Mamas & Papas Bop Hi-Lo Instruction manual

HD5 0RH, UK

mamasandpapas.com mamasandpapas.ca mamaspapas.kr

+44 (0)845 268 2000

1-800-490-0331

1-800-667-4111

1300 663 034

LOT

x1 <15m

/mamasandpapasuk /mamasandpapasusa /mamasandpapasmaltaregion /mamasandpapasmagyarorszag

@mamasandpapas /user/mamasandpapasglobal mamasandpapasblog.com /mamasandpapas

BHHC_0365_0114_V1

Bop Hi-Lo

slot. the pin inwards and removing the leg from the

14. Remove the lower parts of the legs by pressing

the chair. rotate the support upwards until it comes free of

11. Turn the locking button anti-clockwise and

• The highchair is suitable from 6 months to 3 years.

• The highchair can be cleaned using warm water and a mild soap. Never use bleach or abrasive cleaners.

• Do not to use the high chair if any part is broken, torn or missing.

• This highchair is only suitable for children who can sit up unaided.

seat pad. Remove the harness. inthe seat, then slot them through the slots in the

13. Slot the harness buckles through the slots

• IMPORTANT: Ensure the tray is secured in position at all times when the child is in the highchair

vicinity of the high chair.

• Be aware of the risk of open ﬁre and other sources of strong heat, such as electric bar ﬁres, gas ﬁres etc. in the

• Do not use the high chair unless all components are correctly ﬁtted and adjusted.

• Ensure that the harness is correctly ﬁtted and adjusted when the child is in the highchair.

• Do not leave the child unattended.

WARNING:

IMPORTANT! KEEP FOR FUTURE REFERENCE

the lock and pull the footrest out of the housing.

12. Push the pin (1) towards the footrest to release

highchair. inwards and lift the tray upwards off the

10. Press the catch on the top of the tray support

1. Attach the two front legs to the seat. Slot the ends of the legs into the housings on the seat. Push the pins in the tops of the legs in and slide into the housings (1), ensure the ends of the bars on the seat are inserted into the housings on the legs (2). Ensure the pins are protruding through the holes in the housings after ﬁtting.(3)

2. Slot the two back legs into the rear housing on the seat. Push the pins on the legs inwards and fully insert into the housing. Ensure the pins are protruding through the holes in the housings after ﬁtting.

3. Slot the feet onto the ends of the legs. Ensure the feet are slotted onto the correct legs. The base of the feet are marked with two letters, see diagram for the correct ﬁtting.

5. Attach the tray support to the front of the seat. Slot the tabs on the back of the support into slots in the seat (1). Rotate the support down until the front locks onto the seat (2).

4. Slot the end of the footrest into the housing on the underside of the seat. Push the leg rest in until it locks into the housing.

6. Slot the hooks on the ends of the tray into the slots in the sides of the seat (1). Ensure the feet on the ends of the tray are resting on the buttons on the seat under the tray (2). Push the tray down until it locks onto the tray support (3).

7. Slot the buckes on the ends of the harness straps through the slots in the seat pad. Place the seat pad in the seat and slot the buckles through the slots in the seat.

8. Slot the tabs on the waist straps into the buckle (1). To adjust the harness, slide the straps through the adjusters to the required lengths (2).

9. To open the harness, push the locking tabs inwards (1) and slide the two waist strap tabs out of the

buckle (2).