OPERATING INSTRUCTIONS
DUST EXTRACTOR CPD/3.C
0909
CONTENTS
TECHNICAL DATA……………………………………………………………….1
UNPACKING AND CHECKING CONTENTS………………………………….2
ASSEMBLY………………………………………………………………………..2
SAFETY RULES………………………………………………………………….5
WIRING DIAGRAM……………………………………………………………....6
PARTS DIAGRAM……………...…………………………………………….…..8
PARTS LIST…………………………………………………………………….…9
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
TECHNICAL DATA
Motor power (Watt) 2200
Inlet diameter (mm) 1-150/3-100
Fan diameter (mm) 305
Bag capacity (cubic meter) 0.43
Overall size (LWH)(MM) 1460x720x1860
Weight (kgs) 59
1
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
READ THIS MANUAL CAREFULLY BEFORE ASSEMBLY, TESING AND
OPERATING.
WARNING: DO NOT OPERATE THIS UNIT UNTIL THE PVC HOSE IS
INSTALLED ONTO THE DUST INLET PORT.
UNPACKING AND CHECKING CONTENTS
Unpack carton, check machine, to see parts listed below:
A. CONNECTOR
B. COLLECTOR BODY & FAN/MOTOR ASSEMBLY
C. TWO COLLECTOR
D. BASE PLATE
E. TWO UPPER BAG SUPPORT
F. TWO SUPPORT
G. INLET
H. FOUR BAGS
I. PACKING
J. FOUR CASTERS
K. NUTS, SCREWS, WASHERS, SPRING WASHERS
L. MOTOR BASE
O. BAG CLAMP
ASSEMBLY
To assemble, first place the base plate upside down and attach the four casters
to the holes provided and tighten with wrench. Fig 1
2
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
Fig 1
With the motor base, collector body & fan/motor assembly in place, secure it to
the base plate using the screw and washers provided as shown in Fig 2.
Fig 2
Install the packing and square connecting tube, connector to the collector body
assembly using screw and washers provided. Fig 3 & Fig 4.
Fig 3
3
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
Fig 4
Next install the two collectors (C) two packing (I) to the outlet as shown in Fig5.
Fig5
Install the two collector supports (F)and two upper bag support (E) as shown
in Fig 6.
Fig 6
4
Next, hang the two bags (H) from the support rods. Then attach the two filter
bags and two collection bags to the collectors using bag clamp.
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
The inlet can now be placed on the intake hole of the fan/motor assembly as
shown Fig 7.
Fig 7
The dust collector is now ready to be placed into service. Before connecting to
a power source, be sure the power source is properly grounded and is of
proper voltage and amperage.
SAFETY RULES
1. Read and become familiar with the entire operating manual.
2.Keep guards and cover in place and in working order.
3.Wear eye protection at all times. Use safety glasses with side shields or
safety goggles, meeting the national safety standards, while operating this
machine.
4. Keep work area clean and well lighted. Clutter and inadequate lighting invite
potential hazards.
5.Ground all tools. If a machine is equipped with a three-prong plug, it must be
plugged into a three-hole electrical outlet or grounded extension cord. If
using an adapter to aid in accommodating a two hole receptacle, ground
using a screw to a known ground.
6. Avoid dangerous environments. Do not operate this machine in wet or flame
environments. Airborne dust particles could cause an explosion and severe
fire hazard.
7. Make sure switch is in the “OFF” position before connecting power to
machine.
8. Keep children and visitors away. All visitors should be kept a safe distance
away while operating unit.
9. Childproof workshop with padlocks, master switch or by removing starter
keys.
5
10. Disconnect machine when cleaning, adjusting or servicing.
11. Do not force tool. The machine will do a safer and better job at the rate for
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
which it was designed.
12. Use correct tool. Do not force machine or attachment to do a job for which
it was not designed.
13. Wear proper apparel. Do not wear loose clothing, neck ties, gloves,
jewelry, etc.
14. Remove adjusting keys and wrenches. Before turning the machine on,
make it a habit to check that all adjusting keys and wrenches have been
removed.
15. Do not leave machine unattended. Wait until it comes to a complete stop
before leaving the area.
16. Do not use dust collector for anything except wood dust. Material such as
liquids, metal shavings, metal dust, screw, glass, plastic or rock can cause
sparks when coming into contact with any part of the collection system.
17. Do not place your hands, lumber or tools near inlet opening while machine
is running or connected to power.
18. Always wear a respirator and safety glasses when removing, emptying or
replacing collection bags. Secure bags tightly to dust collector to avoid
bags from “blowing off”.
6
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
7
WIRE DIAGRAM:(SINGEL PHASE)
WIRE DIAGRAM:(THREE PHASE)
PARTS DIAGRAM
8
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
PARTS LIST
Part No. Description Part No. Description
1 CASTER 23 COLLECTOR SUPPORT
2 SCREW 24 RIGHT-COLLECTOR
3 SCREW 25 WASHER
4 BASE PLATE 26 UPPER BAG SUPPORT
5 SCREW 27 FILTER BAG
6 INLET 28 PACKING
7 SCREW 29 INLET
30 KEY
9
WASHER
31 SWITCH
10
TURBO FAN
33 WRENCH HEX
11 COLLECTOR
34 CABLE
12
WASHER
35 CAP
13 MOTOR BASE
36 BAG CLAMP
14 SCREW HEX
37 SWITCH BOX
15
SCREW HEX
38 HEAD SCREW
16
BOLT
39 SCREW
17
MOTOR
44 WRENCH
18
NUT
19
CONNECTOR
20
SCREW
21
LEFT-COLLECTOR
22
COLLECTOR BAG
9
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
Loading...