MAKSIWA CBC.EC Instruction Manual
CBC.EC
Edge Bander
INSTRUCTION MANUAL
Attention: Read this manual before using your machine.
1
INSTRUCTION MANUAL
Important information you should know:
• The images in this manual are illustrative and are
meant to demonstrate the correct operation of your
product, there may be small changes in relation to the
images.
On-Line Support: In our YouTube
Channel you will nd several videos
that will help you whit Maksiwa´s
machines. To use the QRCODE.
READ ALL INSTRUCTIONS
CAUTION:
WHEN DOING MAINTENANCE, REPLACE ONLY
WITH IDENTICAL PARTS. Repair or replace damaged
wiring.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. For cord
length of up to 50 feet, use a cord of 14 gauge. For a
cord length of 50 to 100 feet, use a cord of 12 gauge.
A cord length over 100 feet is not recommended. If in
doubt, use the next heavier gauge. Smaller the gauge
number, heavier the cord.
• This edgebander is intended for use on a circuit that
has an outlet similar to the one illustrated in Sketch
A. The edgebander has a grounding plug similar
to the plug illustrated in Sketch A. Make sure the
edgebander is connected to an outlet having the same
conguration as the plug. No adapter is available or
should be used with this edgebander. If the machine
must be reconnected for use on a dierent type of
electric circuit, the reconnection should be made by
qualied service personnel; and after reconnection,
the edgebander should comply with all local codes
and ordinances.
GROUNDING INSTRUCTIONS
• THIS EDGEBANDER MUST BE CONNECTED TO A
GROUNDED WIRING SYSTEM or to a system with
an equipment-grounding conductor. In malfunction
event, grounding provides a path of least resistance
for electric current to reduce the risk of electric
shock. This edgebander is equipped with an electric
cord having an equipment grounding conductor
and a grounding plug. The plug must be connected
into a matching outlet provided – if it will not t the
outlet; have the proper outlet installed by a qualied
electrician. Improper connection of the equipmentgrounding conductor can result in a risk of electric
shock and/or malfunction. If repair or replacement
of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to
a live terminal. Check with a qualied electrician or
service personnel if the grounding instructions are not
completely understood or if in doubt as to whether
the edgebander is properly grounded. Use only 3-wire
extension cords that have 3-prong grounding plugs
and 3-pole receptacles that accept the edgebander´s
plug.
• REPAIR OR REPLACE A DAMAGE OR WORN CORD
IMMEDIATELY. When servicing use only identical
replacement parts.
SAFETY INSTRUCTIONS
FOR ALL EQUIPMENTS
WARNINGS
• Keep a clean work surface. Cluttered areas and work
surfaces are invite accidents.
• Do not use the Edgebander in hazardous
environments. Do not use machine in damp or wet
locations or exposed to rain. Keep well-lit work area.
• Keep children away. Visitors should be kept safe
distance from work area.
• Make the workplace childproof making use of
padlocks, master keys or removing the ignition key.
• USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough
to carry the current your edgebander will draw.
• Do not force tool. It will perform the job better and
safer for the intended use.
• Keep children away. Visitors should be kept safe
2
distance from work area.
• Make the workplace childproof making use of
padlocks, master keys or removing the ignition key.
• Do not force tool. It will perform the job better
and safer for the intended use.
• Use appropriate equipment. Do not wear loose
clothing, gloves, chains, rings, bracelets or other
accessories that could become caught in moving
parts.
• It is recommended wearing shoes with non-slip soles.
Use protection for the hair in order to hold them.
• Always wear safety glasses. Also use hearing
protection.
• Do not overreach on the equipment. Maintain
balance and feet in comfortable position at all times.
• Extension cables. Make sure your extension cord is
in good condition. When using an extension, be sure
of their ability to transmit the electrical current used
by your product. An undersized cord will cause drop
in voltage resulting in loss of power and overheating.
The following table shows the correct size to be used
depending on the cable diameter and amperage rate.
If in doubt, use a cable with a higher level of capacity.
IMPORTANT: Do not use an extension cord with
length above 20 meters.
Cable 2 wires Cable 3 wires
Ø (mm²) Amperage Ø (mm²) Amperage
0,5 9 0,5 8
1,0 13 1,0 12
1,5 16,5 1,5 15
2,5 23 2,5 20
• Keep all tools in order. Keep tools sharp and clean for
better and safer performance. Follow the instructions
for lubricating and changing accessories.
better and safer performance. Follow the instructions
for lubricating and changing accessories.
• Unplug the machine before servicing or changing
accessories such as scissors, cutters etc.
• Reduce the risk of unintentional starting. Ensure
that the switch is in the “OFF” position (o) before
connecting the wire to the plug.
• Use recommended accessories. See the instruction
manual to check recommended accessories. Improper
use of accessories may cause risk of injury to persons.
• Never step on the machine. May occur serious
accident if the machine is dented or if parts are
accidentally touched.
• Check for damaged parts. Before continuing the use
of Edgebander, a guard or other part that is damaged
should be examined carefully to determine its proper
operation and perform its function properly. Check
the alignment of moving parts, breakage of parts,
mounting and any other condition that may aect
its operation. Any part that is damaged should be
repaired or replaced immediately. Do not use the tool
if the switch does not turn on or o.
• Never leave a running tool unattended. Turn o the
ignition key.
• The engine of this machine can emit sparks, and
explode ammable gases.
Additional safety rules for Edgebander:
CAUTION: FAILURE TO ATTEND THESE WARNINGS
MAY RESULT IN PERSONAL INJURY AND SERIOUS
DAMAGE TO THE MACHINE.
ALWAYS USE PROPER PROTECTIVE
EQUIPMENTS TO OPERATE THIS
MACHINE.
• Always use safety glasses. Also use face or dust mask
if cutting operation is dusty. Everyday eyeglasses only
have impact resistant lenses, they are NOT safety
glasses.
• Keep guards in place and working order.
• Protect the electric power supply line with at least a
20 amp fuse or a circuit breaker switch.
• Make sure that the advance is turning in the right
direction.
• Make sure that the knobs and screws are properly
tightened and safe before starting any operation.
• Keep sharp tools.
• Keep vents free of chips or dirt engines.
• Keep hands away from moving or sharp parts.
• Turn o the machine and unplug the power cord
before maintenance or adjustments of the tool.
• Support long pieces with a clamping device for
wood.
3
• Do not attempt to operate the machine in another
voltage beyond designated.
• Do not use larger or smaller tools than recommended.
• Do not apply lubricant to the tools during use.
• Do not operate without some parts of the machine.
• Do not put your hands less than 4in from the shaft.
• Do not put your hands in closed parts of the machine
unless it is turned o and unplugged.
• Do not use lubricants or cleaners (particularly sprays
and aerosols) in the vicinity of the plastic guard. The
polycarbonate material used in the guard is sensitive
to certain chemicals.
WARNING: Some dust created by the act of sanding,
cutting, grinding, drilling and other constructionrelated activities contains chemicals that can cause
cancer, birth defects or other reproductive harm.
Some examples of these products are: Lead-based
paint; crystal silica bricks, concrete and other masonry
products; and arsenic and chromium from chemically
treated wood.
parts and will need to know where they are.
Especications
Power: 1.500 W
Tape Thickness: 0,3 a 2,0 mm
Max. Tape Width: 80 mm (3’’)
Min. Worpiece Length: 120 mm (4 3/4’’)
Feeder Speed: 5,5 m/min (18 ft/min)
Temperature Range: 120°C to 220°C (248°F to 428°F)
Voltage: 110V – 1 phase
Net Weight: 52 Kg (115 pounds)
Transport and Installation
By ergonomic issues, this equipment must be carried
by at least two people, holding by the handles located
on the sides of the box.
CAUTION: Do not connect the unit to the power outlet
until all instructions have been read and understood.
Always tighten the adjustment tabs before using the
machine. Think: “I can prevent accidents”.
Do not operate the machine unless the guards are in
their proper places. Always use protective goggles.
Electrical connection
The Edgebander CBC.E MAKSIWA has engine 1-phase
110V. To avoid burning risk, check the voltage of your
outlet before starting the machine. If necessary make
the change of your power with the help of a specialist.
Ensure that your power supply is in accordance with
the designated on the board. A 10% decrease in voltage
or more will cause loss of power and overheating. All
equipment MAKSIWA are tested at the factory. If this
machine does not work, check the electricity supply.
Check the compatibility of your outlet and plug the
machine. Do not do patches and adaptations.
To avoid electrical shock and damage to the equipment
always ground the machine.
For packaging purposes, the machine is not fully
assembled. If you notice any damage caused by
transportation, while you open the package, notify
your supplier immediately. Do not operate the
machine.
Dispose the packaging in a friendly way with the
environment.
The Edgebander is designed to operate indoors and
should be placed on a rm, stable and level surface.
CAUTION: To prevent the machine from moving and
causing lack of precision, ensure that the base where
it is supported is not uneven.
Familiarization
Put the machine on a smooth and at surface. Check
the pictures and watch the descriptions to familiarize
yourself with its components. The next section will
deal with the necessary adjustments for the proper
functioning of the machine. You should know these
4
UNPACKING AND ASSEMBLY
Due to modern mass production techniques, it is
unlikely that Edgebander CBC.E MAKSIWA is faulty
or have parts missing. If you nd anything wrong, do
not use the machine until the parts are replaced or
the fault is corrected. By doing this you are avoiding
serious injury.
Step 01: Open box and tip on to it’s back.
Step 02: Slide machine out using plastic wrap.
Remove inner plastic wrap.
Step 03: Flip legs down and install cross bars – Note
tapered ends.
Step 04: Add rubber feet.
Step 05: Lift machine onto feet, install angled
extension plate on rear corner.
Step 06: Plug machine in to test power.
5
WARNING: TURN THE MACHINE IN 110V SINGLE
PHASE.
If will need a extension Cord, utilize a cable with 3
wires with 1,5mm² (or more).
ADJUSTMENTS
ADJUSTMENTS
NOTE: The brand and quality of the glue is
fundamental. The MAKSIWA recommends glues that
work in the range of 160°C to 190°C. On top of that,
high temperature and melt glues can damage the
tape.
GLUE EXCHANGE: If you change the color of your tape
or the color of the wood panel, you may change the
glue on your Edgebander. To change the glue follow
these steps, but rst read the rest of this manual to be
familiar with all operations:
- Turn on the machine and set the temperature
controller to 70°C (158°F) (see this manual to program
the controller).
- At this temperature, the glue is not too hot (soft)
or too cold (hard). So you can remove the entire glue
without much diculty.
- Use a trowel or piece of wood, avoiding scrape the
walls of collared, damaging the same.
- After removing all the glue, put the new glue.
- Set the temperature controller according to the
specication of the glue again.
The following shown adjustments must be made
before using your Edgebander CBC.E for the rst
time or when some kind of change is made as thick
tape or thickness of the wood.
CAUTION: ANY ADJUSTMENT NEEDS TO BE MADE
WITH THE MACHINE OFF AND DE-ENERGIZED
(unplugged).
1. GLUE
The glue to be used in your Edgebander CBC.E
MAKSIWA is granulated glue type Hot Melt.
Always check the amount of glue on your machine.
Because of factory tests, their CBC.E can go with a
certain amount of glue.
GLUE INDICATIONS: With this machine we
recommend the following glue brands:
• Artecola - 160ºC a 180ºC - Ivory-Color. Cod. 1820
White. Cod. 1821
• Durante Duditerm - 160ºC a 180ºC - White. Cod.
715/15
• Jowat - 150ºC a 180ºC - Ivory-Color. Cod. 282.20
White. Cod. 282.21
• Proadec - 160ºC a 180ºC - Ivory-Color. Cod. 5707
• Kleiberit - 150ºC a 180ºC - Ivory-Color. Cod. 788.3/20
White. Cod. 788.3/10
2. TAPE (EDGEBAND)
The Edgebander CBC.E MAKSIWA is designed to work
with PVC tape, ABS, paper and wood that do not have
glue, only straight parts. Use tapes approximately
4mm wider than the wood panel.
It is necessary to regulate the Edgebander according
to the thickness of the tape. That is, when changing
the thickness of the tape, it is necessary to adjust the
machine again. For this setting, follow these steps:
- Cut a piece of tape to be used.
- Loosen (without removing) the two screws shown in
the following gure, using a wrench 13:
If necessary insert adequate glue to the color of panel
wood and tape that you are using.
Do not put too much glue, because when it melt and
during operation of the machine may overow and
cause leaks. Let also not miss glue in the glue pot
because this can cause failures in the collage.
6
Loading...