8
2D Mini Barcode Scanner—178921 User Manual
8
Chapter 3: Wireless Settings
Bluetooth Barcode Scanner Pairing
The Manhattan Wireless 2D Mini Barcode Scanner can be connected to PCs, mobile phones and other
devices according to the user's needs. Scan the programming barcodes to configure the scanner.
EZ Pair
One-key pairing
Pairing the Barcode Scanner
1. Pull the trigger on the scanner for at least eight seconds to turn it on and enter Pairing Mode.
Scan the above code for easy pairing. The blue indicator LED flashes.
♣ If your computer or device does not support Bluetooth technology, insert the Bluetooth
USB dongle into an available port on that device.
2. Open the Bluetooth app on your computer or device; begin the process to Add a Device by
searching for devices.
3. Find "General Bluetooth HID Barcode Scanner" from the available devices list. Double- or
single-click the link to install the driver.
4. A short beep will sound to confirm the device is paired.
5. The blue LED will remain lit to confirm that pairing is complete.
Bluetooth Modes
The Manhattan Wireless 2D Mini Barcode Scanner allows users to choose from two different modes. HID
mode outputs text directly into receptive fields on a computer or mobile device. SPP mode outputs data
through serial port simulation mode (requires serial software tools to receive data)
%%BT_HID %%BT_SPP
SPP MODE HID MODE*
Functional Modes
Normal Mode
This function transmits barcode data to the computer/device in real time.
%%ALLPT-SET
Normal Mode
Page 9
2D Mini Barcode Scanner—178921 User Manual
9
Offline Mode
This function uploads data normally if the user is in range of computer/device; stores data if out of
range for upload once back in range.
%%ALLAEM-SET
Offline Mode
Inventory Mode
This function retains all scanned barcode data for later upload to a host computer/device.
%%ALLMEM-SET
Inventory Mode
Data Upload
This option uploads scanned and retained data to the computer/device.
%%ALLMEM-SC
Data Upload
Total Quantity of Data
This option reports the number of barcodes scanned that are stored in the scanner.
%%ALLMEM-ZS
Total Quantity of Data
Data Elimination
This option clears all scanned data from the scanner.
%%ALLMEM-QC
Data Elimination
Power Off
This code turns off the scanner immediately.
%%POWEROFF
Power Off
Page 10
2D Mini Barcode Scanner—178921 User Manual
10
Chapter 4: System Settings
Buzzer Setting
Sound On and Off
Buzzer on*
Buzzer off
Buzzer Tone
Low Middle
High*
Number of Buzzers
Once
Twice
Three Times
Four Times
Five Times
Six Times
Page 11
2D Mini Barcode Scanner—178921 User Manual
11
Stand-by Time
The default standby time for this wireless scanner is 20 seconds. Use the programming codes below to
set a different standby time. Begin by scanning the "Start Setting" code. Then, scan the corresponding
time programming code.
%%ALLTIMSET
Start Setting
%%ALLTIM00
20s*
%%ALLTIM01
30s
%%ALLTIM02
60s
%%ALLTIM03
2mins
%%ALLTIM04
5mins
ALLTIM05
10mins
%%ALLTIM06
20mins
Scanning mode
Trigger Mode (Default): sets the scanner to read a barcode once the trigger has been pulled.
Trigger Mode*
Continuous Mode: sets the scanner to keep its red light on to read codes that pass in front.
Auto Continuous Mode
Trigger Specialized for Mobile Screen Codes
Page 12
2D Mini Barcode Scanner—178921 User Manual
12
Return to Factory Default
This option returns the scanner to factory default; used for when the scanner fails to read barcodes, a
different application or configuration is necessary, or to clear out temporary functions.
Restore All Factory Defaults
Illumination LED
This setting affects the brightness of the illumination LEDs when the trigger is pulled.
Illumination Level 4(Default)*
Illumination Level 3
Illumination Level 2
Illumination Level 1
Illumination OFF
Barcode Scanning Delay
This option sets a scanning delay after being triggered.
No Delay
Delay 500ms
Delay 2000ms
Page 13
2D Mini Barcode Scanner—178921 User Manual
13
Country/language Keyboard
Keyboard layouts vary from country to country. All supported keyboard types are listed below.
1-U.S.*
2-U.K.
3-Denmark
4 - France
5-Finland
6-Turkey-F
7-Italy
8-Norway
9-Albania
10-Belgium
11-Bosnia
12-Brazil
13-Croatia
14-Czech
15-Dutch
16-Estonia
Page 14
2D Mini Barcode Scanner—178921 User Manual
14
17-Germany / Austria
18-Greek
19-Hungary
20-Irish
21-Latvia
22-Lithunnia
23-Macedonia
24-Spain
25-Poland
26-Portugal
27-Romania
28-Russia
29-Japan
Check the Version
Check the version
Page 15
2D Mini Barcode Scanner—178921 User Manual
15
Chapter 5: Customized Data Inclusion
Introduction
For some applications, users may wish to include additional information/functionality such as barcode
type, data acquisition time or a delimiter to the barcode data. The functions here can attach customized
prefix and suffix information to the barcode's scanned data or move the cursor to a new field or line
without changing the barcode data itself.
Note: Customized data — <Prefix><Data><Suffix><Terminating Characters>
Terminating Character Setting
These codes instruct the host device's cursor to move to a new position in the data fields once a scan has
been completed.
Add Return CR* Add Newline LF
Add Return + Newline Add TAB (HT)
Setting a Custom Prefix or Suffix
This function enables users to add customized prefix and suffix information to the standard barcode data.
For example, the host device/computer reports “VC123" before scanned barcode data when the user
scans the barcodes for “V,” “C,” “1,” “2” and “3" in the prefix setting. Likewise, the host device/computer
reports “123DE” after scanned barcode data when the user scans the barcodes for “D,” “E,” “1,” “2” and “3”
in the suffix setting.
Set Custom Prefix
To set a custom prefix, refer to Appendix B and determine the hexadecimal values that will create it.
Then, scan “Set Custom Prefix.” Next, scan Byte Bit "9" (Appendix A) twice before scanning the
corresponding Byte Bits that represents the hexadecimal values of the desired suffix. Finally, scan
“Save.”
Example: Set the custom prefix “OK”:
A. Check the hex value of “OK” in the ASCII table (“OK”: 4F 4B);
B. Scan “Set Custom Prefix” programming code;
C. Scan the numeric barcodes “9”, “9”, “4”, “F”, “4”, “B” in Appendix A;
D. Scan “Save."
Page 16
2D Mini Barcode Scanner—178921 User Manual
16
Set Custom Prefix
Save
Don’t Save
Set Custom Suffix
To set a custom suffix, refer to Appendix B and determine the hexadecimal values that will create it.
Then, scan “Set Custom Suffix.” Next, scan Byte Bit "9" (Appendix A) twice before scanning the
corresponding Byte Bits that represents the hexadecimal values of a desired suffix. Finally, scan
“Save.”
Example: Set the custom Suffix “VC”:
A. Check the hex value of “VC” in the ASCII table (“VC”:56 43);
B. Scan “Set Custom Suffix” programming code;
C. Scan the numeric barcodes “9”, “9”, “5”, “6”, “4”, “3”in Appendix A;
D. Scan “Save."
Set Custom Suffix
Save
Don’t Save
Save and Clear
This code clears all prefixes and suffixes you have set, excluding Terminating Characters.
Clear all Prefixes and Suffixes*
Page 17
2D Mini Barcode Scanner—178921 User Manual
17
Chapter 6: Symbologies
Introduction
Every symbology (barcode system) has its own attributes. The programming barcodes that follow will
configure the scanner so it can read them. Manhattan recommends disabling those that are rarely used
to increase the efficiency of the scanner.
General Setting
If the “Disable All Symbologies” feature is enabled, the scanner will not be able to read scannable
barcode data — only the programming codes.
Enable All Symbologies Disable All Symbologies
EAN-8
Restore Factory Defaults
Restore the Factory Defaults of EAN-8
Note on Add-on Codes: many barcodes are augmented with a two- or five-digit add-on code, which forms
a new code. In the examples below, the part surrounded by the blue line is a standard barcode while the
part surrounded by the red line is the add-on code. An asterisk underneath the codes "Enable" or
"Disable" codes notes the default mode.
Page 18
2D Mini Barcode Scanner—178921 User Manual
18
Enable/Disable EAN 8
Enable EAN-8*
Disable EAN-8
Transmit Check Digit
EAN-8 is eight digits in length with the last one as its check digit, which verifies data. The default
mode transmits the EAN-8 check digit.
Transmit EAN-8 Check Digit*
Do Not Transmit EAN-8 Check Digit
Add-On Code
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code *
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code *
EAN-8 Addenda Separator
This option adds a space between the main barcode data and the added-on barcode data. When
disabled, no space is added.
Enable EAN-8 Addenda Separator*
Disable EAN-8 Addenda Separator
Page 19
2D Mini Barcode Scanner—178921 User Manual
19
EAN-13
Restore Factory Defaults
Restore the Factory Defaults of EAN-13
Enable/Disable EAN 13
Enable EAN-13*
Disable EAN-13
Transmit Check Digit
EAN-13 is 13 digits in length with the last one as its check digit, which verifies data integrity. The
default mode transmits EAN-13 Check Digit.
Transmit EAN-13 Check Digit*
Do Not Transmit EAN-13 Check Digit
Add-On Code
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code*
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code*
EAN 13 Addenda Separator
This option adds a space between the main barcode data and the added-on barcode data. When
disabled, no space is added.
Page 20
2D Mini Barcode Scanner—178921 User Manual
20
Enable EAN13 Addenda Separator*
Disable EAN13 Addenda Separator
Codabar
Restore Factory Defaults
Restore the Factory Defaults of Codabar
Enable/Disable Codabar
Enable Codabar*
Disable Codabar
Start/Stop Characters
Transmit Codabar Start/Stop Character
Don’t Transmit Codabar Start/Stop
Character(Default)*
Code 39
Restore Factory Defaults
Restore the Factory Defaults of Code 39
Page 21
2D Mini Barcode Scanner—178921 User Manual
21
Enable/Disable Code 39
Enable Code 39*
Disable Code 39
Start/Stop Characters
Enable Coda 39 Start/Stop Character
Disable Coda 39 Start/Stop Character*
Enable/Disable Code 39 Full ASCII
This option configures the scanner to identify all ASCII characters.
Enable Code 39 Full ASCII
Disable Code 39 Full ASCII*
Code 93
Restore Factory Defaults
Restore the Factory Defaults of Code 93
Enable/Disable Code 93
Enable Code 93*
Disable Code 93
Page 22
2D Mini Barcode Scanner—178921 User Manual
22
Code 128
Restore Factory Defaults
Restore the Factory Defaults of Code 128
Enable/Disable Code 128
Enable Code 128*
Disable Code 128
GS1-128
Restore Factory Defaults
Restore the Factory Defaults of GS1-128
Enable/Disable GS1-128
Enable GS1-128*
Disable GS1-128
UPC-A
Restore Factory Defaults
Restore the Factory Defaults of UPC-A
Page 23
2D Mini Barcode Scanner—178921 User Manual
23
Enable/Disable UPC-A
Enable UPC-A*
Disable UPC-A
Transmit Check Digit
UPC-A is 12 digits in length with the last one as its check digit, which verifies the data's integrity.
The default mode transmits the UPC-A check digit.
Enable UPC-A Check Digit*
Disable UPC-A Check Digit
Add-on Code
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code *
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code *
UPC-A Addenda Separator
This option adds a space between the main barcode data and the added-on barcode data. When
disabled, no space is added.
Enable UPC-A Addenda Separator*
Disable UPC-A Addenda Separator
UPC-E
Restore Factory Defaults
Page 24
2D Mini Barcode Scanner—178921 User Manual
24
Restore the Factory Defaults of UPC-E
Enable/Disable UPC-E
Enable UPC-E0*
Disable UPC-E0
Enable UPC-E1
Disable UPC-E1*
Transmit Check Digit
UPC-E0 is 12 digits in length with the last one as its check digit, which verifies the data's integrity.
The default mode transmits the UPC-E check digit.
Transmit UPC-E0 Check Digit*
Don’t transmit UPC-E0 Check Digit
Add-on Code
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code*
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code*
UPC-E0 Addenda Separator
This option adds a space between the main barcode data and the added-on barcode data. When
disabled, no space is added.
Enable UPC-E0 Addenda Separator*
Disable UPC-E0 Addenda Separator
Page 25
2D Mini Barcode Scanner—178921 User Manual
25
UPC-E0 Transfer to UPC-A
This option transfers UPC-E to UPC-A. The default does not transfer this data.
Enable UPC-E0 Transfer to UPC-A
Disable UPC-E0 Transfer to UPC-A*
Interleaved 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Enable Interleaved 2 of 5*
Disable Interleaved 2 of 5
Industrial 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Industrial 2 of 5
Enable/Disable Industrial 2 of 5
Enable Industrial 2 of 5
Disable Industrial 2 of 5*
Page 26
2D Mini Barcode Scanner—178921 User Manual
26
Matrix 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Enable Matrix 2 of 5
Disable Matrix 2 of 5*
MSI
Restore Factory Defaults
Restore the Factory Defaults of MSI
Enable/Disable MSI
Enable MSI
Disable MSI*
Telepen
Restore Factory Defaults
Restore the Factory Defaults of Telepen
Page 27
2D Mini Barcode Scanner—178921 User Manual
27
Enable/Disable Telepen
Enable Telepen
Disable Telepen*
China Postal Code
Restore Factory Defaults
Restore the Factory Defaults of Telepen
Enable/Disable China Postal Code
Enable Telepen
Disable Telepen*
QR Code
Restore Factory Defaults
Restore the Factory Defaults of QR Code
Enable/Disable QR Code
Enable QR Code*
Disable QR Code
Page 28
2D Mini Barcode Scanner—178921 User Manual
28
Data Matrix
Restore Factory Defaults
Restore the Factory Defaults of Data Matrix
Enable/Disable Data Matrix
Enable Data Matrix*
Disable Data Matrix
PDF 417
Restore Factory Defaults
Restore the Factory Defaults of PDF 417
Enable/Disable PDF417
Enable PDF 417*
Disable PDF 417
Micro PDF 417
Restore Factory Defaults
Restore the Factory Defaults of Micro PDF 417
Page 29
2D Mini Barcode Scanner—178921 User Manual
29
Enable/Disable Micro PDF 417
Enable Micro PDF 417*
Disable Micro PDF 417
Maxi code
Restore Factory Defaults
Restore the Factory Defaults of Maxicode
Enable/Disable Maxi Code
Enable Maxicode
Disable Maxicode*
Aztec
Restore Factory Defaults
Restore the Factory Defaults of Aztec
Enable/Disable Aztec
Enable Aztec
Disable Aztec*
Page 30
2D Mini Barcode Scanner—178921 User Manual
30
Hanxin
Restore Factory Defaults
Hanxin (Default)
Enable/Disable Hanxin
Enable Hanxin
Disable Hanxin*
Page 31
2D Mini Barcode Scanner—178921 User Manual
31
Appendices
Appendix A: Byte Bits
0 1 2 3
4 5 6 7
8 9 A B
C D E F
Page 32
2D Mini Barcode Scanner—178921 User Manual
32
Appendix B: ASCII Table
HEX
Dec
Char
00 0 NUL (Null char.)
01 1 SOH (Start of Header)
02 2 STX (Start of Text)
03 3 ETX (End of Text)
04 4 EOT (End of Transmission)
05 5 ENQ (Enquiry)
06 6 ACK (Acknowledgment)
07 7 BEL (Bell)
08 8 BS (Backspace)
09 9 HT (Horizontal Tab)
0a 10 LF (Line Feed)
0b 11 VT (Vertical Tab)
0c 12 FF (Form Feed)
0d 13 CR (Carriage Return)
0e 14 SO (Shift Out)
0f 15 SI (Shift In)
10 16 DLE (Data Link Escape)
11 17 DC1 (XON) (Device Control 1)
12 18 DC2 (Device Control 2)
13 19 DC3 (XOFF) (Device Control 3)
14 20 DC4 (Device Control 4)
15 21 NAK (Negative Acknowledgment)
16 22 SYN (Synchronous Idle)
17 23 ETB (End of Trans. Block)
18 24 CAN (Cancel)
19 25 EM (End of Medium)
1a 26 SUB (Substitute)
Page 33
2D Mini Barcode Scanner—178921 User Manual
33
HEX
Dec
Char
1b 27 ESC (Escape)
1c 28 FS (File Separator)
1d 29 GS (Group Separator)
1e 30 RS (Request to Send)
1f 31 US (Unit Separator)
20 32 SP (Space)
21 33 ! (Exclamation Mark)
22 34 " (Double Quote)
23 35 # (Number Sign)
24 36 $ (Dollar Sign)
25 37 % (Percent)
26 38 & (Ampersand)
27 39 ` (Single Quote)
28 40 ( (Right / Closing Parenthesis)
29 41 ) (Right / Closing Parenthesis)
2a 42 * (Asterisk)
2b 43 + (Plus)
2c 44 , (Comma)
2d 45 - (Minus / Dash)
2e 46 . (Dot)
2f 47 / (Forward Slash)
30 48 0
31 49 1
32 50 2
33 51 3
34 52 4
35 53 5
Page 34
2D Mini Barcode Scanner—178921 User Manual
34
HEX
Dec
Char
36 54 6
37 55 7
38 56 8
39 57 9
3a 58 : (Colon)
3b 59 ; (Semi-colon)
3c 60 < (Less Than)
3d 61 = (Equal Sign)
3e 62 > (Greater Than)
3f 63 ? (Question Mark)
40 64 @ (AT Symbol)
41 65 A
42 66 B
43 67 C
44 68 D
45 69 E
46 70 F
47 71 G
48 72 H
49 73 I
4a 74 J
4b 75 K
4c 76 L
4d 77 M
4e 78 N
4f 79 O
50 80 P
51 81 Q
Page 35
2D Mini Barcode Scanner—178921 User Manual
35
HEX
Dec
Char
52 82 R
53 83 S
54 84 T
55 85 U
56 86 V
57 87 W
58 88 X
59 89 Y
5a 90 Z
5b 91 [ (Left / Opening Bracket)
5c 92 \ (Back Slash)
5d 93 ] (Right / Closing Bracket)
5e 94 ^ (Caret / Circumflex)
5f 95 _ (Underscore)
60 96 ' (Grave Accent)
61 97 a
62 98 b
63 99 c
64 100 d
65 101 e
66 102 f
67 103 g
68 104 h
69 105 i
6a 106 j
6b 107 k
6c 108 l
6d 109 m
Page 36
2D Mini Barcode Scanner—178921 User Manual
36
HEX
Dec
Char
6e 110 n
6f 111 o
70 112 p
71 113 q
72 114 r
73 115 s
74 116 t
75 117 u
76 118 v
77 119 w
78 120 x
79 121 y
7a 122 z
7b 123 { (Left/ Opening Brace)
7c 124 | (Vertical Bar)
7d 125 } (Right/Closing Brace)
7e 126 ~ (Tilde)
7f 127 DEL (Delete)
Page 37
2D Mini Barcode Scanner—178921 User Manual
37
Additional Information
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
DISPOSAL OF ELECTRIC AND ELECTRONIC EQUIPMENT
Applicable In The European Union And Other European Countries With Separate Collection Systems
ENGLISH
: This symbol on the product or its packaging means that this product must not be treated as unsorted household waste. In
accordance with EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this electrical product must be
disposed of in accordance with the user’s local regulations for electrical or electronic waste. Please dispose of this product by
returning it to your local point of sale or recycling pickup point in your municipality.
DEUTSCH
: Dieses auf dem Produkt oder der Verpackung angebrachte Symbol zeigt an, dass dieses Produkt nicht mit dem Hausmüll
entsorgtwerden darf. In Übereinstimmung mit der Richtlinie 2012/19/EU des Europäischen Parlaments und des Rates über Elektro- und
Elektronik-Altgeräte (WEEE) darf dieses Elektrogerät nicht im normalen Hausmüll oder dem Gelben Sack entsorgt werden. Wenn Sie
dieses Produkt entsorgen möchten, bringen Sie es bitte zur Verkaufsstelle zurück oder zum Recycling-Sammelpunkt Ihrer Gemeinde.
ESPAÑOL
: Este símbolo en el producto o su embalaje indica que el producto no debe tratarse como residuo doméstico. De
conformidad con la Directiva 2012/19/EU de la UE sobre residuos de aparatos eléctricos y electrónicos (RAEE), este producto eléctrico
no puede desecharse se con el resto de residuos no clasificados. Deshágase de este producto devolviéndolo a su punto de venta o a
un punto de recolección municipal para su reciclaje.
FRANÇAIS
: Ce symbole sur Ie produit ou son emballage signifie que ce produit ne doit pas être traité comme un déchet ménager.
Conformément à la Directive 2012/19/EU sur les déchets d’équipements électriques et électroniques (DEEE), ce produit électrique ne
doit en aucun cas être mis au rebut sous forme de déchet municipal non trié. Veuillez vous débarrasser de ce produit en Ie renvoyant à
son point de vente ou au point de ramassage local dans votre municipalité, à des fins de recyclage.
ITALIANO
: Questo simbolo sui prodotto o sulla relativa confezione indica che il prodotto non va trattato come un rifiuto domestico. In
ottemperanza alla Direttiva UE 2012/19/EU sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE), questa prodotto elettrico
non deve essere smaltito come rifiuto municipale misto. Si prega di smaltire il prodotto riportandolo al punto vendita o al punto di
raccolta municipale locale per un opportuno riciclaggio.
POLSKI
: Jeśli na produkcie lub jego opakowaniu umieszczono ten symbol, wówczas w czasie utylizacji nie wolno wyrzucać tego
produktu wraz z odpadami komunalnymi. Zgodnie z Dyrektywą Nr 2012/19/EU w sprawie zużytego sprzętu elektrycznego i
elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno usuwać jako nie posortowanego odpadu komunalnego.
Prosimy o usuniecie niniejszego produktu poprzez jego zwrot do punktu zakupu lub oddanie do miejscowego komunalnego punktu
zbiórki odpadów przeznaczonych do recyklingu.
WARRANTY INFORMATION
ENGLISH
: For warranty information, go to manhattan-products.com/t/warranty.
DEUTSCH
: Garantieinformationen finden Sie unter manhattan-products.com/t/warranty.
ESPAÑOL
: Si desea obtener información sobre la garantía, visite manhattan-products.com/t/warranty.
FRANÇAIS
: Pour consulter les informations sur la garantie, visitez manhattan-products.com/t/warranty.
POLSKI
: Informacje dotyczące gwarancji znajdują się na stronie manhattan-products.com/t/warranty.
ITALIANO
: Per informazioni sulla garanzia, accedere a manhattan-products.com/t/warranty.
EN MÉXICO
: Póliza de Garantía Manhattan — Datos del importador y responsable ante el consumidor
IC Intracom México, S.A.P.I. de C.V. • Av. Interceptor Poniente # 73, Col. Parque Industrial La Joya, Cuautitlán Izcalli, Estado de México, C.P.
54730, México. • Tel. (55)1500-4500
La presente garantía cubre los siguientes productos contra cualquier defecto de fabricación en sus materiales y mano de obra.
A. Garantizamos los productos de limpieza, aire comprimido y consumibles, por 60 dias a partir de la fecha de entrega, o por el
tiempo en que se agote totalmente su contenido por su propia función de uso, lo que suceda primero.
B. Garantizamos los productos con partes móviles por 3 años.
C. Garantizamos los demás productos por 5 años (productos sin partes móviles), bajo las siguientes condiciones:
1. Todos los productos a que se refiere esta garantía, ampara su cambio físico, sin ningún cargo para el consumidor.
Page 38
2D Mini Barcode Scanner—178921 User Manual
38
2. El comercializador no tiene talleres de servicio, debido a que los productos que se garantizan no cuentan con reparaciones, ni
refacciones, ya que su garantía es de cambio físico.
3. La garantía cubre exclusivamente aquellas partes, equipos o sub-ensambles que hayan sido instaladas de fábrica y no incluye
en ningún caso el equipo adicional o cualesquiera que hayan sido adicionados al mismo por el usuario o distribuidor.
Para hacer efectiva esta garantía bastará con presentar el producto al distribuidor en el domicilio donde fue adquirido o en el domicilio
de IC Intracom México, S.A.P.I. de C.V., junto con los accesorios contenidos en su empaque, acompañado de su póliza debidamente
llenada y sellada por la casa vendedora (indispensable el sello y fecha de compra) donde lo adquirió, o bien, la factura o ticket de
compra original donde se mencione claramente el modelo, número de serie (cuando aplique) y fecha de adquisición. Esta garantía no
es válida en los siguientes casos: Si el producto se hubiese utilizado en condiciones distintas a las normales; si el producto no ha sido
operado conforme a los instructivos de uso; o si el producto ha sido alterado o tratado de ser reparado por el consumidor o terceras
personas.
REGULATORY STATEMENTS
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of Federal
Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the
receiver; connect the equipment to an outlet on a circuit different from the receiver; or consult the dealer or an experienced radio/TV
technician for help.
CE
ENGLISH
: This device complies with the requirements of CE RED 2014/53/EU, 2014/30/EU and/or 2014/35/EC. The Declaration of
Conformity for is available at:
DEUTSCH
: Dieses Gerät enspricht der CE RED 2014/53/EU, 2014/30/EU und / oder 2014/35/EC. Die Konformitätserklärung für dieses
Produkt finden Sie unter:
ESPAÑOL
: Este dispositivo cumple con los requerimientos de CE RED 2014/53/EU, 2014/30/EU y / o 2014/35/EC. La declaración de
conformidad esta disponible en:
FRANÇAIS
: Cet appareil satisfait aux exigences de CE RED 2014/53/EU, 2014/30/EU et / ou 2014/35/EC. La Déclaration de Conformité
est disponible à:
POLSKI
: Urządzenie spełnia wymagania CE RED 2014/53/EU, 2014/30/EU I / lub 2014/35/EC. Deklaracja zgodności dostępna jest na
stronie internetowej producenta:
ITALIANO
: Questo dispositivo è conforme alla CE RED 2014/53/EU, 2014/30/EU e / o 2014/35/EC. La dichiarazione di conformità è
disponibile al:
manhattanproducts.com
North & South America
IC Intracom America
550 Commerce Blvd.
Oldsmar, FL 34677, USA
Asia & Africa
IC Intracom Asia
4-F, No. 77, Sec. 1, Xintai 5th Rd.
Xizhi Dist., New Taipei City 221, Taiwan
Europe
IC Intracom Europe
Löhbacher Str. 7
D-58553 Halver, Germany
Page 39
manhattanproducts.com
All trademarks and trade names are the property of their respective owners.
© IC Intracom. All rights reserved. Manhattan is a trademark of IC Intracom, registered in the U.S. and other countries.
Loading...