MAKSA 44416, 44418 Instruction Manual

Solar-Powered, Motion-Activated Dual Head LED Security Light

ASSEMBLY AND INSTRUCTION GUIDE

Model #: 44416-44418

IMPORTANT: Read all instructions carefully before use.

Page 1

ABOUT YOUR SOLAR SECURITY LIGHT

The Motion-Activated Dual Head LED Secu­rity Light turns on automatically at night when
motion is detected. This MAXSA Solar Secu­rity Light has an adjustable TIME dial that
allows light duration of up to 1 minute.
Because the light runs off of solar power using
free energy from the sun, it never costs you
electricity and can be mounted anywhere the
solar panel can receive sunlight.

INCLUDED PARTS

Carefully remove and identify all the parts
from their protective packaging and lay them
out in front of you.

CHOOSING A LOCATION

This Solar Powered Motion-Activated Dual
Head LED Security Light comes complete
with a 15 foot cord so you can place your
Motion-Activated Dual Head LED Security
Light anywhere where sunlight is available.
Ensure that the Motion-Activated Dual Head
LED Security Light is not placed near night
time light sources such as porch lighting or
street lighting.

This Motion-Activated Dual Head LED Secu­rity Light is ideal for areas where electricity is
not available, including carports, outside
garages, porches, decks, and outside areas.
The lights provide safety and security around
your home, business or community building.

When deciding where to mount the light, keep
in mind that the motion sensor has a field of
vision of 130º (horizontal) at a distance of 30
feet when the surrounding temperature is
75ºF. The outside temperature will impact the
detection distance.

INSTALLING THE LIGHT

Page 2

HOW TO INSTALL

Your Motion-Activated Dual Head LED Security
Light works best when installed with the round
motion sensor at the bottom. To install the light
onto a solid surface, remove the screws on the
top and bottom of the back section and slide the
plastic end piece off the light.

Mount the back piece using the 2 supplied
screws (and the wall hangers if needed) utilizing
the two mounting holes in the piece.

After the end piece is secured, slide the main
body of your light back onto the end piece and
replace the two screws holding it in place.

Be sure that a power source is within range of
the 15 foot power cord as the light will not func­tion if it does not receive power from the solar
panel. (There are extension cords available if
you need more than 15 feet to go from the solar
panel to the light . See end

Choose a location that receives plenty of sun.
Ideally 6-8 hours of sunlight per day is required
to fully recharge your security light. The solar
panel should be facing south to get the most
sunlight.

of instructions).

reduce the number of hours when the Solar
Security Light will operate per evening.

In choosing a location for your Solar Security
Light, ensure that the solar panel is not placed
near nighttime light sources such as porch light
or street lighting.

The solar panel can be mounted vertically or
horizontally onto a solid surface using the sup-

plied wood/sheet metal screws and anchors.
You can adjust the angle of the solar cell by
moving the angle adjustment on the solar panel
to different locking positions. Remember it is
best to face the panel south for direct sunlight
exposure.

Placing the solar panel in a shaded location will
not allow the batteries to charge fully. This will

STORAGE

COLD WEATHER

In temperatures below 20ºF, the Solar Powered
Motion-Activated Dual Head LED Security Light
may not work as well. Normal performance will
return when the temperature rises.

SAFETY TIPS

Do not cut the power wire. Discontinue use if the
wire becomes frayed or broken.

Do not immerse the Motion-Activated Dual Head
LED Security Light in water or other liquid.

Position the cord from the solar panel to the light
so that it is securely fastened and will not move
around or cause someone to trip over the cord.

MAINTENANCE TIPS

The LED lights in your Motion-Activated Dual
Head LED Security Light will last up to 30,000
hours and should never need replacement.

The batteries will last approximately 3 years.
The batteries can be accessed after removing
themounting bracket. The battery we use are 3
pieces 1.2V Ni-MH 2200 mAh AA sized
rechargeable batteries.

To keep your Motion-Activated Dual Head LED
Security Light looking new, keep the lens free of
dust and deposits by wiping occasionally with a
dry cloth or with warm soapy water.